partial fracture 中文意思是什麼
partial fracture
解釋
部分骨折-
Amore 2001 has successfully investigated the gakkel ridge and arctic ocean in vicinity of its geological and geophysical nature, as well as the nature of sea ice and biology in this area. the preliminary onboard petrology and bathymetry results show that the mantle beneath the gakkel ridge with low temperature has only encountered very low degree partial melting during the spreading and there is no any direct relationship between the crust nature and the spreading rate along the gakkel ridge in any simple petrologic way. mantle temperature and fracture zone density also play a major role on the crust nature, besides spreading rate
對所取得資料的初步研究表明gakkel洋中脊之下的地幔僅經受了較低程度的部分熔融，具有較低的溫度。 gakkel洋中脊處的地殼性質和巖漿活動與擴張速率之間不存在任何直接的巖石學相關性，擴張而導致的巖石圈頂部的冷卻並不是決定洋脊處地殼性質的最重要因素。地幔溫度和斷裂帶的存在與否及其密度對地殼性質具有重要的影響意義。 -
Partial pulpotomy has been utilized in teeth with pulp exposure due to traumatic crown fracture
摘要局部斷髓常應用於因外傷牙冠斷裂導致牙髓暴露之牙齒治療。 -
Analysis results of histogram statistics and section electron microscopic scan technique, are that fracture feature of the cracks of the hbbb is similar and the crack is multi - source strain fatigue one. internal defects of the cast, such as impurities, gas holes, etc, are the main causes for early cracks. the contrast analysis of static strength, model and transient respond on three structures with fem proves that geometrical stress concentration in partial area has influence on early crack, also
利用直方圖等統計方法和電鏡掃描技術對該抱軸箱體裂紋分析的結果是：抱軸箱體的裂紋斷口特徵相近，裂紋性質屬于多源性低周疲勞裂紋，鑄件中的夾雜、氣孔等內部缺陷是導致過早裂損的主要原因；利用有限元法對該抱軸箱體三種結構的靜強度、模態和動態響應對比分析，證實了局部幾何性應力集中對過早裂損也有一定影響。 -
Analysis which was based on the fracture mode of mould in wire - cutting processing, and the results show that the partial - quenched of mould, the non - uniformity of blank temperature and the carbide segregation inside the material are the main reasons of deformation and cracking
摘要通過分析在線切割加工中模具的破壞形式表明：模具不完全淬火、坯料溫度的不均勻分佈、材料內部的碳化物偏析是模具變形與開裂的主要原因。 -
The results showed that the partial liquid phase was one of the main reasons for the premature fracture of the material during high temperature tension over 518
結果表明：局部液相是導致該復合材料在518以上高溫拉伸試樣過早斷裂的主要原因之一，為該材料超塑成形工藝參數的確定提供了參考依據。 -
Assume that material constants exponential functions or power functions of spatial variable, the related bending fracture models are set, i. e. a series of boundary value problems of partial differential equations are established
再將材料常數依次設為空間變量的指數函數和冪函數，建立了相應的彎曲斷裂模型，即一系列相關的偏微分方程的邊值問題。 -
The width of stacking fault increased as partial dislocations move forward. in the fracture of 18 - 8 stainless steel, many dislocations were emitted from the crack tip during the early stage of crack propagation and moved forward, and then a dfz was formed between the crack tip and the pile - up dislocations. the dfz is an elastic zone
不銹鋼斷裂時，裂尖首先發射位錯，並離開裂尖向前運動，裂尖前方留下無位錯區，位錯反塞積在無位錯區的端部，無位錯區是應變很高的異常彈性區，隨著裂紋的擴展，無位錯區逐漸發生晶體碎化和轉動。 -
In this thesis, it is analyzed theoretically the steel bar layout pattern, the prestress loss, the concrete stress, and the discipline of the deformation and the fracture forming of structures of the partial prestress concrete frame beams, which is widely used in modern civil engineering
本文從理論上分析了現代建築工程中廣為採用的部分預應力混凝土框架梁的布筋方式、預應力損失、混凝土應力、結構變形和開裂規律；導出了具有一般意義的預應力錨固損失以及梁的長期撓曲變形計算公式。 -
The microprocesses of deformation and fracture in 18 - 8 stainless steel were observed by in - situ tension in tem. it was found that the dislocations were emitted from the grainboundary and dislocation source inside a grain and slip along their slip system respectively. partial dislocation could also be emitted from the grainboundary, and moved into the grain, and that leaving behind a stacking fault
摘要浙江人學博1 ：學位論文採用透射電鏡動態拉伸、原位觀察icrlsnigti不銹鋼形變與斷裂過程，發現不銹鋼變形時，晶界和晶內位錯源均可產生位錯，並沿各自的滑移系運動。 -
Analysis study the fracture of cobalt - chromium alloy removable partial dentures
鉻合金鑄造可摘局部義齒折斷臨床分析
分享友人