membrane porosity 中文意思是什麼

membrane porosity 解釋
薄膜孔隙性
  • membrane : n. 1. 【解、生】（薄）膜，隔膜。2. 〈古語〉（古文件的）（一頁）羊皮紙。-braneous , -branous adj. 膜（狀）的，膜質的；隔膜的。
  • porosity : n. 1. 多孔性。2. 【物理學】孔積率；孔度，隙度。3. 多孔部分；多孔結構；多孔的東西。
  1. The present work indicates the organic nf membranes and the inorganic nf membranes all have shortages, so develop composite nf membranes that have low cost, mechanically strong and thermally / chemically - resistant, easy to cleanout and good performances is a very important task. in this paper, the preparation of inorganic - organic composite nf membranes were presented. this composite comprise a porous sio2 / al2o3 support substrate, the pore diameters of which ranging from 10 to 15 nm, this inorganic support substrate having a polymer membrane which comprises an polyvinyl alcohol ( pva ) or polyamide ( pa ) densely deposited on at least one of the face surfaces thereof, the structural porosity of such pva and pa membrane ranging from 3 to 5 nm

    本論文以開發無機?有機復合納濾膜為出發點，首先在al _ 2o _ 3多孔微濾膜上利用溶膠?凝膠法制備sio _ 2 al _ 2o _ 3無機復合超濾膜作為無機?有機復合納濾膜的基膜；選用聚乙烯醇和聚酰胺為表面功能層材料，分別探討了以羥基丁二酸和磺基水楊酸為混合交聯劑，採用浸塗法制備了聚乙烯醇sio _ 2 ? al _ 2o _ 3復合納濾膜；以均苯二甲酰氯、哌嗪和二胺為單體，採用界面聚合法制備了聚酰胺sio _ 2 ? al _ 2o _ 3復合納濾膜，並對影響膜性能的諸多因素進行系統研究。
  2. Fabricating the nanoporous silicon membrane with nanotechnology and bio - mems technology, the thickness of membrane, pore size and distribution, geometry shape and porosity can precisely controlled

    摘要採用納米技術和生物微電子機械繫統技術制備納米多孔硅膜，可準確控制膜的厚度、幾何形狀、孔大小、孔分佈和孔隙率。
  3. The effect of thermal conductivity of membrane on the distribution of temperature in the fuel cell is discussed, and the effect of inlet velocity and porosity of porous diffusion layers on the fuel cell performance are analyzed

    討論了質子膜的導熱率對電池內溫度分佈的影響。分析了進料速度和多孔擴散層孔隙率對電池性能的影響，結果表明較快的進料速度和較大的擴散層孔隙率都能有效提高電池的性能。
  4. The membrane layer is formed by the vacuum forming technology. by controlling the weight and the ratio of long path of ceramics fiber, changing the operation factor reasonably of vacuum forming, we can obtain the ceramic fiber composite membrane layer, which has pore diameters of about 5 to about 30um, porosity i s 50 - 80 %, and tensile strength is about 4. 1to 18. 1mpa and thickness of membrane layer is 0. 5 - 2 mm, has the good thermal shock resistance and peal off

    膜層採用真空抽濾成型工藝，通過控制膜組分中陶瓷纖維長徑比、纖維加入量、成型時料漿濃度、成型壓力及成型時間等可以獲得膜孔徑5 ? 30 m 、氣孔率50 ? 80 、抗折強度4 . 3 ? 18mpa 、膜層厚度0 . 5 ? 2mm 、具有良好熱性能和耐剝離性能的陶瓷纖維復合微濾膜材料。
  5. As the pre - evaporation time increases, the holes on the membrane surface becomes smaller and less, dense layer is becoming more evident with large and deep holes in supporting layer ; and porosity increases as well - as average hole diameter decreases

    隨著預蒸發時間的延長，膜表面的孔變小變少，膜的緻密層越來越明顯，支撐層有大而深的孔結構出現。隨著預蒸發時間的延長，膜的孔隙率上升，平均孔徑下降。
分享友人
分享到 Line

分享到臉書