main strain 中文意思是什麼
main strain
解釋
主應變-
Equal channel angular processing of the pearlitic steel ( 0. 65 wt. % c ) was successfully carried out at 650 with route c in this study, obtaining a total equivalent true strain ~ 5. the microstructure evolution of pearlitic steel in ecap was investigated by means of transmission electron microscope and scanning electron microscope. the main results are as the following : 1
本研究成功地實現了c方式650珠光體鋼65mnecap變形，累積等效真應變達到5 。並用透射電鏡、掃描電鏡研究了珠光體組織的演變特點和滲碳體的變形。主要結果如下： 1 -
Perfect pre - processing and post - processing function is one of the main factors to evaluate the vitality and market value of the finite element analysis system surveying today development of finite element analysis technology, most of which concentrate on establishing fine user interface, also has some limitation on application, and especially, the research on the visualization of arbitrary cut - plane is always in ascendants to realize the visual processing on cut - plane needs reprocessing the results of finite element analysis which have get, so the algorithm is two parts : seeking the physical value of cut - plane and drawing 2d contours, the former, based on the theory of stress on " arbitrary inclined plane " in physical mechanics, use the method of linear interpolation method to get the coordination and physical value of intersection between cut - plane and element arris ; the latter, based on the tables on elements, nodes, stress and strain, summarize a rapid algorithm of generating 2d contours based on the grid. this thesis synthesizes there two parts and get a visual processing program under fortran
縱觀有限元分析技術的發展，目前大多集中在建立良好的用戶界面上的研究仍存在許多應用上的局限性，其中對任意剖面上可視化的研究仍處于方興未艾的階段。要實現任意剖面上可視化處理，必須先將得到的有限元計算結果進行再處理，因此在演算法上分為兩部分：求任意剖面上物理量值的演算法及二維等值線演算法。前一部分以彈性力學中「任意斜截面的應力」為理論基礎，利用線性插值方法得到截面與單元棱邊的交點坐標及交點物理量值；在此基礎上；根據已得到的單元及節點序號表、應力應變物理量表，總結出一種基於有限元剖分網格的快速生成二維等值線的演算法。 -
The main contents are as follows. ( 1 ) filter cloth and the surrounding soil mass are taken as an approximate isotropy in horizontal section, the relationship of stress and strain is studied, the anisotropy is fully considered, the constitutive model of filter cloth reinforcement fly - ash compound is obtained, it is tested with numerous indoor experiments. ( 2 ) the permeable coefficient is introduced into the constitutive relationship of soil mass with relevant seepage theory ( kozeny - carman experience formula ). the test of filter cloth depositing hi the condition of long term seepage flow is done hi the dissertation, the varying regular of permeable coefficient without pressure is presented
本文首先對國內外的研究現狀作了回顧和總結，然後主要針對土工織物加筋粉煤灰復合體的本構關系和計算理論進行研究，主要內容有： （ 1 ）將土工織物和周圍土體視為一種近似的彈性非線性橫觀各向同性體，研究它的應力應變關系，充分考慮它的各向異性，得到土工織物加筋粉煤灰復合體的本構模型，然後通過大量室內試驗進行分析驗證； （ 2 ）引入有關滲流理論，即柯茲尼-卡爾曼（ kozeny - carman ）經驗公式，將滲透系數引進到土體本構關系中。 -
This paper has studied the development of setting & model of the overthrust, which is distributed over the plane & section, and its belting character in the northern margin region of chaidamu basin, and described the character of the main overthrust sheet belt and lower strain area in great details. moreover, it has pointed out a best target for oil / gas exploration on the imbricate fan belt and hidden overthrust forward belt through surveying the developing evolution model and its formation mechanism of the overthrust in the field and structure inversion indoor 6figs., 8refs
研究了柴北緣地區逆沖推覆構造的發育背景、發育模式，平面、剖面展布特徵及其分帶性，並對主幹逆沖斷裂帶及其間的推覆體帶、逆沖席帶和低應變區的特徵進行了詳細描述，同時通過野外觀察和室內構造反演來研究推覆構造的發展演變模式及其形成機理，指出其逆沖疊瓦扇帶和隱伏逆沖前緣帶是最有利的油氣勘探目標.圖6 ，參8 -
G gene of rabies virus m, the of two main regions ( about 1000nt ), ranging from 3161nt to 4162nt and ranging from 4012nt to 4863nt of glycoprotein gene of rabies virus strain m, isolated from mouse in he nan, china were amplified by reverse transcriptase - polynerase chain reaction ( rt - pcr ) in order to complete glycoprotein gene of strain m. these regions were sequenced by the produce of pcr directly. comparison and analysis of nucleotide sequence and amino acid sequence deduced with that of other strains published was performed by computer with dnasisv 2. 5demo software
