position sleeve 中文意思是什麼

position sleeve 解釋
定位套
  • position : n 1 位置；方位；地點。2 處境，情況；狀態，形勢，局面。3 姿態，姿勢。4 地位，身份；職位；職務。5 ...
  • sleeve : n. 1. 袖子，袖套。2. 【機械工程】套筒，套管，套。3. 唱片套。4. 【氣象學】風（向）袋。vt. 給…裝袖子，給…裝套筒。adj. -less
  1. Stem : the tee - head disc - stem connection prevents lateral strain on the stem for smooth, easy operation. accurately cut threads engage the yoke sleeve for positive control of disc position

    閥桿： t形閥瓣-閥桿連接防止施加在閥桿側面的應力，確保操作平穩順暢容易。軛架套管準確的螺紋連接有助於閥瓣位置的調整控制。
  2. The valve stem with its grooved rings and positioning sleeve indicates the throttled position of the valve

    閥桿及其溝槽環和定位套筒顯示閥門的節流位置。
  3. Position the fuser film sleeve into heater, and the end of the film with ground ring should be in good contact with the conductive rubber gear of pressure roller or the conductive brush after installation

    請在安裝新定影膜前，在塑料架與定影膜接觸的部位均勻塗上硅脂，盡量在有棱的地方多塗點，以保證定影膜與塑料架的充分潤滑。
  4. Temperature field of hollow ingot solidification is simulated by fem. to different mould, effect of heat transfer coefficient between inner sleeve and cooling medium and thickness of core refractory on final position of solidification, the highest temperature of inner sleeve against cooling medium, and shrinkage cavity and porosity are compared. in addition, change of temperature in typical position of core refractory is also compared

    對空心鋼錠凝固過程的溫度場進行了有限元分析，對不同錠型結構的芯部換熱系數、耐火材料厚度對最終凝固位置、內筒壁最高溫度及縮孔疏鬆的影響進行了對比，並討論了耐火材料典型部位的溫度隨凝固時間的變化。
  5. Abstract : temperature field of hollow ingot solidification is simulated by fem. to different mould, effect of heat transfer coefficient between inner sleeve and cooling medium and thickness of core refractory on final position of solidification, the highest temperature of inner sleeve against cooling medium, and shrinkage cavity and porosity are compared. in addition, change of temperature in typical position of core refractory is also compared

    文摘:對空心鋼錠凝固過程的溫度場進行了有限元分析，對不同錠型結構的芯部換熱系數、耐火材料厚度對最終凝固位置、內筒壁最高溫度及縮孔疏鬆的影響進行了對比，並討論了耐火材料典型部位的溫度隨凝固時間的變化。
  6. The distribution of the gas - flow speed is measured at a position 1cm away from the outlet ( the end with larger air - gap ). it is illustrated that the gas - flow speed keeps increasing from the out surface of the inner sleeve to the inner surface of the outer sleeve, and then it decreases gradually

    測量了楔形氣隙流體出口（大間隙埠）外1厘米處空氣流速大小的分佈，發現空氣流速自轉子（內筒）壁面處開始逐步增大，至定子（外筒）壁面處達到最大值，隨后開始減小。
  7. A sketch must be easy to understand, and clearly indicate the position of seams, pockets, darts, type of collars, width of sleeve, etc

    圖紙必需簡潔明了，要清楚地標注出拼接和縫和的位置，以及袋位，領型袖寬等參數。
  8. B : a sketch must be easy to understand, and clearly indicate the position of seams, pockets, darts, type of collars, width of sleeve, etc

    圖紙必需簡潔明了，要清楚地標注出拼接和縫和的位置，以及袋位，領型袖寬等參數。
  9. Note : the valve is shipped in the closed position. the indicator on the plastic sleeve is aligned with the vertical scribed line on the stem

    注意：閥門裝運時是處于關閉位置。塑料套筒上的指示器與閥桿上的垂直刻線對齊。
分享友人
分享到 Line

分享到臉書