low burner 中文意思是什麼
low burner
解釋
低燈頭-
Mean while, the iouver concentrator structure principle is analyzed, the iouver puiverized coal concentrator is studied on the bases of both laboratory and production. lt is discovered from the experiments that the louver horizontai rich / lean combustion pulverized coal burner has advantages of simple in structure, low resistance and adjustment of pc concentration
同時，重點分析了百葉窗濃縮器的結構原理，並在試驗臺上和現場對百葉窗煤粉濃縮器進行了大量的試驗研究，結果表明：百葉窗式水平濃淡煤粉燃燒器具有結構簡單、阻力損失小、分離調節方便等一系列優點。 -
The paper introduced the run characteristics and their designed load performance of large - scale units with output of 200mw and over in hubei province, as well as their improved load performance after the modification of burner for low - load stable combustion
摘要簡要介紹了湖北省200mw及以上大型燃煤鍋爐機組的運行特性、設計調峰性能，以及經過對燃燒器進行低負荷穩燃改造以後，調峰能力的改善。 -
Abstract : the in servie tubular heaters built early in refineries and chemical plans have low thermal load and low heat efficiency, therefore measures for technical reform are offered, including ( 1 ) enlarging the surface area of convection tubes to increase the thermal load of rhe convection section ; ( 2 ) increasign the heat interchanging area of radiant tubes ; ( 3 ) changing the height of the chimney ; ( 4 ) using new burner with forced air supply to increase calorific capacityu ; ( 5 ) adding air preheater between the convection section and chimney to enhence the temperature of the air entering the furnace ; ( 6 ) adopting high temperature radiant coating to improve the effect of radiant heat interchanging
文摘:針對早期建造的煉油廠和化工廠在役管式加熱爐熱負荷和熱效率低的狀況，提出了若干技術改造措施包括，增大對流管表面積以增大對流段的熱負荷；增加輻射管的換熱面積；修正煙囪高度；換用新型燃燒器，變自然通風為強制供風，以增大燃燒器的發熱量，減小過剩空氣系數，節省燃料2 % 3 % ；在對流段和煙囪之間增設空氣預熱器以提高空氣入爐溫度；採用高溫輻射塗料增強輻射換熱效果，從而增加熱源對爐壁的輻射傳熱量和爐管的傳熱量等。 -
The in servie tubular heaters built early in refineries and chemical plans have low thermal load and low heat efficiency, therefore measures for technical reform are offered, including ( 1 ) enlarging the surface area of convection tubes to increase the thermal load of rhe convection section ; ( 2 ) increasign the heat interchanging area of radiant tubes ; ( 3 ) changing the height of the chimney ; ( 4 ) using new burner with forced air supply to increase calorific capacityu ; ( 5 ) adding air preheater between the convection section and chimney to enhence the temperature of the air entering the furnace ; ( 6 ) adopting high temperature radiant coating to improve the effect of radiant heat interchanging
針對早期建造的煉油廠和化工廠在役管式加熱爐熱負荷和熱效率低的狀況，提出了若干技術改造措施包括，增大對流管表面積以增大對流段的熱負荷；增加輻射管的換熱面積；修正煙囪高度；換用新型燃燒器，變自然通風為強制供風，以增大燃燒器的發熱量，減小過剩空氣系數，節省燃料2 % 3 % ；在對流段和煙囪之間增設空氣預熱器以提高空氣入爐溫度；採用高溫輻射塗料增強輻射換熱效果，從而增加熱源對爐壁的輻射傳熱量和爐管的傳熱量等。 -
To save time a contractor ' s fit for purpose burner ( usually a propane burner ) supplying large amounts of warm air at low temperature can be used
為節省時間，可採用承包商的適用燒嘴（通常為丙烷燒嘴） ，它在低溫下供應大量熱風。
分享友人