magnetic pole method 中文意思是什麼

magnetic pole method 解釋
磁極探傷法
  • magnetic : adj. 1. 磁（性）的；（可）磁化的。2. 吸引人心的；有魅力的。3. 催眠術的。
  • pole : n 1 棒，桿，竿〈通常為十英尺以上圓桿〉。2 旗竿；釣竿；【運】（撐竿跳的）竿；桅桿；電線桿；（車的...
  • method : n 1 方法，方式；順序。2 （思想、言談上的）條理，規律，秩序。3 【生物學】分類法。4 〈M 〉【戲劇】...
  1. The influence of separating magnetic flux method of rotor with u ' s and tangential permanent magnet to the pole - to - pole leakage factor is analyzed by finite element method ( fem ), and given the rule of design

    通過對pmsm進行電磁場求解，分析了u型結構和切向結構轉子磁路結構的隔磁措施對電機極間漏磁系數的影響，提出了設計準則。
  2. The integral method is adopted caculate and analyze to amf three - dimension distruction which is the structure of coil type four - pole and the structure of coil type double - pole and study the size of two kind of electrode structure axial magnetic flux density distribution and its fielduniformity. the finite - element method is used simulate that eddy current has effect on amf when contact tray of douple - pole amf structure is slotted or no

    本文採用積分方法對本文設計的線圈式兩極縱向磁場觸頭結構和線圈式四級縱向磁場觸頭結構的縱向磁場三維分佈進行了計算分析。研究了電弧燃燒期間兩種觸頭結構縱向磁場強度的大小、均勻性，利用有限元法模擬線圈式兩極縱向磁場觸頭結構的觸頭盤開槽和不開槽時渦流對縱向磁場的影響。
  3. Considering the relations between idle load characteristics and armature winding parameters of the salient pole propulsive synchronous motor ( spsm ) with its structure, stator tooth and magnetic saturation, the analysis of numerical method for the back electromotive force calculation of spsm is given under various exciting current values

    摘要針對凸極式同步推進電機的空載特性及其繞組參數與電機結構、定轉子齒槽、磁場飽和等緊密相關的問題，分析了在不同勵磁電流下同步推進電機相反電勢的數值計算方法，提出了採用電機磁場能量微動法計算相繞組的參數，並對一臺十二相同步推進電機的繞組參數及其空載特性進行了計算和測量。
  4. The more poles mode, the unequal pole width mode ; the low - frequency slot harmonic modulation mode and the mode of changing end magnetic conductance are presented, and these designing method can efficiently weaken the end effect and decrease the wave of the thrust

    提出的採用多極電機方式；初級與次級極距不等的方式；齒諧波低頻調制方式和改變電機兩端部磁導的方式等電機的設計原則和方法，都可有效地削弱端部效應，減小推力的波動。
  5. It is tested that the most proficiency method is using pulse - controlled magnet core to generate rotating magnetic field, in which the density and frequency of rotating field can be adjusted, the different form of rotating field can be easily achieved, and both magnetic pole and work piece need not rotate during the magnetic abrasive finishing process

    實踐證明，最有效的方法是脈沖控制電磁線圈的方法產生。這種類型旋轉磁場的強度和磁場的旋轉頻率都可以得到調節，磁場的不同旋轉形式也很容易實現，而且在研磨加工過程中工件和磁極都無需旋轉。
分享友人
分享到 Line

分享到臉書