output-order control 中文意思是什麼

output-order control 解釋
輸出指令控制
  • output : n. 1. 產量；生產，出產，產品。2. 【醫學】（糞便以外的）排泄物；排泄量。3. 【電學】發電力，輸出功率；供給量。4. 輸出信號。
  • order : n 1 次序，順序；整齊；（社會）秩序，治安；狀況，常態；健康狀態；條理；會場秩序；議事程序，日程；...
  • control : n 1 支配，管理，管制，統制，控制；監督。2 抑制（力）；壓制，節制，拘束；【農業】防治。3 檢查；核...
  1. Apply computer chip to control the circuit ; omron opto - elecrtonic control - ler and panasonic and mitsubishi inverter have stable performance, high precision, rapid reaction and long life - span ; the controlling plate applies tactile operation board which is handled easily ; vertical structural screen is easy to adjust the vertical printing pressure so as to ensure the quality of printing ; the frame lift is driven by electrical motor and installed with imported linear guide rails, of which the speed - adjust device, scraper and scraping blade can be adjusted within15 to 45 and can be set for many times so as to repeatedly printing with good precision and output, the flat bed is made of 2mm stain - less steel plates which are flat, smooth and indeformable ; it is also equiped with micromatic setting device in order to ensure the precision of multi - color overprint and auto air - intake device to ensure strong adsorption

    採用電腦板控制電路，歐姆龍光電控制器，松下，三菱變頻器，行直穩定.精度高，反應快，壽命長，控制面板採用觸摸式操作面板，操作方便，六式結構型網版垂直升降印刷壓力可調保證印刷質量，機架升降採用電機驅動安裝進口直線導軌，刮刀、回墨刀可在15一45角調整，可設置多次，重復印刷保證產品精度.平臺板採用2毫米不銹鋼板製作，平整光滑不變形配有微調裝置，確保多色套印精度，配自動吸氣裝置，確保強有力的吸附。
  2. In order to eliminate the influence of the output filter capacitor current on the grid current, a novel control strategy for the grid - connected inverter in grid - tied and off - grid modes is proposed. the control strategy can also realize seamless transfer between grid - tied and off - gird modes. the grid - connected inverter can supply power to the critical load when the grid is off

    本文針對傳統並網控制策略進網電流受輸出濾波電容電流影響的問題，提出了一種新的並網控制策略，該控制策略能基本消除輸出濾波電容對進網電流的影響，實現獨立與並網兩模式之間的無縫切換，對關鍵負載起不間斷供電的作用。
  3. Step - nc ( iso14649 ) expends step into the area of cnc and renews the data interface between cax and cnc, which helps cnc system to use data models of products in three dimensions according with step directly in order to output nc programs then control machines directly, eliminate choke points of the information stream between cax, such as cad, capp, cam, cae, ped, erp and so on, connect the design product information and manufacturing product information on the base of step in the form of object - orientation, and change the traditional movement and switch control - orientation numerical programs into object - orientation programs

    Step - nc （ iso14649 ）將step擴展至cnc領域，重新規定了cax與cnc之間的介面，其目的是: cnc系統能夠直接使用符合step標準的cad三維產品數據模型，直接產生加工程序來控制機床;在step的基礎上以面向對象的形式將產品的設計信息與製造信息聯系起來，消除cax （如cad 、 capp 、 cam 、 cae 、 ped 、 erp等）與數控系統之間信息流瓶頸;將傳統的面向運動和開關控制的數控程序改變為直接面向加工對象的數控程序。
  4. The final results in the form of control pulses are output to servo system in order to drive the stepper motors, simulating the milling procedure of numerical control tool machine

    最終將處理結果以控制脈沖形式輸出給伺服系統，以控制步進電機的進給，達到模擬數控機床加工的目的。
  5. In order to reach the target of the curve of information input and value output extending along the optimized locus with the limited resources, this paper displays optimization of the model to control information input and value output

    通過對企業知識動力模型的優化，來控制知識的輸入與價值的輸出，從而達到在企業有限的資源條件下，使知識輸入?價值輸出曲線按最優的軌跡發展的目標。
  6. Furthermore, it is easy to use different control strategy in the digital inverter, so different pwm control can be used, in order to optimize the design of output filter and improve the output performance

