overlap mode 中文意思是什麼

overlap mode 解釋
交疊方式
  • overlap : vt vi （ pp ）1 （與…）交搭；疊蓋。2 （與…）部分一致[巧合]，（時間等）重復，一致 （in）。n 1 重復...
  • mode : n 1 法，樣，方法，方式。2 模，型；樣式，體裁，款式；習慣。3 風尚；〈the mode〉流行，時髦。4 【語...
  1. A complementary input stage, which consists of a p - channel pair and a n - channel pair, was used in the circuit, so that the common mode input range can extend from rail to rail. a dcls is used to shift the n - transistor curve leftward to overlap the p - transistor curve properly and keep constant transconductance in the whole common mode input range

    輸入級採用pmos差分輸入對和nmos輸入差分對並聯的結構，從而實現共模輸入范圍擴大到電源的正負兩端，並且通過兩個源級跟隨器平移nmos輸入管跨導曲線，使nmos輸入管和pmos輸入管跨導曲線的適當交疊，從而保持了這個輸入級的跨導在整個共模輸入范圍內保持恆定。
  2. The staring points of u exhibiting self - similarity and the symmetrical mode of the vortex street being destroyed almost overlap, both at x / h = 6. 0

    U達到自相似狀態的起始點與渦街的對稱性被破壞的起始點是幾乎重合的，即在x h = 6 . 0處。
  3. A novel cycloconverter - rype three - phase hf link inverter topology for soft - switching based on phase - shifted full - bridge mode is proposed, whose main advantages are as follows : under the conditions of d < i < and overlap - d, the switches of the leading leg are turned on at zvs and the switches of the lagging leg are turned off at zcs and all switches of the cycloconverter circuit are commutated in the overlapping mode in the interval of zero voltage, which makes the circuit realize soft switching to the utmost extent and reliably solve the problem of peak voltage caused by the storing energy of leakage inductance of hf transformer

    論文提出一種新型移相全橋軟開關周波變流型三相高頻鏈逆變器，電路的主要優點是：前級移相全橋的移相角控制在_ d _ i和_ （ overlap ） - _ d條件下，超前橋臂零電壓開通，滯后橋臂零電流關斷，並使周波變流器所有開關在零電壓期間重疊換相，使整機開關最大程度地實現了軟開關，並可靠解決了高頻變壓器漏感儲能引起的電壓尖峰問題。
  4. Analysis of nonlinear finite - element for ultimate strength of 81 overlap tubular k - joints with ansys program is carried out in this dissertation. the influence of nondimensional joints parameters, and ov on failure mode and ultimate strength of overlap tubular k - joints is studied. simultaneously, 27 tubular gap k - joints are analyzed for comparative purposes

    分析時考慮了四個無量綱參數，即支管直徑與主管的直徑之比；主管的直徑與壁厚之比；支管壁厚與主管壁厚之比以及支管搭接率o _ v對搭接節點破壞模式和極限承載力的影響。
  5. In this dissertation, the varied characteristics of soi rib waveguide were investigated, and the calculated results as well as simulated plots in theory were presented. it was the first time that a 3d overlap integral method was used to calculate the transition loss between the rib waveguides and the slab waveguides, in which the effect of the mode distribution in rib waveguides on the coupling efficiency was taken into account

    針對上述問題，本論文對soi波導的各種特性進行探討並給出了詳細的計算結果，首次用三維功率交迭積分法計算了soi波導器件中波導過渡區的損耗，這種方法考慮了脊形波導模式分佈對過渡區耦合效率的影響。
  6. For the coupling between the laser diode and the tapered single - mode fiber, the overlap integral is used to compute the coupling efficiency on the basis that the laser diode outputting mode field and the fiber eigenmode field is approximated to basic - mode gauss field. and based on the same approximation, the coupling efficiency between the semi - tapered fiber and the laser diode is calculated by using the ray - traced method. the parameters are analyzed for the effect on the coupling efficiency and give the theory foundation to optimize the design of the tapered fiber coupling system

    首先通過對半導體激光器輸出模式場和光纖本徵模式場的高斯基模近似，利用交疊積分計算了錐形單模光纖與激光器的耦合效率問題；其次依據以上近似，利用光線跡蹤法計算了半錐形多模光纖與激光器的耦合效率問題，給出各個參數對耦合效率的影響和作用，為優化設計錐形光纖耦合系統提供了理論依據。
  7. Muti - aperture overlap - scanning technique ( maost ) and target function can solve the problem of testing a large optical surface on the basis of ordinary digital interferometer of wavefront, and get the most information of wavefront in the end in the condition of big kr, muti - aperture overlap - scanning technique ( maost ) using target function is proved and we can get the most information of wavefront in the case of guarantee of high precision by the aid of simulation, experimental and tests, many influential factors, i. e., the apertureconnection mode, shape of mirror, error in subaperture test and kr are analysed contribute to controlling and testing large optical surface

    本文首先在較大孔徑放大系數（ 4 ）的情況下，論證了目標函數多孔徑拼接技術，保證了較高的精度，得到較完整的波前信息。然後，結合實驗結果，從拼接模式、被測面形、測量誤差、數字干涉儀解析度和不同孔徑放大系數等角度出發，分析了各種因素對精度的影響，並詳盡的探討了各種誤差源，包括靜態誤差、動態誤差、擬合誤差、拼接誤差。
分享友人
分享到 Line

分享到臉書