normal-pressure surface 中文意思是什麼
normal-pressure surface
解釋
正壓力面-
The sbf cultivation results by different surface modification methods were : nano - tio2 coating > alkali solution treatment > tio2 coatings sintered in normal pressure > tio2 coatings sintered in vacuum
不同表面改性方法的sbf培養結果比較為：納米二氧化鈦塗層堿液處理方法常壓下燒結二氧化鈦塗層真空下燒結制備的塗層。 -
Analyzing the propagation behaviors for open and close crack, the author gain that normal fault is more dangerous to earthquake than reverse fault and glide fault. 3. appling fracture mechanics to discuss reservoir - induce earthquake mechanism, the author observes the characteristic of surface crack and gains the stress intensity factor induced by the pressure of rock, water and osmosis
針對庫區斷層為表面裂紋這一特點，研究水庫地震的斷裂特點，得出地應力作用下的應力強度因子、庫水作用下的應力強度因子和滲壓作用下的應力強度因子以及它們的應力強度因子之合，並且合理的解釋了構造型水庫地震的誘發機理。 -
So the titanium dioxide coatings were fabricated by cladding substrates to sinter in different work mediums, which included normal pressure and vacuum conditions. the surface morphology and phase constitution of coatings were analyzed
本研究採用包埋燒結法分別在常壓和真空條件下在鈦合金試樣上制備二氧化鈦功能塗層，並對塗層的表面形貌和相組成進行了分析。 -
The paper proposes that the damage surface adopt curvilinear slip - surface, based on analyzing several normal models of soil pressure, and a new method of calculation soil pressure of brace structure of deep foundation - pit is derivated based on prandtl theory under this assumption. moreover contrasting against computational method of the classics soil pressure, better effect is acquired in the actual application
本文在對幾種常用的土壓力模型進行分析比較的基礎上，提出了採用曲線滑動面作為破壞面，並在此假設下根據普朗特爾理論推導出一種計算深基坑支護結構中土壓力的新方法，並與經典土壓力計算方法作了比較，在實際應用中也取得了較好的效果。 -
Based on the acoustic radiation mode analysis, the transfer matrix relating the pressure at every field point to normal component of surface velocity is formed
摘要基於聲輻射模態分析，建立了外部場壓和結構表面振動速度之間關系的傳遞矩陣。 -
The stability, rheology, chain structure and consecutive medium model in magnetorheological fluids are analyzed. according to the contribution of shear stress and normal pressure in polishing zone, the quantificational machining model of mrp is presented. as an example of plane workpiece, the influences of machining parameters on removal rate and surface roughness in mrp are studied
5 、磁流變拋光（ mrf ）是超光滑光學表面的一種新型加工技術，本文從mrf的磁、力學性質出發，研究了磁流液的穩定性、流變效應、鏈化結構和連續介質模型；根據拋光區內剪應力、正壓力的分佈特徵，提出了mrf的定量加工模型；然後以平面工件的磁流變拋光為例，揭示了工藝參數對材料去除率和表面粗糙度的影響規律。 -
It means implanting the skin tissue expander under the normal skin tissue and adding the capability of the expander in order to produce the pressure on the tissue of the skin surface to obtain the " additional " skin, which can be grafted for covering the wound
它是應用皮膚軟組織擴張器植入正常的皮膚軟組織下，通過增加擴張器內的容量，對皮膚表面軟組織產生壓力，使其擴張產生「額外」的皮膚軟組織，轉移覆蓋創面的一種方法。
分享友人