    同時，在數字變換器平臺上可以方便地實現各種控制策略，達到進一步優化輸出濾波器參數、提高輸出電能質量、提高變速恆頻電源整體效率等目的。
  7. This thesis comes from the technological innovation project 2002 in xi ' an. the research is focused on the adaptive hybrid excitation synchronous generator system with constant output voltage. in order to keep the output voltage constant, the adaptive control is introduced in the digital voltage regulator of the generator system

    本課題來源於2002年西安市重大技術創新工程計劃?自適應復合勵磁恆壓同步發電機系統的研究，通過採用數字電壓調節器對復合勵磁同步發電機的自適應控制，實現發電機的恆壓發電輸出。
  8. A novel high - power pollution - free smps is presented in this paper, which accomplishes simultaneously the goal of soft - switching pwm, the input / output isolation, the output voltage regulation and three - phase pfc with a single - stage power processor and simple pseudo - phase - shift control circuit. therefore, compared with the normal two - stage system, the single - stage power supply has simpler structure, lower cost, higher efficiency and easier to control. the proposed smps can be used in the three - phase power system, and can output high power over kw - order and input / output ( i / o ) isolation dc power supply

    本文提出的新型無污染大功率開關電源正是採用三相三線制輸入電源，利用單級偽相移零電壓零電流開關脈寬調制（ pps - zvzcs - pwm ）全橋變換器完，成功率因數校正（ pfc ）和輸出電壓快速調節、隔離的雙重功能，並且該變換器開關管在零電壓或零電流下通斷，顯著的減小了emi 。
  9. . pcl - 711b card offers many functions such as a / d conversion, d / a conversion, digital input and output and so on. in order to saving time, lightening the diffculty of programming, i take the programming method of driver level to control pcl - 711b card using visual basic6. 0 language

    Pcl ? 711b卡提供了a d轉換、 d a轉換、數字量輸入和數字量輸出等i o功能，為了縮短開發時間，減輕開發的難度，本文採用了visualbasic6 . 0對pcl ? 711b卡進行驅動程序級編程來控制該卡。
  10. The pid control of output voltage feedback is easy to give attention to static and dynamic performance of the control system. output performance of inverter of ups is improved when rms of output voltage feedback is added to pid control system. the hardware and software is designed in order to achieve the digital pid control of inverter of ups

    設計了用於逆變器數字化控制的采樣調理電路，結合tms320f240的硬體資源，通過軟體實現了ups系統的緩起動和市電跟蹤，並改進了逆變器電壓瞬時值控制，通過引入輸出電流中心值檢測，對反饋電壓進行補償，解決了逆變器輸出的偏磁問題。
  11. The ic modulation circuits and microprocessor are used in the control unit. on the side of input of inverter, the maximum power point tracking of solar module is well realized by using a kind of thought of self - optimizing control ; on the side of output of the inverter, a kind of approximate optimum v / f control strategy is used in order to optimize the match between the output of the inverter and load of motor - pump

    在逆變器輸入側，採用自尋優控制思想實現太陽能電池最大功率點跟蹤（ mppt ） ；在輸出側，採用了v / f近似優化的控制策略，以優化逆變器輸出與機泵負載之間的匹配。
  12. This paper expatiated that the mathematics models of ac motor is higher order, non - linear and closed coupling, multivariable input - output system. and introduces the principle and the algorithm of sine pulse width modulation ( spwm ), opened - loop space voltage pulse width modulation control ( svpwm ) and field oriented control ( foc ). finally, realized the control strategies of variable - frequency speed regulating using assembly and c language

    文中闡述了交流異步電機的數學模型是高階、非線性、強耦合的多變量輸入輸出系統，介紹了交流電機的正弦脈寬調制、開環電壓空間矢量的u / f控制和磁場定向控制的原理及控制演算法，並利用dsp構成控制系統，通過匯編語言和16位定點c語言混合編程的方法實現了上述的變頻調速控制策略。
  13. Optimal predictive control to damp oscillation for linear time - delay systems with external sinusoidal disturbances is considered in chapter 4. a full - order state predictive observer for time - delay systems by using the control vector and the predictive output vector of the controlled plant is structured

