loads testing 中文意思是什麼
-
Standard specification for testing and establishing allowable loads of joist hangers
檢驗和確定擱柵吊鉤允許荷載的標準規范 -
Medical microbiology - susceptibility testing of pathogens to antimicrobial agents - part 2 : active substance carriers for the agar diffusion test ; carrier loads and values required for drawing a standard curve
醫療微生物學.病原細菌對殺菌劑敏感性的檢測.第2部分 -
Loads are commonly applied with universal testing machines, hydraulic cylinders dead weights, or some form of pressure.
通常是用萬能試驗機、液壓缸重物或某種形式的壓力施加載荷。 -
C2 is for testing the resistant ability to load variations and over loads
C2 :檢測trihal的抗負荷變化和過負荷能力 -
The parameter measurement information section of the data sheet illustrates the test loads and waveforms that are used when testing the device ( see figure 10 )
在測試器件時，數據手冊的參數測量信息小節，舉例說明測試負載和測試波形（參見圖10 ） 。 -
Starting from studying various environmental loads during the ship undocking process, an environmental loads calculation model and the environmental loads testing methods are established in this dissertation utilizing the orthogonal design theory. this dissertation also analyzes the impacts of the environmental loads at various ship undocking conditions. utilizing the current optimization technique and fuzzy evaluation method, this dissertation creatively studies the tug configuration mechanism and the ship motion simulation forecasting during the ship undocking process
本文從探索船舶出塢過程中的各種環境條件出發，利用正交設計理論制定了一套船舶出塢過程的環境載荷計算模型和環境載荷試驗測試方法，分析了在不同的出塢環境條件中，作用於船舶的環境載荷對船舶出塢的影響程度，利用目前的優化技術和模糊評價方法，率先研究和探討了船舶出塢過程中，拖輪配置機理、拖輪配置數量和方法，以及船舶出塢過程的運動模擬預報，還討論了擋水板對船舶出塢影響這一特殊問題。 -
Road vehicles - environmental conditions and testing for electrical and electronic equipment - part 2 : electrical loads
道路車輛.電氣和電子設備的環境條件和試驗.第2部分:電力負載 -
Abstract : the results of hi - lo strain - gauge test on 9 dead - load testing piles are analyzed. the bearing strength of single piles is evaluated preliminarily by using high strain and low strain process and conditions for correlating dynamic and dead loads and technical factors affecting the test accuracy are discussed
文摘:通過對一組靜載試驗樁高低應變動測結果的分析，對高應變法、低應變法檢測單樁承載力的可靠性作出了初步評價，並對動靜對比成立的條件及影響其測試準確性的一些技術因素進行了探討。 -
Packaging - complete, filled transport packages and unit loads - conditioning for testing
包裝.滿裝的運輸包裝件和單元貨物.試驗狀態的調節 -
External blinds and shutters - resistance to wind loads - method of testing
外百葉窗和遮板.抗風力.試驗方法 -
Packaging - complete, filled transport packages - stability testing of unit loads
包裝.滿裝的運輸包裝.成組貨件穩定性試驗 -
Packaging - complete, filled transport packages - stability testing of unit loads iso 10531 : 1992
包裝.滿裝的運輸包裝.單元貨物穩定性試驗 -
The microscopic plastic deformation of the local crazes cause the change of crack opening loads. therefore, the fatigue crack closure concept could be introduced. a crack closure model of mdyb - 3 pmma were recommended and phenomenologically formulated for positive and negative stress ratios separately, according to the testing results of fatigue crack propagation
本文討論了有機玻璃疲勞裂紋擴展機理，提出，銀紋的形成是裂紋形成和擴展的基礎，從微觀上解釋了裂紋形成和擴展的原因，並結合金相分析結果，明確提出塑變誘導閉合和粗糙誘導閉合是有機玻璃疲勞裂紋面閉合的兩個主要原因，成功的解析了裂紋面的閉合現象。 -
Combined the real testing data, the paper developed a calculation program of water wall temperature and pressure drop for designed supercritical pressure cfb boiler with vertical water walls. the hydrodynamic calculation and safety checkout under five loads was carried out
結合實際運行的循環流化床鍋爐的熱態測試數據，開發了垂直水冷壁壁溫及水動力計算程序，根據爐膛熱負荷分佈規律，建立了膜式水冷壁熱流密度分佈函數。 -
External blinds and shutters - resistance to wind loads - method of testing ; german version en 1932 : 2001
外遮簾和遮板.風力載荷耐受性.試驗方法 -
Unit loads - stability testing
成組貨件.穩定性試驗 -
Road vehicles - environmental conditions and testing for electrical and electronic equipment - part 4 : climatic loads
道路車輛.電氣和電子設備的環境條件和試驗.第4部分:氣候荷載 -
Road vehicles - environmental conditions and testing for electrical and electronic equipment - part 5 : chemical loads
道路車輛.電氣和電子設備的環境條件和試驗.第5部分:化學荷載 -
2. specimens ’ cracking loads under dead - load have been calculated based on the tension model of ordinary concrete. the calculating value is larger than the testing value by 29 % to 37 %
2 、按照普通混凝土的受拉本構模型計算試件靜載下的開裂荷載，計算值比實測值大29 % 37 % 。 -
Stress ( overload ) testing identifies the predicted point of failure where servers fail to handle loads
壓力（負載）測試主要是找出失敗的點（服務器處理壓力失敗） 。
分享友人