open die 中文意思是什麼

open die 解釋
敞開式鍛模
  • open : adj 1 開著的，開放的；可進入的，可分享的 （to）; 無蓋的，敞口的；敞開的；展開的；開的；開闊的，開...
  • die : vi （died; dying）1 死。2 滅亡，消滅；熄滅；枯死，凋落。3 漠然不受影響，感覺不到 （to） 。4 泄氣...
  1. Open die steel forgings for general engineering purposes - part 4 : stainless steels

    一般工程用開式模鍛鋼件.第4部分:不銹鋼
  2. Open die steel forgings for general engineering purposes - part 1 : general requirements

    一般工程用開式模鍛鋼件.第1部分:一般要求
  3. Open die steel forgings for general engineering purposes - part 2 : non - alloy quality and special steels

    一般工業用開式模鋼鍛件.第2部分:非合金優質鋼和特殊鋼
  4. The research and prediction of relative elongation of thick - walled tube without mandrel by open - die cold extrusion is the base of the design of tube parts and special equipment

    摘要對于無芯棒開式冷擠壓厚壁管件的相對伸長量的研究與預測是設計開式冷擠壓管類零件反其專用設備的依據。
  5. Various successive partial plastic forming methods for processing groove, including thread rolling, cross rolling and skew rolling, splitting, rolling of spline shaft, split rolling, open - die extrusion of spline shaft / gear, extrusion of internal screwed tooth socket parts with large helical pitch, integral cold forging for slot commutator, extrusion - ploughing for outside fin tube, drawing of tube with spiral internal / external ribs etc. have been introduced briefly

    摘要介紹了用於加工槽的各種連續局部塑性成形方法，包括螺紋軋制、橫軋與斜軋、分劈、花鍵軸滾軋、劈分軋制、花鍵軸齒輪開模擠壓、花鍵套擠壓、槽型換向器整體冷鍛、外翅片管擠壓一犁削、內外螺紋管拉拔等。
  6. The main parameters influencing relative elongate on are analysed by research on experiment of size prediction of thick - walled tube without mandrel by open - die cold extrusion, and their curves of changing rule are given, which applies reference in order to direct practical production

    本文通過對厚壁管件無芯棒開式冷擠壓尺寸預測的實驗研究，分析了影響相對伸長量的犯要參數，找出了它們與相對伸長量之間的變化規律曲線，為指導實際生產提供了依據。
  7. Open die steel forging for general engineering purposes - part 3 : alloy special steels

    一般工業用開式模鋼鍛件.第3部分:特殊合金鋼
  8. Steel forgings ; machining allowances and permissible variations for open - die forged bars

    鋼鍛件.第6部分:開式鍛模鍛造的棒材加工余量和允許變
  9. Machining allowance for open die forgings

    開式模鍛件的加工余量
  10. Steel forgings ; machining allowances and permissble variations for seamless open - die forged rings

    鋼鍛件.無縫開式模鍛環形件的加工余量和允許偏差
  11. Open - die forging

    開式模鍛
  12. Steel forgings ; machining allowances and permissible variations for open - die forged discs

    鋼鍛件.無縫開式模鍛盤形件的加工余量和允許偏差
  13. Steel forgings for pressure purposes - general requirements for open die forgings

    承壓用的鋼鍛件.敞口鑄模鍛件的一般要求
  14. Steel forgings for pressure purposes - part 1 : general requirements for open die forgings

    壓力用鋼鍛件.第1部分:開式模鍛件的一般要求
  15. Steel forgings for pressure purposes. part 1 : general requirements for open die forgings

    壓力容器用鋼鍛件.第1部分:開式模鍛件的一般要求
  16. Open die steel forgings for general engineering purposes - part 4 : stainless steels ; german version en 10250 - 4 : 1999

    通用工程用開式模鍛鋼件.第4部分:不銹鋼
  17. Open die steel forgings for general engineering purposes - part 1 : general requirements ; german version en 10250 - 1 : 1999

    普通工程用開式模鍛鋼件.第1部分:一般要求
  18. Steel forgings for pressure purposes - part 1 : general requirements for open die forgings includes amendment a1 : 2002 ; german version en 10222 - 1 : 1998 a1 : 2002

    壓力用鋼鍛件.第1部分:開式模鍛件的一般要求
  19. Theory research on the maximum reduction of deep tine taper hole formed by open - die cold extrusion

    深小錐孔擠壓成形極限變形程度理論判據建立
  20. Open die steel forgings for general engineering purposes - part 3 : alloy special steels ; german version en 10250 - 3 : 1999

    普通工程用開式模鍛鋼件.第3部分:特種合金鋼
分享友人
分享到 Line

分享到臉書