normal mode of motion 中文意思是什麼
normal mode of motion
解釋
正常運動型-
Heat convected, a mode of motion developed by such combustion, was constantly and increasingly conveyed from the source of calorification to the liquid contained in the vessel, being radiated through the uneven unpolished dark surface of the metal iron, in part reflected, in part absorbed, in part transmitted, gradually raising the temperature of the water from normal to boiling point, a rise in temperature expressible as the result of an expenditure of 72 thermal units needed to raise i pound of water from 50 to 212 fahrenheit
燃燒所引起的運動形式之一-熱對流傳熱，不斷地加速度地從熱源體傳導給容器中的液體，由那凹凸不平未經打磨的黑色鑄鐵面把熱向周圍發散出去一部分反射回來，一部分被吸收，另一部分被傳導，使水的溫度從常溫逐漸升到沸點。這種溫度的上升可作為消費結果標志如下：將一磅水從華氏五十度加熱到二百十二度，需耗七十二熱量單位。 -
This drilling adopts crank connecting link and walking beam percussion mechanism, which make the drilling possess two percussive functions, normal drilling takes connecting link impact as main mode, when encountering special situation and the connecting link impact can not drill, it can transform into hoisting impact, the stroke length can be modulated, it realizes automatic percussive drilling due to continuous operating of connecting link percussive mechanism, these can enhance drilling efficiency and relieve labor intensity ; it adopts pumping reverse circulation to drain slag, which not only resolves the drilling difficulty in special stratum such as pebble and gravel stratum and hard stratum, but also resolves the problem that the percussive drill ' s efficiency is low ; it adopts spur gear differential mechanism as double cylinders lazy tongs of main hoist, which not only ensures the balance state of drilling tool, but also reduces the mechanical design, and reduces the cost ; the bottom plate traveling motion of this drilling machine adopts walking type ; the drilling tower adopts hydraulic pressure uprising, and reduces the assistant operating time
該鉆機採用曲柄連桿、游梁式沖擊機構，使鉆機具有兩種沖擊功能;正常鉆進以連桿沖擊為主，遇到特殊情況，用連桿沖擊不能鉆進時，可轉為卷揚沖擊，沖程可調，因連桿沖擊機構連續工作，所以實現了自動沖擊鉆進，可提高鉆進效率，減輕勞動強度;採用泵吸反循環的方式排渣，既能有效解決卵礫石地層、堅硬地層等特殊地層鉆進的困難，又很好地解決了沖擊鉆機效率低下的問題;採用直齒圓柱齒輪差速機構作為主卷揚的雙筒同步機構，既保證了鉆具處于平衡狀態，又大大簡化了該機構設計，降低了成本;該鉆機底盤行走移位採用步履式;鉆塔採用液壓起立，減少了輔助作業時間。 -
In this paper, to counter a flexible beam undergoing large overall motion impacting a fixed slope surface under the effects of grativity, the normal contact model is established based on the hertz theory and non - linear damping term, the tangential contact model is developed by adopting linear tangential contact stiffness to consider the effects of friction force during impact process, and the consistent linear dynamic model including impact is derived by using mode assumption method and lagrangin equation
針對在重力場下作大范圍回轉運動的柔性梁與一固定斜面發生斜碰撞的情況，根據hertz接觸理論和非線性阻尼項建立法向碰撞接觸模型。引入線性切線接觸剛度建立切向碰撞接觸模型，以考慮接觸過程中由於切向相對速度的換向作用引起的摩擦力的變化。利用假設模態法和lagrangian方程建立系統含碰撞過程的一致線性化的動力學模型。
分享友人