meshing condition 中文意思是什麼
meshing condition
解釋
嚙合條件-
On the condition of “ many - head ” and “ small drive ratio ” ， the plane double enveloping hourglass worm can not settle the problem of undercutting and sharpening simultaneously. it has devoted to a new type hourglass worm _ sphere double enveloping hourglass worm. the coordinate system is established according to the frock. the meshing equation and the tooth equation of worm and gear have been developed and the distribution of contact line on gear tooth is analyzed. to evaluate the meshing quality ， four meshing quality indexes and five original parameters are put forward. through mass programming computing ， the relations between meshing quality and original parameters are derived and depicted by graphs
考慮到平面二次包絡環面蝸桿傳動在多頭小傳動比條件下根切與齒頂變尖的矛盾很難同時解決且嚙合性能較差，介紹了一種新型環面蝸桿傳動? ?球面二次包絡環面蝸桿傳動.在研究過程中，根據工裝建立了坐標系，根據一二包過程的運動關系推得了嚙合方程和蝸桿與蝸輪的齒面方程，分析了蝸輪齒面上的接觸線分佈.為了評價嚙合性能，提出了4項性能指標和5項原始參數，通過大量編程計算得到了嚙合性能指標與原始參數之間的關系，並以圖表直觀的表示 -
On the condition the trapping characteristics of whole profile meshing helical pump are lucubrated by theory for the first time, and the select range of the helical angle that can eliminate completely the trapping of whole profile meshing helical gear pump is also obtained
在此基礎上，首次對全齒廓嚙合斜齒齒輪泵的困油特性進行了詳細的理論研究，得到了完全消除全齒廓嚙合斜齒齒輪泵困油沖擊的螺旋角的選擇范圍。 -
The researchful results indicate that the flux pulse ration of ordinary helical gear pump without clearance is less than that of the gear pump with clearence under the condition that the main parameters are same, and the flux pulse ration of ordinary helical gear pump is less than that of whole profile meshing helical gear pump
研究結果表明：在主要參數相同的情況下，普通斜齒齒輪泵無側隙時流量脈動率小於有側隙時的流量脈動率；全齒廓嚙合斜齒輪泵比普通斜齒輪泵的流量脈動略小。 -
Equations of mesh, shorting contact line, undercutting limit line, meshing limit lines and the existence conditions, angle between the direction of relative speed and the direction of contact line, induced normal curvature about every point on the contact line are established. moreover, the paper also theoretically analyzed the error of the grinded gear surface. on the basis of the theory, the computer program is worked out to automatically produce the contact line and the boundary curves of mesh. analysis of meshing circs under different parameters can be done so that we can gain the best process condition
首先對漸開面二次包絡理論進行了深入的探討，推導出了兩次嚙合的嚙合方程式、瞬時接觸線方程式、根切界限線方程式、嚙合界限線的方程式及其存在條件，相對運動速度方向與接觸線方向的夾角及接觸線上各點的誘導法曲率；此外，還對磨齒后工件的齒面誤差進行了理論分析；並在理論基礎上編制了相應的計算機程序，自動生成接觸線族及嚙合界限線，對不同參數條件下的嚙合情況進行分析，可以使工藝條件達到最佳狀態；最後研究了磨齒裝置，設計了磨齒機的傳動系統。 -
Tooth surface equations and contact line equations of the involute worm gearing are established according to its machining methodology. meshing characteristics in rigidity condition are studied. these characters include the inductive normal curvature along the contact line on the worm surface, the first and the second limit lines during the engage of the worm gear, and the influence of the intersect angle between the contact line the relative velocity of the worm and the gear on transmission performance
