magnet valve 中文意思是什麼
magnet valve
解釋
磁力閥-
Thermal stress analysis of helium cooling lines in control valve box for bepc ssm magnet
磁體控制閥箱內氦冷卻管線熱應力分析 -
Thirdly, it researches the maganetic force of the permanent magnetic circuit and electromagnetic circuit in all kinds of working state. especially, it discusses the working state and the working point of the permanent magnet. it argues the rationality and reliability of the valve that we have designed
再者，本文研究了電磁閥中永磁磁路和電磁磁路在各種工作狀態下的磁力情況，尤其對永磁鐵的工作狀態和工作點進行了全新的探討，驗證了所設計電磁閥的合理性和可靠性。 -
The 3 - way magnet valve ( pos. no. 77 ) is never energized again ( upper frame ), but if the cause of deenergizing is eliminated and the electric circuits of the engine protecting system are reset, the 3 - way magnet valve ( pos. no. 77 ) is energized ( upper frame ), then the control air which has actuated the single - acting cylinder ( pos. no. 21 ) being rapidly blown off through the quick release valve ( pos. no. 41 )
三通電磁閥77決不會再次通電上位，但如果斷電的原因被消除而且主機安保系統電氣迴路被復位，三通電磁閥77被通電上位，作用在單作用汽缸21的控制空氣已被迅速放出通過快速泄放閥41 。 -
Brake release magnet valve
緩解電磁閥 -
Moreover, it is necessary to make a model that can simulate the operation of the valve because occasionally some factors are inaccessible. in this paper, the fundamentals of the valve been comprehended deeply, the model of the valve is brought forward, such factors as the spring, the material of the magnet core, etc are analyzed in detail using matlab simulink
第三，在深入解析電磁閥工作過程的基礎上，為了解決那些在現有條件下難以用試驗方法分析的某些因素對電磁閥性能的影響，建立了電磁閥的物理模型，採用matlabsimulink模擬技術對其進行了模擬研究，分析了諸如彈簧剛度、鐵芯材料等對電磁閥性能的影響，進一步揭示了電磁閥的工作機理。 -
Suitable for each type of dual - surface molding, for example, spring end, bearing, magnet, connecting rod, piston ring, compressor valve and etc
適用於各種雙面加工例如：彈簧端面培林磁鐵連桿活塞環壓縮機閥片等。 -
By deenergizing of coil, control air moves the single - acting cylinder to the stop position through the pipe named “ supply ”, the double check valve ( pos. no. 72 - 2 ), the 3 - way magnet valve ( pos. no. 77, lower frame ) and the 3 - way valve ( pos. no. 78, lower frame )
通過其線圈斷電，控制空氣移動單作用汽缸到停止位置通過supply管路，雙向截止閥72 - 2 ，三通電磁閥77下位和三通閥78 ，下位。 -
By deenergizing of coil, the control air actuates the 3 - way valve ( pos. no. 29 through the pipe named “ supply ” and the 3 - way magnet valve ( pos. no. 73, right frame )
由線圈的斷電，控制空氣促動三通閥29通過supply管路和三通電磁閥73右位。 -
The 3 - way magnet valve ( pos. no. 73 ) is never deenergized, but the cause of energizing is eliminated and the electric circuits of the engine protecting system are reset
三通電磁閥73決不會斷電，但通電的原因被消除而且主機安保系統電氣迴路被復位。 [是否有誤？ -
Then the 3 - way magnet valve ( pos. no. 73 ) is deenergized and the speed setting signal raised by the manoeuvring valve ( pos. no. 01 - ) is transmitted to the p. g. governor again
三通電磁閥73決不會斷電，但通電的原因被消除而且主機安保系統電氣迴路被復位。 [是否有誤？ -
Meanwhile, in the experimental work, the scope of the equation that reveals the relation between the magnet force and the working distance is defined definitely. different materials of the magnet core are compared in terms of their influence to the valve. however, it is only initiatory, more work needs to be done in the future
同時，還採用試驗研究的手段深入分析了電磁閥工作間隙與電磁吸力之間的關系，明確了吸力公式的應用范圍，同時，在不同材料的對比試驗中，分析了磁性能較好的鐵氧體和鐵鉻合金以及工業純鐵對電磁閥工作性能的影響，對合理確定電磁閥鐵芯的製作材料進行了初步的探討。 -
The computer control system of a high - speed industrial sewing machine is studied in the dissertation. the system ' s operation principle, the design nation with the core of 80c196kc mcu ( micro - chip computer ) also are discussed in the dissertation the methods of a minimum operation system of mcu, the principle circuit of signal adjusting, data collecting, keyboard controlling, led displaying, electromagnetic clutch and magnet valve power driver circuit etc. are proposed and realized
論文分析了工業高速自動剪線縫紉機（簡稱工縫機）計算機控制系統的工作原理，提出了以80c196kc單片機為控制核心的系統設計方案，並詳述了關鍵部分的功能與實現方法。設計了電路原理圖，完成了系統軟硬體設計、安裝，調試，和對系統原理樣機的性能測試。
分享友人