本研究對我國河南某地野鼠體內分離的狂犬病野毒株mrv基因的3161位? 4162位（ 1001個堿基）和4012位? 4863位（ 851個堿基）片段進行了反轉錄pcr擴增和序列測定，得到mrv的糖蛋白基因全序列，用dnasisv2 . 5demo分析軟體，與已發表的代表性毒株g基因全序列進行核苷酸和氨基酸序列的比較分析，結果表明在同一基因型中， mrv和國際標準攻毒株cvs的同源性最高（ 96 . 5 ） ，和中國減毒株ctn的同源性最低（ 79 . 8 ） 。 -
The main results obtained from this work are as follows : 1. the penicillium. sp ds9701, a strain of degrading phb, was mutagenized by uv treatment
本項工作主要是篩選能高效降解phb的突變株，並對其進行酶學性質的研究，主要結果如下： 1 -
This system provides photo elastic, moire, holographic, speckle technology contained in optical measure strain and displacement analysis software interface, and mainly realizes photo elastic image collection, interference image pretreatment, automatic skeleton extract method, automatic main strain trace protraction method and planar photo elastic image strain analysis function. all the work that the author has done has established a good foundation for more realization of an intact optical measure image strain analysis software system. furthermore, engineer and lab assistant can quickly obtain concise, intuitionistic and quantificational information
該系統提供了光測力學所包括的光彈法、雲紋法、全息法以及電子散斑法等技術應力和位移分析軟體實現的介面，主要實現了等差線圖像和等傾線圖像的採集、干涉條紋圖像預處理、全自動提取光彈條紋圖像骨架線、全自動繪制主應力跡線以及二維光彈應力分析功能，為進一步開發完整的光測力學圖像應力分析軟體奠定了基礎，同時使工程技術人員以及實驗人員能夠迅速的獲取簡明、直觀、定量的信息。 -
We studied the influence of the interface strain and it shows that the lattice mismatch between substrate and film is the main reason of the above observations. expand strain decreases tm - i with increasing resistivity and compressed strain has the opposite effect. using double exchange model of zener these results can be explained qualitatively
27歐姆厘米，轉變溫度是78與154開爾文，磁場強度為7t時，磁阻率為習3及巧6 x結合雙交換模型和不同的應力作用，逐一解釋了產生差異的緣由，其中我們也討論了具有）取向的la 。 -
The main research is below : ( 1 ) the influence to intensity and rigid with corner angle ( 60, 75 and 90 degree ) of crack and the board axes ( 2 ) do a fem stress / strain and crack growth simulation analysis when the corner angle of crack and the board axes is 60 degree ( 3 ) do a intensity resume analysis for the structure which is repaired with a titanium patch in a mechanical way when the corner angle of crack and the board axes is 60 degree through simulation analysis for three failure criterion, we have : ( 1 ) in 60, damage extend quickly with damage analysis in hashin criterion ; it is slower for analysis in maximum stress or hashin - rotem criterion. ( 2 ) in special term ( physical condition incision, shape or maximum load ) the compression strength of the stiffened plate will decline 45 % ~ 50 % under compression loads
通過採用三個不同損傷判據的數值模擬模擬，得到如下結論： （ 1 ）在60時，用hashin判據進行的損傷分析，損傷擴展較快；最大應力及hashin - rotem判據進行的損傷分析，損傷擴展基本相當，且較慢； （ 2 ）在所給加筋板的物理條件、切口大小及形狀、最大載荷等一定的條件下，該加筋板在壓縮載荷作用下，其壓縮強度下降了45 50 ； （ 3 ）在本文提及到的機械連接修理方法以及載荷條件下，修理后的結構強度恢復能夠滿足戰時要求。 -
Relating closely to the main problem of the high sidewall and wide span underground cavities excavation stability of xiluodu hydroelectric project, the evolution characters of geo - stress field in deep - cutting gorge and the whole features of the stress field, strain field and plastic failure zone around the underground chambers after excavation are studied systematically in the dissertation, based on a great deal of data gathered in field investigation and taking the flac3d v2. 0 software as basic computation tools. meanwhile, in the course of research, the new methods of dynamic numerical simulation are summarized and applied. furthermore, the effects of rock mass qualities, initial geo - stress field and excavation procedure on surrounding rock mass stability are discussed
本文緊密結合溪洛渡水電工程大跨度、高邊墻復雜地下廠房洞室群，施工開挖過程中和開挖后圍巖穩定性研究這一重大課題，在詳盡的野外地質調查工作和對大量基礎地質資料的整理與分析基礎上，以目前國際工程地質界公認的最新通用軟體flac ~ （ 3d ） 2 . 0版作為基本計算工具，從整個壩區地應力場的研究開始，通過動態數值模擬分析這一新的模擬思路，系統地研究了深切峽谷區地應力場多階段的特徵和演變規律，進而對左、右岸地下廠房洞室群開挖全過程中圍巖應力場、變形場和塑性破壞區的變化特徵，進行了全過程動態數值模擬研究，並詳細討論了圍巖質量、初始地應力場、施工開挖順序對大型地下洞室群圍巖穩定性的影響。 -