    利用構造預測模型得到的被控對象預測輸出向量和系統的控制向量，設計一種全維狀態預測觀測器，並將該狀態觀測器用於時滯控制系統的最優前饋-反饋預測控制中。
  14. In this paper, the upper - class intelligent control scheme is adopted according to the characteristics of tobacco re - dryer and the present control condition in order to solve the problem that the output tobacco moisture can ? keep stable. that is, to keep the old every pid control link, to add the upper - class computer so that sets up the upper - class intelligent control system that consists of the description management sub - system, the fuzzy compensation on line sub - system and the self - learning system. the following are control procedure : first of all, a series of output values of description can be obtained by the forward inference of basic controller on the basis of the information of input tobacco, then, these output values can be adjusted by the fuzzy compensation controller with inquiring the fuzzy control - list on line in the light of the output tobacco moisture error

    本文針對烤機的工藝特點和目前控制現狀，提出用上位智能控制的方法解決烤機目前存在的問題，即在保留原有各段pid控制的基礎上，增加上位計算機，建立起由配方管理子系統、模糊在線修正子系統和自學習系統組成的上位計算機監控、決策的智能控制系統；控制過程為：基本配方控制器根據來料信息正向推理提供煙葉復烤機各段參數設定值的基值；模糊補償控制器根據煙葉水分偏差在線查詢模糊控製表提供相應參數設定值的修正值，實現煙葉復烤機參數的在線修正；學習環節的引入實現煙葉配方的在線優化。
  15. They are voltage to digit data converting circuit board, current to digit data converting circuit board and digit data input / output circuit board. these circuit boards are used to acquire the main running parameter of hev experimental bed and to control the output of alarm message. in order to simplify the wire connection and signal conditioning, three piece of interface circuit boards correspondence to the three data acquisition circuit boards are equipped, and a wire connection box is also designed to contain them

    本文監控系統的硬體以一臺工業控制pc機為核心並根據採集信號的性質配置了電壓-數字量轉換板、電流-數字量轉換板及數字量輸出輸出板，對hev運行系統的主要運行參數進行採集並進行報警控制；為方便接線和信號調理，配備了與採集板對應的接線和調理介面板以及接線盒。
  16. In order to obtain three - phase four - line ac output, system applied the four - legged main circuit topology. with the 3d - svm, the power system realizes voltage regulation and three - phase four - line output. meanwhile, this kind of control is easy to be realized in the digital inverter

    為實現三相四線的交流輸出，變換器電路採取四橋臂新型拓撲，其控制採取了三維空間矢量調制，實現了變換器的在線調壓及輸出中點的形成，具有良好的動靜態性能，且這種控制思想可以方便地在現有數字變換器平臺上實現。
  17. The control system of wind turbine includes individual control and group control. according to the control process and main technical parameter, the paper accomplishes the control system structure design and input - output system design. this paper also deeply analyzes the operation principle of the whole control system and the relation between each part in order to realize the no - person automatic operate

    本文以1mw變槳距風電機組為研究對象，根據其主要技術參數及控制工作過程，對其單機控制系統的構成進行了設計，闡述了輸入輸出介面和各個控制環節的運行原理及其相互之間的聯系與約束關系，從而實現在無人值守的條件下，實現多種預定的控制目標，並在此基礎上探討其更廣泛的適應性及實用性。
  18. Have synchronous control of input and output in order to avoid traction broken of cotton screen

    具有輸入、輸出的同步控制，避免棉網牽伸斷裂。
  19. Modeling analysis of state space for fractional - order multi - input multi - output control systems

    控制系統狀態空間建模分析
  20. Comparison research verifies its effectiveness on reducing the de - link losses and improving the output performance. the three topologies mentioned above are all presented with detailed theoretical analysis, parameters design, simulation and experimental verifications. a 6kw three - phase inverter system is accomplished in order to verify that the two - amplitude control technique is fit for high power application

    第五章研究三相逆變系統的雙幅諧振直流環節技術，完成了6kw實驗系統，提出了滯環電流控制與空間矢量調制相結合的方案（ hcc - svm ）並首次採用cpld實現邏輯控制，大大降低了逆變器換流頻率，縮短了控制延時，實現了逆變器的高效變換和低輸出失真。
分享友人
分享到 Line

分享到臉書