meter calibration 中文意思是什麼

meter calibration 解釋
計量器校準
  • meter : n. 1. 測量儀表，計量器；計，表。2. 計量人；計量官。vt. 用表計算[測量、記錄]。n. 〈美國〉＝ metre.
  • calibration : n. 1. 測定口徑。2. 刻度，標度，劃度數。3. 校準；標準化。
  1. Calibration specification for electronic level meter

    電子水平尺校準規范
  2. We write the program which used for fighting errors in absolute positioning. we also write the program which used for linear combinating in absolute positioning. from analyzing for the measurement of outer, we can conclude that we can use m estimation to estimate parameter in gps absolute positioning. lt has application value. using it, we can obstain the stable positioning result and remove the outer. in this paper, we calculate the data which from the baseline space of the gps calibration space. we also draw some conclusion using broadcast ephemeredes and smoothing pseudoranges. the positionging precision is in 1 - 2 meter

    編制了gps絕對定位中抗差估計程序和應用線性組合進行單點定位的程序。通過對粗差量級的分析，得出在gps觀測量存在粗差時， m估計是有其應用價值的，它使定位結果較為穩定，減弱和剔除了粗差的影響。應用線性組合程序對gps綜合檢定場數據基線網點進行計算，得出用廣播星歷和平滑后的偽距可以給出較好的結果，點位精度在1 ? 2米。
  3. This meter shall be capable of maintaining this accuracy for an adequate period, and the calibration frequency set accordingly

    這個表應能保證其準確度在一定內時間都不變，其校準周期同火花機。
  4. It is suitable to be used as precise inductance standard for all kinds of metrology units, research institutes, and manufacturers, and especially suitable for on - site lcr meter calibration

    適用於各計量、科研與生產部門作精密電感標準，尤其適用於對lcr表進行現場校準。
  5. Abstract : a combined formula of the constant speed sampling flow is induced through the calibration of a flow meter, the correction of a calibrated flow and the derivation of a real flow

    文摘:通過對流量計的校準、校準流量的修正和真實流量的推導，歸納出等速采樣流量的綜合算式，並運用程序計演算法進行快速、準確地計算，真正實現等速采樣。
  6. Main products : to be responsible for the transfer of a quantity value ( includes optics measurement ) ; calibration of measuring instruments and meters, as well as measuring products ' s pattern evaluation and sample test, calibration device of heat meter

    負責天津市計量基、標準的量值傳遞計量儀器、儀表的校準，計量產品的定型鑒定和樣機試驗。
  7. In order to improve measurement precision and display fidelity of the instrument, three new methods of nonlinear calibration of thermal instruments, which are based on intelligent control theory, are presented in this paper, such as nonlinear compensation of zr02 oxygen measurement instrument using bp nn, nonlinear calibration of temperature measurement sensors using cmac nn and nonlinear identification of throttle flow meter using ga. these methods prove to be not only simple but also effective

    火電廠熱工儀表普遍存在非線性特性，為了提高參數測量的準確度和儀表顯示的精確度，基於智能控制理論，文中提出了熱工儀表非線性校正的新方法： bp神經網路補償氧化鋯氧量計非線性特性的方法、 cmac神經網路校正測溫傳感器非線性特性的方法、遺傳演算法辯識節流式流量儀表非線性特性的方法。
  8. Development of calibration system based on can bus for combined meter in automobile

    總線的汽車組合儀表校驗系統的設計
  9. Calibration will be made by applying appropriate sinusoidal voltage and current signals with known phase relationship to the meter under test. the ranges of test voltages and currents are 25 v to 250 v and 50 ma to 100 a respectively

    按已知的相位關系，將適當的正弦電壓及電流訊號加於接受測試的功率因數表，以進行校正。測試電壓及電流量程分別為25v至250v及50ma至100a 。
  10. Road construction and maintenance equipment. calibration and verification of the on site settings of the continuous dosing apparatus of material production units. part 1 : belt flow meter for belt conveyor

    道路建設及養護設備.物質生產單位的連續配製設備的現場裝置的校正及檢驗
  11. Several central modules in system design were introduced. the examination, parameter read - in and the unit calibration of the combined meter board were implemented, suiting for kinds of digital instrument

    摘要論述了系統設計中的幾個主要模塊，實現了組合儀表總成校驗、參數寫入及電路板檢測，該系統適合各類數字儀表檢測。
分享友人
分享到 Line

分享到臉書