polyethylene filler 中文意思是什麼

polyethylene filler 解釋
聚乙烯填充物
  • polyethylene : n. 【化學】聚乙烯。
  • filler : n. 1. 裝填者，斟酒人；注入器，漏斗；填充物。2. （雜志的）補白；電影補白短片。3. 雪茄煙心；（自來水筆的）吸墨管。4. 〈pl. 〉【化學】填料。5. （計算機的）進位填充數，填充位。
  1. Tga. insulating and sheathing materials of electric and optical cables - common test methods - part 4 - 1 : methods specific to polyethylene and polypropylene compounds - resistance to environmental stress cracking - measurement of the melt flow index - carbon black and or mineral filler content measurement in polyethylene by direct combustion - measurement of carbon black content by termogravimetric analysis - assessment of carbon black dispersion in polyethylene using a microscope

    電纜和光纜的絕緣和護套材料.通用試驗方法.第4 - 1部分:聚乙烯和聚丙烯化合物專用方法.抗環境應力致裂.熔化流動指數測量.通過直接燃燒測量聚乙烯中炭黑和或礦物填料含量.通過熱重分析法
  2. Insulating and sheathing materials of electric and optical cables - common test methods - part 4 - 1 : methods specific to polyethylene and polypropylene compounds - resistance to environmental stress cracking - measurement of the melt flow index - carbon black and or mineral filler content measurement in polyethylene by direct combustion - measurement of carbon black content by thermogravimetric analysis - assessment of carbon black dispersion in polyethylene using a microscope

    電纜絕緣護套材料的通用試驗方法.第4部分:聚乙烯和聚丙烯專用方法.第1節:耐環境應力破裂性.在空氣中熱老化后的卷繞試驗.熔體流動指數測量.聚乙烯中炭黑和
  3. Common test methods for insulating and sheathing materials of electric cables. part 4 : methods specific to polyethylene and polypropylene compounds. section one : resistance to environmental stress cracking - wrapping test after thermal ageing in air - measurement of the melt flow index - carbon black and or mineral filler content measurement in pe

    電纜絕緣和護套材料通用試驗方法第4部分:聚乙烯和聚丙烯混合料專用試驗方法第1節:耐環境應力開裂試驗-空氣熱老化后的卷繞試驗-熔體指數測量方法-聚乙烯中碳黑和或礦物質填料含量的測量方法
  4. Common test methods for insulating and sheathing materials of electric cables - part 4 : methods specific to polyethylene and polypropylene compounds - section 1 : resistance to environmental stress cracking - wrapping test after thermal ageing in air - measurement of melt flow index - carbon black and or mineral filler content measurement in pe

    電纜絕緣和鎧裝材料通用試驗方法.第4部分:聚乙烯和聚丙烯復合物專用方法.第1節:耐環境應力裂化試驗.空氣中熱老化后的纏繞試驗.溶體流動指數的測量. pe中炭黑和或礦物填充料的含量測量
  5. In attempt to prepare and study the novel electrically conductive nanocomposites, with polyethylene ( pe ) served as the matrix, maleic anhydride grafted polyethylene ( gpe ) served as eg intercalates and expanded graphite ( eg ) served as a conductive filler, prepared gpe / eg, pe / gpe / eg electrically conductive composites via solution intercalation ( si ), direct melt mixing ( dmm ) and master batch melt mixing ( mmm ) methods. by means of testing conductivity and mechanical property, with the measures of tem, sem, om, xrd and dsc, studied the relationship between preparation method, material composition, and electrically conductive as well as mechanical property. the main outcomes never reported at home and abroad literature were obtained as follows : 1 the gpe / eg electrically conductive nanocomposites were prepared via si method

    本論文以制備和研究新型高分子導電納米復合材料為目的，以聚乙烯（ pe ）為基體，馬來酸酐接枝聚乙烯（ gpe ）為插層劑，膨脹石墨（ eg ）為導電填料，採用溶液插層（ si ）法、直接熔體混合（ dmm ）法和兩者相結合的熔體母料混合（ mmm ）法制備了gpe eg 、 pe gpe eg導電復合材料，通過電導率和力學性能測試，運用tem 、 sem 、 om 、 xrd和dsc等手段，研究了制備方法、材料組成、形態結構和導電性能及力學性能之間的關系，得到以下未見國內外文獻報道的研究結果： 1採用si法成功制備了gpe eg導電納米復合材料，其導電逾滲閥值（ _ c ）為1 . 59vol ，遠低於dmm法制得gpe eg常規復合材料的_ c （ 3 . 13vol ） 。
分享友人
分享到 Line

分享到臉書