normal clearance 中文意思是什麼

normal clearance 解釋
正常間隙
  • normal : adj 1 正常的，平常的，普通的；平均的。2 正規的，標準的，額定的，規定的。3 智力正常的，精神健全的...
  • clearance : n 1 清除，掃除，除去；解除。2 【林業】終伐；（伐去樹木后的）林間空地。3 出[入]港證；放行證；出入...
  1. The hospital is answered to take out the injection overcoming a family name that fixed art uses after two half moon, classics x radiograph shows : fracture carries counterpoint good to the line, show an articulatory clearance is normal, scab having character grows

    兩個半月後回醫院取出固定術用的克氏針，經x光照片顯示：骨折端對位對線良好，指間關節間隙正常，有骨痂生長。
  2. Bearings, airframe rolling - rigid single row ball bearings in steel - diameter series 0 and 2. normal clearance category - dimensions and loads

    機體軸承.鋼制的剛性單列球軸承. 0號和2號直徑系列.標準游隙類.尺寸和負荷
  3. We will continue to effect improvements with the target of completing normal clearance procedures on both sides of the boundary within 30 minutes for passengers, and 60 minutes for goods vehicles

    我們會繼續改進工作，致力讓過境人士在半小時內貨車在一個小時內完成辦理兩地的過關手續。
  4. En 3284 aerospace series. bearings, airframe rolling. rigid single row ball bearings in steel. diameter series 0 and 2. normal clearance category. dimensions and loads

    航空航天系列.單排滾珠鋼制鋼性軸承.尺寸系列0和2 .標準間隙目錄.尺寸與負載
  5. Article 61 in accordance with the relevant regulations of the state, movement obstacle lights and marks shall be installed on high buildings or facilities, outside the civil airport and its obstacle clearance protection zone defined according to state regulations, that will possibly affect flight safety, and shall be kept in normal condition

    第六十一條在民用機場及其按照國家規定劃定的凈空保護區域以外，對可能影響飛行安全的高大建築物或者設施，應當按照國家有關規定設置飛行障礙燈和標志，並使其保持正常狀態。
  6. Secondly, based on cutting edge geometric model and machining mode of mk6335a grinder, the rake face with constant normal rake angle and flank face with constant orthogonal clearance angle models of ball - end cutters are discussed. the cutting geometry angle parameters are solved and analyzed. moreover, the tool paths models of wheel which grinding are builded and the post - processing technique for coordination transfer is studied

    然後，基於刃口曲線模型、五軸數控磨床刃磨運動方式和微分幾何的直紋面概念，本文推導與建立了具有等法前角的前刀面和具有等主后角的后刀面的球頭立銑刀數學模型，並對球頭立銑刀的刀具角度如刃傾角、主前角、法后角、主偏角等參數進行了求解與分析。
  7. Calculation of the normal side gear clearance of internal - engaging involute gear transmisson

    內嚙合漸開線直齒輪傳動法向齒側間隙計算
  8. Aerospaces series. bearings, airframe rolling. rigid single row ball bearings in steel, cadmium plated. diameter series 0 and 2. normal clearance category. dimensions and loads

    航空航天系列.飛機骨架滾動軸承.剛性單排鋼質鎘板球軸承.直徑系列0和2 .標準公隙.尺寸和負荷
  9. Bearings ; airframe rolling - rigid single row ball bearings in steel, cadmium plated - diameter series 0 and 2. normal clearance category - dimensions and loads

    機體軸承.鋼制的鍍鎘剛性單列球軸承. 0號和2號直徑系列.標準游隙類.尺寸和負荷
  10. Bearings, airframe rolling - rigid single row ball bearings in corrosion resisting steel - diameter series 0 and 2. normal clearance category - dimensions and loads

    機體軸承.耐蝕鋼的剛性單列球軸承. 0號和2號直徑系列.標準游隙類.尺寸和負荷
  11. Aerospace series ; bearings, airframe rolling - rigid single row ball bearings in steel - diameter series 0 and 2 ; normal clearance category ; dimensions and loads ; german version en 3284 : 1994

    航空航天系列.機體用軸承.鋼制單列自定心滾珠軸承.直
分享友人
分享到 Line

分享到臉書