molybdenum disulfide 中文意思是什麼
-
Molybdenum disulfide for industrial use
工業二硫化鉬 -
Then the molybdenum disulfide nanoparticles which size was in the range of 20 - 30 nm were prepared by the desulfuration of molybdenum trisulfide if taking hydrogen as a protection atmosphere at some temperature. the mos2 nanoparticles were then characterized by x - ray diffraction and transmission electron microscope. the mos2 nanoparticles and commercial common mos2 particles ( c. a
將乾燥后的三硫化鉬粉末在氫氣保護氣氛條件下，加熱脫硫得到粒徑在20 30nm之間的納米二硫化鉬顆粒，用x射線衍射儀（ xrd ）和透射電子顯微鏡（ tem ）對二硫化鉬納米顆粒進行了表徵。 -
After looking up a large amount of native and foreign information, the materials used in the experiment were as follows : ptfe base, graphite filler, molybdenum disulfide filler, copper powder filler, carbon fiber and so on. the experimental method is that the formula was designed according to uniform experimental method, the relationship between formula and frictional property was found with spline function and then the representative test points were chosen from fitting curve to make verification test for optimization. the preparative technique of solid lubricant is cold - press sintering method
經過查閱大量國內外文獻資料后確定原料為：聚四氟乙烯樹脂為基體，加入石墨、二硫化鉬、銅粉、碳纖維等填料；試驗方法為：根據均勻試驗方法設計配方，用樣條函數找出配方與摩擦性能的關系，然後在擬合曲線上選取具有代表性的試驗點進行驗證試驗，達到優化的目的；制備工藝：冷壓燒結法制備固體潤滑劑。 -
Steel fiber, molybdenum disulfide. iron powder, iron wire netting. steel wire rope and synthetic fiber lift belt, precision casting products
鉬粉鋁粉鐵屑鋼纖維鋼絲繩及吊帶 -
With the reference of many relevant materials, the author prepared a fined molybdenum disulfide powder with a average size of 800nm by ball milling, and a nano - copper with average size of 30nm in micromulsion solution method, and synthesized surface - modified titanium dioxide nanoparticles with average size of 40nm in organic media via sol - gel method. the tribological performances of three particles were studied by universal test as well, with the result of fined molybdenum disulfide powder with good reducing wear and antiwear performance at low load, nano - copper with good reducing wear and antiwear performance at high load, surface - modified titanium dioxide nanoparticles maintaining stable reducing wear and antiwear performance from low load to high load due to its characteristics of organic and inorganic nanocomposite. the results indicate that the nanocomposite is the most perspective oil additive. the reducing wear and antiwear mechanism of nano oil additive was studied with in - situ tribochemical principle. nano additives possess broadly developing prospect with its above - mentioned performance
在參閱了大量文獻的基礎上，分別採用了球磨法、微乳液法、溶膠?凝膠法制備了超細二硫化鉬、納米銅粒子、表面修飾納米二氧化鈦，經原子力顯微鏡測試，獲得的超細二硫化鉬的粒度平均在800nm以內，納米銅粒子平均粒度約為30nm ，表面修飾納米二氧化鈦平均粒度約為40nm ，在萬能摩擦磨損試驗機上測試了三種粒子的摩擦學特性，結果表明：在合理的添加濃度范圍內，超細二硫化鉬在低載時具有優良的減摩抗磨性能，納米銅在高載時具有比較好的減摩抗磨性能，表面修飾二氧化鈦粒子因具有有機與無機復合物的特性，從低載到高載都保持穩定的減摩抗磨性能。 -
Mc nylon molybdenum disulfide
Mc尼二硫化鉬 -
Made of high - speed mixing polytetrafluoethylene resin and a certain volume of filling agent ( such as carbon fiber, graphite, molybdenum disulfide, glass fiber and bronze powder etc. ) shaped by moulding then through high heat sintering
用聚四氟乙烯樹酯與一定量的填充劑（如：碳纖維、石墨、二硫化組、玻璃纖維、青銅粉等）經高速混合均勻後用模塑成型經高溫燒結製成。
分享友人