molten condition 中文意思是什麼
molten condition
解釋
熔融狀態-
Abstract : hydrogen and oxygen solubility in molten copper, condition of gas - absorption during smelting of pure coper, mechanism of gas hole formation, gas hole appearance on worked material and measure to gas absorption prevention have been briefly described
文摘:論述了氫和氧在銅液中的溶解能力、熔鑄紫銅時的吸氣條件、氣孔形成的機理、氣孔在加工型材上的表現、防止吸氣的措施等。 -
It ' s pointed out that, under the condition of vim refining, the amount of oxide inclusions residue in molten steel increases with the increased loss of deoxidizing elements, and the key of melting extra - low oxygen steel is to avoid the thermal decomposition of lining material ; the size of deoxidizing products increases with the increased degree of supersaturation of deoxidizing elements ; larger inclusions granules found in extra - low oxygen steel come mainly from lining material
結果表明，在真空感應熔煉條件下，殘留在鋼中的氧化物夾雜數量隨脫氧元素鋁燒損量增加而增加，熔煉超低氧鋼的關鍵是避免爐襯熱分解；脫氧產物尺寸隨脫氧元素過飽和度增加而增加；超低氧鋼的大顆粒夾雜主要來自爐襯材料。 -
Sintering speed increased greatly with the help of great quantity of heat of the molten iron, the great quantity of heat sent out from the carbonizing reaction and a little quantity of liquid, this sintering type is an instantaneous sintering, the sintering compacting can carry completely in a few minutes, the degree of sintering compacting is very high. ( 6 ) the vc - fe surface composite has high rigidity, it ' s rigidity exceeds 60hrc, under condition of dry sliding friction and overloading
鑄造燒結時，過熱鐵水的巨大熱流密度沖擊、粉料壓坯中的碳化反應的放熱以及壓坯中少量液相的產生使壓坯的燒結速度大大提高，此時屬瞬間液相燒結，在十幾分鐘內燒結過程即可完成，可達到很高的緻密化程度。 （ 6 ）鑄態下vc一fe表面復合材料具有很高的硬度，其鑄態硬度） 60hrc 。 -
Abstract : according to the character and actual condition of rh in shanghai baogang, molten steel flow in ladle and its effect on decarburization were studied with a three dimension turbulent flow and concentration modelling. the results show that, within a certain range, the decarburization rate increases not only with the increase of snorkel diameter and ar fluid flow but also with the decrease of the immersed depth of the snorkel
文摘:根據上海寶鋼rh的特點和實際情況，建立了三維流場、濃度場程序，對鋼包內鋼水的流動、處理過程的脫碳進行了研究，並對它們的影響因素進行了分析.結果表明，在一定范圍內增加循環管直徑和吹氣流量、減小浸漬管浸入深度有助於提高脫碳速度 -
In this section, a small organic molecule is applied to instead of pzt with the purpose to avoid the rigidity difference between cpe and pzt. ( 1 ) there is no plateau area in the conductivity curve of cpe / pzt / vgcf composite, which is due to the molecular level blending of cpe and zkf in molten condition during the preparation of cpe / zkf / vgcf composites, further verifying that pzt is conducive to the formation of conductive loop
通過對cpe / zkf / vgcf復合材料的分析探討得出: （ 1 ） cpe / zkf腳gcf復合材料的導電曲線上並不存在類似cpe / pzt渾gcf復合材料的半導區平臺，這是由於cpe億kf / vgcf復合材料的制備是在cpe和zkf熔融的狀態下的分子水平的共混，進一步證明了pzt對導電迴路形成的雙重作用;同時，由於zkf對vgcf的包覆作用，使cpe億kf那gcf復合材料導電臨界值較高。 -
The wounded state mentioned with molten fury means having health at 20 %, same as the condition for using warrior ' s execute
火焰之怒（對受傷目標造成外傷害那個）效果里的受傷目標意味著對方的血低於20 % 。 -
Influence of sintering condition on microstructure and dielectric property of 0. 8pmn - 0. 2pt ceramics by molten salt synthesis
陶瓷的燒結條件對其顯微結構和介電性能的影響
分享友人