mirror cell 中文意思是什麼
mirror cell
解釋
鏡室-
The research result indicated : for the strip primary mirror discussed in this article, the hexagon light - weighted cell has the best structural rigidity quality, the square cell is a little worse, the triangle cell is the worst ; there is an optimum on primary mirror thickness ; on condition of 1g gravity load combining with 4 centigrade uniform temperature rising, the thinner and higher of the flexible support reed, the better of the primary mirror surface figure. the decision of the structural parameters of the flexible support reed must take static rigidity, dynamic rigidity, static strength and dynamic strength of primary mirror assembly into account
研究結果表明：對于本文的長圓形主鏡，採用正六邊形輕量化孔，鏡體結構剛性品質最好，正方形次之，正三角形最差；主鏡鏡體厚度存在最佳值；主鏡組件在1g重力、均勻溫升4共同作用的工況下，主鏡柔性支撐簧片厚度越小、高度越高，主鏡綜合面形誤差（ p - v值）越小，但同時主鏡組件的剛體位移增大、固有頻率下降，因此柔性支承結構參數的確定要綜合考慮主鏡的綜合面形誤差和主鏡組件靜態剛度、動態剛度、靜態強度和動態強度等因素。 -
Under mirror obviously ; the cell apoptosis divides into the early stage, the intermediate stage, stage of formation of apoptosis body and the later period stage ( three issuses of four stges ), its ultrastructure is mainly observed the cellular form, the cytoblastema, the nucleus, the chromatin change, the special sign of cell apoptosis - apoptosis body
鏡下可見：細胞凋亡分為早期階段、中期階段、凋亡小體形成階段和晚期階段（ 3期4階段） ，其超徽結構主要可見到細胞形態、胞漿、胞核、染色質的變化，及細胞凋亡的特異性標志凋亡小體。 -
The coordinate systems and time systems are described in detail at first, then the paper presents the whole algorithm containing line of sight generation and projection attitude data combination scan mirror calibration, find corresponding grid cell, resample. at the same time, scan gaps and detector delays are analyzed in detail
論文首先對校正過程中用到的時間系統和坐標系統作了介紹，然後給出了完整的校正演算法，包括視線產生和投影、姿態合成、掃描鏡校正、尋找校正圖像空間像素到未校正圖像空間的對應像素位置、重采樣這幾個部分，並在相鄰掃描行間隙的插值上採用了簡潔的方法。 -
The electricity mirror observation profit lung drinks the inductin lung cancer cell apoptosis
摘要電鏡觀察益肺飲誘導肺癌細胞調亡。 -
That is, by the calculation of the anti - thermal deformation quality factor and synthetic quality factor of some typical primary mirror materials, the primary mirror material is selected scientifically and rationally. by the finite element method and the conception of structure rigidity quality factor, researching the relation between the light - weighted cell shape, the mirror thickness and mirror structural rigidity quality. by the force - thermal coupling analysis of the primary mirror assembly, the relations between the thickness, height of the flexible support reed and primary mirror synthesis surface figure error ( p - v ) have been researched
即，通過對常用主鏡材料的抗熱變形品質因數和綜合品質因數的定量分析，科學地完成了主鏡的選材；應用有限元分析方法，藉助于結構剛性品質因數的概念，研究了主鏡輕量化孔的形狀和主鏡厚度對鏡結構剛性品質的影響；通過對主鏡組件的力熱耦合分析，研究了主鏡柔性支撐簧片厚度與高度對主鏡面形的影響。 -
( 3 ) properties of yag laser q - switching by sbs were experimentally investigated, and the laser without back reflective mirror was devised, and laser pulse was obtained at repetition rate ihz and 5hz by optimizing lens focal length, length of cell and position of lens focal. point, resulting quality of pc is ideal
（ 4 ） 、實驗研究了sbs的yag激光器，設計了無後向反射鏡的sbsyag激光器。在泵浦能量17j 、重復頻率分別為1hz 、 5hz時，得到穩定輸出的能量為19mj 、脈寬為10 . 7ns 、光束質量很好的激光脈沖。
分享友人