member in tension 中文意思是什麼
member in tension
解釋
受拉構件-
Here the hsc of sompa is achieved through adding super - effective water reducer, fined slag and silicon fume, and decreasing the water / cement ratio. by varying the area ( spacing ) of tension bars, compressive bars, vertical links and distribution steel and embedding steel fiber and polypropylene fiber we try to improve the behaviors of reinforced high performance concrete one - way spanning slabs in bending, so that its ductility be greater than 5. with the same arrangement of steel the width of bending member is varied to observe the effect of the width / depth ratio on the ultimate compressive strain of concrete
通過變化受拉筋含筋率和受壓筋、箍筋（鉤筋、分佈筋）含量，或摻加纖維使之成為鋼纖維高強混凝土（ sfrhsc ）和聚丙烯纖維高強混凝土（ pfrhsc ） ，對高強混凝土雙筋截面梁、板的受彎性能進行了試驗研究，試圖改善高強混凝土受彎構件的延性，使其延性比大於5 ；並在相同配筋情況下，通過變化截面寬度，研究了高強混凝土受彎構件的寬高比對壓區混凝土極限應變的影響；並對試驗構件的裂縫發展情況進行了觀測。 -
It is determined that with accurate knowledge of the complete stress - strain curve of concrete in compression, steel in tension, and with an iterative computerized non ? linear method, it is possible to predict the entire moment - curvature, moment - flexural rigidity and axial rigidity relation ship of a cross - section of a structure member
可以確定，只要知道混凝土受壓和鋼筋受拉的完整的應力應變關系，採用選代的非線性計算方法，就有可能預測結構截面彎矩一曲率、彎矩一彎曲剛度和軸向剛度的關系。 -
The results of full - scale tests in this dissertation canaugment international database of test and numerical analysis results for tubularjoints. based on the experimental study and numerical analysis, design proposal for theultimate tensile strength of gusset plate connections to slotted tubes is recommended. it has bigness significance to establish design formulae of gusset plate connections toslotted tubes and perfect design formulae of steel tension member and it also can givesome advices to practice engineering
在試驗研究的基礎上，根據有限元分析的結果，本文提出了關于管板節點受拉極限承載力的設計公式，為我國鋼結構規范建立管板節點受拉極限承載力設計公式及有關拉桿的設計公式的進一步完善提供了有意義的參考，同時對實際工程也有一定的參考價值。 -
A way to avoiding crack or reducing crack width of concrete or reducing distortion of member is using prestressed concrete. the writer tried to make full use of the merit of the prestressed concrete and designed prestressed concrete mandril to control crack of structure. the prestressed concrete mandril, which was firstly applied high pressure on a small concrete bar, and then was made in concrete, so it would act as reinforced bar and resist load. in this thesis the writer designed 24 mmnbers and had experimental study of them, reached the conclusion that the effect of resisting crack of the prestressed concrete mandril was good when the load was not large, it can enhance the capacity of resisting crack and reduce the crack distance and crack width, but when the loads was large, the effect of resisting crack was not good, when we used the prestressed concrete mandril and reinforced bar together in member, the effect of resisting crack was very good. the writer analysed the adherence mechanism and wreck mechanism of the prestressed concrete mandril in anxial tension members, and according to the character of the prestressed concrete mandril, the writer constructed the bond model of it. then the writer introduced the analysis theory of crack including the bond - slip theory, the non - slip theory, the synthesis theory and mathematics stat method. the different theory had different theory base, they considered that the primary affection of crack width was different. in this test, the crack distance and crack width of members which placed reinforced bar were match to the compute value of the code gb 50010 - 2002 very well. to the members which
本文共進行了24根試件的試驗研究，得出了預應力混凝土芯棒能較大地提高構件抗裂承載力，在荷載小於預應力混凝土芯棒的開裂荷載時有較好的抗裂效果，能較大地減小裂縫間距和裂縫寬度，但是當荷載較大預應力混凝土芯棒開裂時預應力混凝土芯棒的抗裂效果不是很好，若將普通鋼筋和預應力混凝土芯棒一起使用時則有很好的抗裂效果。本文分析了預應力混凝土芯棒在軸拉試件中的粘結機理和破壞機理，根據預應力混凝土芯棒本身的特點，提出了預應力混凝土芯棒與后澆混凝土之間的粘結模型。然後本文詳細介紹了經典的裂縫分析理論粘結滑移理論、無滑移理論、綜合理論和數理統計方法，各理論有著各自不同的理論基礎，認為影響裂縫寬度的主要影響因素也各不相同。 -
Conti synchroforce heavy - duty timing belts are available in the tooth profiles htd and std and are manufactured in two versions, i. e. as cxpiii with a glass cord tension member for high dynamic demands, and as cxa iii with an aramid tension member for high torques
Contisynchroforce高性能同步帶按齒形有htd和std 。由玻璃線繩作張力層的cxp111運用於高功率傳動，而由芳輪線構成張力層的cxa111運用於高扭矩傳動。 -
2. for frame supported double - short - pier shear wall under vertical loads, the non - noding area of transfer beams turns into a member of flexure and tension with small axial force, and bending stress dominates in the stress distribution on the cross - section. in the nodding area, the axial force increases while the bending effect is small
2 、框支雙肢短肢剪力墻在豎向荷載作用下，轉換梁的非節點區為一拉彎構件，軸向拉力較小，截面的應力分佈以彎曲應力為主;在節點區，軸向拉力效應增大，而彎曲效應很小。
分享友人