The main purpose of this paper is to study crack growth rate of a class of nonlinear viscoelastic materials under the condition of constant load and small - strain. in this paper : the new test program is raised by referencing the existing test programs and by our trial and error ; in the new test program, facilities involved in the nonlinear viscoelastic crack tests are relatively few, the test process is relatively simple and the data obtained from the experiments are credible. on this basic, the calculation of j integral of nonlinear viscoelastic double cantilever beams specimens and the parameter of fracture work of corresponding nonlinear viscoelasticity are derived
具體成果包括： 1 、證實了雙懸臂梁試件用於非線性粘彈性裂紋擴展實驗研究的優點：雙懸臂梁試件在實驗中能觀測到的擴展過程持續時間比較長，在計算j積分時，計算方法簡單； 2 、得到了改性聚丙烯材料用於非線性粘彈性裂紋擴展實驗的兩種有效的試件構形和相應的試件尺寸；採用不斷改善夾具的方法使得加載穩定； 3 、經過連續四個多月的時間得到了一組有用的實驗數據； 4 、得到了裂紋長度與時間的關系、裂紋擴展速度與時間的關系、裂紋擴展速度與裂紋長度的關系。 -
Through the experiment of the interfacial bonding shear strength and the shrinkage strain of concrete, the influence of the interfacial roughness of used concrete surface and interfacial bonding agent to interfacial bonding strength is revealed ; new concrete component and the shape and size of concrete slab are main factor affecting the shearing stress in layers
試驗結果表明：老混凝土粘結面的粗糙度和界面粘結劑類型對新老混凝土界面粘結強度影響很大；新鋪混凝土材料和混凝土路面板形狀尺寸是影響新老混凝土粘結面收縮剪應力的主要因素。 -
Analysis results of histogram statistics and section electron microscopic scan technique, are that fracture feature of the cracks of the hbbb is similar and the crack is multi - source strain fatigue one. internal defects of the cast, such as impurities, gas holes, etc, are the main causes for early cracks. the contrast analysis of static strength, model and transient respond on three structures with fem proves that geometrical stress concentration in partial area has influence on early crack, also
利用直方圖等統計方法和電鏡掃描技術對該抱軸箱體裂紋分析的結果是：抱軸箱體的裂紋斷口特徵相近，裂紋性質屬于多源性低周疲勞裂紋，鑄件中的夾雜、氣孔等內部缺陷是導致過早裂損的主要原因；利用有限元法對該抱軸箱體三種結構的靜強度、模態和動態響應對比分析，證實了局部幾何性應力集中對過早裂損也有一定影響。 -
Google believes that in the not too distant future, people will be able to translate documents instantly into the world ' s main languages, with machine logic, not expert linguists, taking the strain
谷歌認為，在不太遙遠的將來，人們將能夠翻譯文件，瞬間成為世界的主要語言，同機的邏輯，而不是專家，語言學家，以應變。 -
Furthermore, because of the unique shape of grab and the main frame apply to it, it ' s difficult to calculate the strain of grab with normal linear methods. during the design of grab, the design of holder is the main mission of whole design
在抓鬥斗體的設計中，由於斗底板是整個斗體的主要部分，並且斗底板的結構形狀特殊，所以就更加難以用測試或者計算的方法來求得斗底板的應力。 -
In this article, several existing main compensation methods for the term of dynamic stiffening are reviewed ; describing method of material coordinate is introduced on the basis of the principle theorem of mechanics of continuum ; and the dynamic equation of flexible body is derived from nonlinear green strain tensor and kichhoff stress tensor, which are based on initial configuration
本文評述了現有的幾種主要的動力剛化項補償方法，根據連續介質力學的基本原理，引入物質坐標的描述方法，採用基於初始位形的非線性green應變張量和kichhoff應力張量推導柔性體的動力學方程。 -
The main research works done and conclusions extracted are listed as follows. ( 1 ). based on the piezoelectric equation, the strain and stress distribution are analyzed for the composite material structures with piezoelectric materials embedded inside
從壓電材料的壓電方程出發，針對埋入式壓電片，分析埋入式壓電片在和結構一起發生變形時基體結構材料和壓電材料的應力應變的分佈規律和關系。 -
Diaminopimelic acid in the cell walls of actimomycetes was most meso - dap. main menaquinones were mk - 9 ( h6 ), mk - 9 ( h8 ) of nocardiopsis. strain 10001 was mk - 9 ( h2 )
對部分放線菌的全細胞壁氨基酸組分的測定發現，多數菌株含有meso - dap ，為稀有放線菌。 -
3. the two stages of primary creep and steady - state creep of 3d c / sic correspond to the gradual saturation of matrix crack and the opening of these cracks respectively. the transverse crack is the main contributor to the macroscopic creep strain of 3d c / sic, and its opening is controlled by the creep temperature
（ 3 ） 3dc sic復合材料的減速蠕變階段和穩態蠕變階段分別對應著基體裂紋趨于飽和和逐漸張開這兩個過程；橫向基體裂紋是3dc sic復合材料宏觀蠕變應變的主要貢獻者，溫度是影響橫向裂紋張開速度的一個重要因素。 -
He not only belongs to the english school, but his ir theory also constitutes an important part of the main strain theories of the us ir
他屬于英國學派，但也是美國主流國際關系理論體系中的一部分。
分享友人