path coefficients 中文意思是什麼

path coefficients 解釋
道路系數
  • path : path（ol ）＝pathological; pathology n （pl paths ）1 （自然踏成的）路；路徑；（馬路邊上的）人行...
  • coefficients : 系數
  1. Based on the theories of gear engagement, contact analysis, friction and heat transfer, a three - dimensional finite element model of gear tooth was established to investigate temperature distributions and variations along the contact path over a range of applied loads and operating speeds with consideration of lubrication conditions. sensitivity analysis of surface temperature to gear configuration, frictional heat flux, heat transfer coefficients, and oil and ambient temperature was conducted and the major parameters influencing surface temperature were evaluated

    本文基於齒輪嚙合原理、輪齒接觸分析、摩擦學和傳熱學，以有限元分析方法和理論分析計算相結合為手段並以實驗測量結果作為參考，建立了適用於工業應用並具有較高計算精度的高速齒輪傳動輪齒溫度分析的模型和方法，系統地分析了輪齒本體溫度的大小和分佈以及齒輪幾何、載荷及轉速和潤滑冷卻條件等對輪齒本體溫度的影響。
  2. The effects of sowing dates on phenotype value of grain weight per plant, seed setting rate and path coefficients of seed setting rate were more effective than those on partial correlation coefficients between grain weight per plant and panicles per plaht, total spikelets per panicle and seed setting rate

    播期對單株產量、結實率及結實率相對重要性影響較大，而對單株產量與單株有效穗、穗粒數及結實率的偏相關影響較小。
  3. Nc machining requires " interpolation " algorithms that accurately and efficiently generate sequences of reference position, distributed according to a prescribed feedrate function, along the tool paths. this paper present a systematic derivation of the proper taylor series coefficients for variable feedrate interpolators. when the path is ph curves, detailed formulations for instances are presented where the feedrate v is specified as a constant, the function of the time t, the arc length s and the local curvature k

    對于nc加工要求插值演算法沿著刀具路徑準確、有效的生成參考點序列（根據預先指定的速率函數進行分佈）的實際工程需要，本文系統地推導了變速率插值運算元的泰勒系數，給出了當路徑為ph曲線，速率v為常數，及時間t 、弧長s 、曲率k的函數時具體的插值運算元。
  4. In addition, several way are adopted to optimize the one dimensional transform architecture. improving the architecture resulting from the standard lifting scheme reduces the critical path delay ; an embedded boundary extension algorithm is adopted instead of the standard symmetric extension and it ’ s easier to implement ; the pipeline technique is adopted to increase the speed of processing ; coefficients of the multipliers are transformed into csd forms and the multiplications are substitute by minimum shift - add operations

    改進了由標準的提升演算法得到的變換結構，減小了關鍵路徑上的延時;採用內嵌的邊界延拓來代替標準的對稱延拓，實現更加簡單;採用流水線技術顯著提高了處理的速度;把乘法器系數表示為csd形式，將常系數乘法優化為最少的移位加操作。
  5. Later the characteristics of sea - surface reflected ( including specular and diffuse ) coefficients are investigated as well as the origin of multi - path effects

    再研究了海面反射（包括鏡面反射與漫反射）系數的特性，影響多徑效應的因素等。
  6. Finally, on the base of further analyzing path coefficients, the research showed that the most important influence factor to turnover intention was balanced organization responsibility and job satisfaction, secondly, relational organization responsibility and organization satisfactory sense, in the end, emotion promises and transactional organization responsibility

    第四，在對路徑系數進一步分析的基礎上，發現離職傾向最大的影響因素是平衡型組織責任和工作滿意度。其次，影響離職傾向比較大的因素是關系型組織責任和組織滿意感，最後是情感承諾和交易型組織責任。
分享友人
分享到 Line

分享到臉書