load velocity curve 中文意思是什麼
load velocity curve
解釋
負荷速度曲線-
In different in terne die travel, the metal flow characterize in warm extrusion forming processes and the affection for the flow of metal stage which made by the difference between the blank bottom altitude and the axial direction limiting size in warm extrusion forming technique have been analysed we have gotten the equivalent strain field and the velocity field and other field variable that the blank in different in terne die travel and the die travel - load curve. at the same time, we have analyzed the contributing factor for the oil pump stator forming process optimized and achieve thereasonable die parameter for the war m extrusion forming finally, the optimized technics parameters were used into pilot production, then the qualified oil pump stator forging were produced, the analog results were compared with those of pilot production
論文具體分析研究了不同成形工藝過程中金屬流動的特點，並對不同凸模行程下溫擠成形過程中的金屬流動特點、坯料連皮厚度（底部高度）與溫擠壓成形工藝中的軸向界限尺寸的差值對金屬變形階段的影響進行了分析，獲得了坯料在不同凸模行程下的等效應變場、速度場等場變量及凸模行程-載荷曲線，同時對油泵定子成形過程的影響因素等進行了分析，優化並獲得了合理的溫擠成形工藝及模具參數。最後，利用模擬優化獲得的各項工藝參數進行生產實驗，得到實際生產出的合格油泵定子件，並將模擬結果與生產實驗結果進行比較。 -
According to the frndamental and the steps of this method, we cans use the linear regress filter method to make the simulation of the wind load and then we can educe the curve of the time - process wind velocity. after that step, we can get the chart of the dynamic wind load which we can deliver the crosswind into the particle wind load and put them on the corresponding cell nodes. then we can do the analysis of the dynamical wind load through the time - process analysis to get the max value of the displacement
根據線性回歸濾波器法的基本原理和步驟，藉助相關軟體進行風荷載的人工模擬並得出風速時程曲線，進而轉化為風動力譜，由此將橫風向風力表達成節點風荷載作用於相應的單元節點上，按時程分析法對該空間桁架體系進行風荷載的動力分析，求出結構在進行風動力荷載分析時，結構相應節點對應的最值位移值。 -
The simulated test of the mechatronics soft start equipment is made regarding the experimental platform of belt conveyor as load, the sensor design is had for selecting type, the testing datum are gatherd and analyzed, the rational curve of velocity in the starting and braking progress are gained, the best matching ratio of driving power for the double asynchronous moters is found
以帶式輸送機實驗臺為負載進行了機械電子式軟起動裝置的模擬試驗，對傳感器進行了選型設計，對試驗數據進行了採集與分析，確定了合理的起、制動速度曲線，求出雙電機驅動功率的最佳配比。 -
Based on the constitutive relationship coupled microstructure evolution, 3d - fe simulation of isothermal forging process of tc6 titanium alloy disc is performed dealing with different deformation temperature, punch velocity and shear factor of friction, effect of process parameters on equivalent strain, equivalent stress and grain size is calculated, and load - displacement curve is calculated
本文基於微觀組織演變的本構關系模型，對不同變形溫度、凸模速度和摩擦條件下鈦合金盤的等溫鍛造過程進行了三維數值模擬，研究了變形工藝參數對等效應變、等效應力和晶粒尺寸的影響，計算了各變形條件下的位移?載荷曲線。 -
The results indicate that the load transfer law of squeezed branch pile is similar to that in the ordinary soil, the velocity of load - settlement curve changes slowly and the pile has high load bearing capacity, the principle of load transfer has apparently sequence
結果表明，支盤樁荷載沉降曲線為緩變型，具有較好的承載性能，荷載傳遞規律與在非濕陷性黃土地基中具有相似的性質，樁身各段承載力的發揮具有明顯的順序性。 -
Adopting the deformation harmony theory, the numeric calculation of the curve of load versus settlement is made. the fitting results between the calculated curve of load - settlement and the measured one of piles with different construction process are illustrated. hence, under the condition of few or no static load test data, the performance of bearing capacity of single bored pile in loess may be predicted utilizing indexes of shear wave velocity, static cone penetration test and modification coefficient of depth, so it is remarkable to reduce the blindness of preliminary design of pile
通過室內試驗及原位測試指標進行理論計算與現場實測值的對比，筆者引入了施工工藝修正系數k _ （ c1 ）和k _ （ c2 ）及深度修正系數，使理論計算值與現場實測值具有良好的一致性，進而通過變形協調理論對荷載?沉降曲線進行數值計算，並用不同施工工藝的實例說明了理論計算荷載?沉降曲線與實測荷載?沉降曲線的擬合效果，從而達到可在不做靜載荷試驗或少做靜載荷試驗的情況下通過剪切波速和靜力觸探試驗指標以及施工工藝修正系數等預測黃土地基中鉆孔灌注樁承載性狀，這對于工程初步設計中減少設計的盲目性具有十分重要的現實意義。
分享友人