根據漸開線圓柱蝸桿傳動的創成方法，建立了漸開線圓柱蝸桿和蝸輪的接觸線方程式、齒面方程式，分析了漸開線圓柱蝸桿傳動的剛性嚙合特性，如蝸桿與蝸輪嚙合時的誘導法曲率、一類界限曲線、二類界限曲線和蝸桿與蝸輪間相對速度方向和接觸線方向的夾角對傳動性能的影響； 2 -
At first the paper begin to study the foundation of digital curved face and space meshing principle, introduce the basic knowledge of curve theory and curved face theory, explain the mathematical tools of vector turning and coordinate conversion in the paper ; analyse the motion and relative motion of rigid body, provide the condition of gear driving continuous contact and equation of conjugate meshing
論文首先從參數化曲面和空間嚙合原理基礎出發，介紹了曲線論和曲面論的基本知識，對課題研究重的數學工具矢量回轉和坐標變換進行了說明;分析了剛體的運動和相對運動，根據空間嚙合原理給出了輪齒傳動連續接觸的條件和共軛條件方程。 -
Then experiment was processed to testify the calculated results. based on the theory of vibration mode, harmonic response and experiment, fea meshing, fea element and bound condition of expansion joint were analyzed. then a parametric fea modeling & post process software was developed by apdl and visual basic langrage
本文採用有限元數值分析方法，利用大型商用有限元計算軟體ansys ，研究了基於結構參數化設計思想的波紋管膨脹節的振動模態和含波紋管膨脹節管系的振動響應分析方法，開展了波紋管膨脹節模態試驗驗證。 -
By analyzing the vibration movement of the gear system, the actual center - line equation and that of the theoretic meshing line were derived in their vibration condition, and their movements and the modality of the actual meshing line was analytically verified
摘要根據齒輪系統的振動運動，建立了在振動條件下齒輪副實際中心線方程和理論嚙合線方程，分析論證了實際中心線和理論嚙合線的運動及實際嚙合線的形態。 -
Firstly, the paper introduces the development and application of computer graphics & image technique, discusses the principle and method of cg and digital image processing, such as matrix of the graphic transformation, homogeneous reference frame, sampling and quantization of the image, file format of the image, template operation, etc. secondly the paper introduces the purpose and method of image enhancement processing, explains the each occasion of those methods such as threshold transformation, smoothing processing, sharpening processing, analyzes and contrasts the processing results of object image. thirdly, the paper introduces the method of mathematics morphologic, edge detection and thinning processing, attains character description of image and character dots of the contour. fourthly, the paper processes the coordinate transformation to character dots and basic splines fitting, imports correlative condition to devise meshing line and meshing track
本文首先介紹了計算機圖形圖像技術的發展與應用情況，對計算機圖形學和數字圖像處理的一些基本理論和方法如圖形變換矩陣、齊次坐標系、圖像采樣和量化、圖像文件格式、模板操作等內容進行了討論：然後對圖像增強處理的目的和方法進行了介紹，對諸如閥值變換、平滑處理、銳化處理等方法的應用場合進行了說明，並對實物圖像的處理結果進行了分析與比較；接下來介紹了數學形態學方法、對增強后的圖像進行邊緣檢測的方法和圖像的特徵描述方法，並獲取輪廓的特徵點：隨后對獲取的特徵點進行坐標變換，並進行b樣條曲線擬合，引入相關條件生成齒輪副的嚙合線及嚙合軌跡：最後引入等值線和區域填充表示方法，並以等值線和區域填充的形式對弧齒錐齒輪嚙合模擬的載荷分佈情況進行了直觀的表示。 -
Attention must be paid to the selection of meshing grid, appropriate simplification of the boundary condition, and selection of turbulent model and solving algorithm when general cfd soft - ware is empoyed
在用通用cfd軟體時，要注意的是網格的確定，邊界條件的簡化，模型以及演算法的選擇。 -
The different calculative formulas for meshing efficiency of drive in different condition are deduced. the deep analyses of pressure angle in cycloid steel ball planetary transmission are presented
從理論上研究分析了擺線鋼球行星傳動的嚙合效率，推導了不同情況下擺線鋼球行星傳動嚙合效率的計算公式。
分享友人