no-load characteristic 中文意思是什麼

no-load characteristic 解釋
空載特性曲線
  • no : adj 1 〈加在單數名詞前,相當于冠詞 a an 的否定形式〉(一個也)沒有。 Is there a book on the table...
  • load : n 1 裝載,擔子;負擔;工作(負荷)量。2 (車船等的)裝載量;一馱,一車,一飛機。3 【電、機】(機...
  • characteristic : adj 有特性的;表示…特性的,…特有的。 Japan s characteristic art 日本特有的藝術。n 特性,特徵,性...
  1. No - load characteristic test

    空載特性試驗
  2. On - line monitoring of hvcb is the precondition of predicting maintenance, is the key element of reliable run, and is the important supplement to the traditional off - line preventive maintenance in fact, the faults are made by hvcb, no matter in number or in times, is over 60 % of total faults so it has determinative importance for improving the reliability of power supply and this can greatly decrease the capital waste used by - dating overhaul in this paper, the inspecting way of hvcb mechanism characteristic is discussed the concept of sub - circuit protector is presented, the scheme that we offered has been combined with sub - circuit integrality monitoring theory, to ensure that it has the two functions as a whole according the shut - off times at rated short circuit given by hvcb manufacturer, the electricity longevity loss can be calculated in each operation, and the remained longevity can be forecast too an indirect way for calculating main touch ' s temperature by using breaker shell temperature, air circumference temperature and breaker ' s heat resistance is improved in this paper, and main touch resistance can be calculated if providing the load current msp430, a new single chip microcomputer made by ti company, is engaged to develop the hardware system of the on - line monitoring device, and special problem brought by the lower supply voltage range of this chip is considered fully

    高壓斷路器所造成的事故無論是在次數,還是在事故所造成的停電時間上都占據總量60以上。因此,及時了解斷路器的工作狀態對提高供電可靠性有決定性意義;並可以大大減少盲目定期檢修帶來的資金浪費。本文論述了斷路器機械特性參數監測方法;提出了二次迴路保護器的概念,並將跳、合閘線圈完整性監視和二次迴路保護結合起來,給出具有完整性監視功能的二次迴路保護器實現方案;根據斷路器生產廠家提供的斷路器額定短路電流分斷次數,計算每次分閘對應的觸頭電壽命損耗,預測觸頭電壽命;提出根據斷路器殼體溫度和斷路器周圍空氣溫度結合斷路器熱阻來計算斷路器主觸頭穩態溫升的方法,並根據此時的負荷電流間接計算主觸頭迴路的電阻;在硬體電路設計上,採用美國ti公司最新推出的一種功能強大的單片機msp430 ,並充分考慮該晶元的適用電壓范圍給設計帶來的特殊問題;在通信模塊的設計中,解決了不同工作電壓晶元之間的介面問題,並給出了直接聯接的接線方案。
  3. And then, a method of load - flow low - pressure measurement was proposed in the light of the hydraulic - resistance theory of servo valve. the validity of the method was proved by the experimental results. therefore, the measurement of the characteristic of load - flow and no - load flow can be realized by using this method

    然後根據電液伺服閥的液橋理論提出了一種負載流量低壓測量方法,在所開發的測試系統上,利用電液比例閥模擬流量測量裝置對所提出的方法進行了試驗驗證,實現了利用低壓流量計和壓力傳感器進行電液伺服閥負載流量特性和空載流量特性的測量。
  4. Because this is an identification in a no - load full voltage starting mode, so there are some estimations which can bring some errors. so the following work should emphasis on how to get more exact parameters. and we can also expand this project not only identify the motor ' s parameters but also its other characteristic

    在本項目中,由於試驗條件所限,還是在一定程度內進行了近似計算,因此,在第五章的總結與展望中,作者提出本課題的兩個發展方向,一個是向更精確的方向發展,一個是在參數辨識的基礎上,進行電機其他特性的計算與檢驗。
分享友人