pinion 中文意思是什麼

音標 ['pinjən]
pinion 解釋
n. 名詞 1. （鳥翼的）翼梢；翅膀；羽毛；〈集合詞〉翮；〈詩〉翼。
2. （人的）臂膀；臂綁。
vt. 及物動詞 1. 剪斷…的翮毛，捆住…的兩翼。
2. 捆住（兩手）；箝制，束縛。
n. 名詞 【機械工程】小齒輪。
a lazy pinion 惰輪。

  1. The gearing machine tool of the model y3150e is modified and a new milling head is designed to cut the envelope tooth of the pinion using allelomorph method. a assembled drawing of clamp for cutting the tooth shape of circle - arc gear is also presented

    對y3150e型滾齒機進行改造，設計出一新型的銑削頭，利用對偶法加工小齒輪的圓弧包絡線齒形；同時也給出了加工大齒輪圓弧齒形的夾具裝配圖。
  2. Finally, the paper studied the dynamic characteristics of 2. 6x13m mill system. mill system of single - pinion drives is lighten, so the design and run of mill system, bestir frequency must avoid inhesion

    邊緣傳動磨機系統是一個模態偶合較緊的系統，因此，在磨機系統的設計、運行中，應注意使激勵頻率避開系統的固有頻率，以免發生設備的早期失效。
  3. The four main types of gears (spur, helical, worm, and bevel)and a rack and pinion are shown in figure 7.

    圖7所示是四種主要的齒輪（巨齒輪，斜齒輪，蝸輪和傘齒輪）以及齒條和小齒輪。
  4. Usually, we adopt pinion drive for large mills

    大型磨機我們通常採用邊緣驅動。
  5. Pinion - type cutters for cylindrical gears ; tolerances

    圓柱齒輪用插齒刀.公差
  6. Bevel pinion shaft carrier

    小錐齒輪軸架
  7. Bevel pinion shaft

    圓錐齒輪軸
  8. Tabular layouts of article characteristics for racks, cylindrical gears, pinion shafts, bevelgears, bevel pinion shafts, worms and worm wheels

    齒條圓柱齒輪小齒輪軸傘齒輪圓錐齒輪軸蝸
  9. The trunnion sprocket has come off the pinion, but don ' t worry - we ' ll soon but that right

    耳軸鏈齒脫離齒輪，不過不要緊? ?我們馬上可以修好。
  10. Specification for pinion type cutters for spur gears - 1 to 8 metric module

    正齒輪插齒刀規范. 1至8米制模數
  11. Pinion - type cutters for cylindrical gears ; disc - gear cutters for spur gears

    圓柱齒輪用插齒刀.直齒輪用盤形齒輪銑刀
  12. Pinion - type cutters for cylindrical gears ; shank - gear cutters for spur gears

    圓柱齒輪用插齒刀.直齒輪用帶柄齒輪刀具
  13. Tabular layouts of properties - part 143 : pinion type cutters with bore or shank

    事物特性表.第143部分:帶孔和柄的插齒刀
  14. Pinion - type cutters for cylindrical gears ; design, dimensions, definitions, marking

    圓柱齒輪用插齒刀.設計尺寸定義標志
  15. Pinion - type cutters for cylindrical gears ; extended hub gear cutters for spur gears

    圓柱齒輪用插齒刀.直齒輪用加大轂形齒輪刀具
  16. Geometrical design of cylindrical internal involute gear pairs ; diagrams for limits of internal gear - pinion type cutter matings

    漸開線嚙合圓柱內齒輪副的幾何設計.內小齒輪刀具配合
  17. Small animals such as bushy tailed rats, chipmunks and pinion mice are being chased upslope by rising temperatures, until they at last have no place to run

    而一些小型的動物，如花栗鼠，因為溫度不斷的升高而必須往高處遷徙，直到沒有地方可走。
  18. Drive pinion gear depth

    驅動齒輪深度
  19. Axle drive bevel pinion

    車軸傳動的小傘齒輪
  20. Check the gear wheel drive in the groove of the wall, select four gear wheel ( red pinion is not used ) of different size for use, load heavy gear wheel, times of heavy gear wheel, times of light gear wheel, minimum gear wheel most onto separately from left to right, make gear wheel hand in, form each other, leave behind, operate a switch, drive, finish

    檢查墻壁凹槽中的齒輪驅動裝置，選用大小不同的四個齒輪（紅色的小齒輪不用） ，從左到右分別裝上最大的齒輪、次大的齒輪、次小的齒輪、最小的齒輪，並使齒輪間相互交結，拉下拉閘，驅動完成。
分享友人
分享到 Line

分享到臉書