power-on-signal 中文意思是什麼
power-on-signal
解釋
電流接通信號-
Due to existing signal processing technology ’ s shortage such aslow measurement, narrow measurement range precision and other poor performance, we introduced a high - precise signal processing technology : firstly, to get power spectrum with hanning windowed welch modified periodogram, search its peak value frequency ; secondly, to apply zooming analysis via goertzel algorithm ; at last, to get a highly precise doppler frequency with energy centrobaric rectifying algorithm 。 the simulating result indicated that this technology introduced could get accurate doppler frequency 。 depending on above discussed technology, we designed a signal processing scheme, and developed a signal processing system. the running result showed high performance, verified the feasibility and reliability of the highly precise signal processing technology introduced. in a word, the technology improved ldv ’ s performance such as measurement precision, measurement range, dynamic response time 。 and it will have a wide application foreground
針對存在的缺點，本文提出了一種應用於激光多普勒測速的高精度信號處理技術，即首先利用加hanning窗的welch修正周期圖演算法得到信號功率譜，搜索其譜峰值頻率，接著利用goertzel頻譜細化演算法對搜索的譜峰進行細化分析，再引入能量重心頻譜校正演算法對細化后的譜峰進行校正分析，從而將離散頻譜分析演算法、頻譜細化演算法和頻譜校正演算法三者有機結合起來，充分發揮各自的優點:通過加hanning窗的welch修正周期圖演算法快速得到功率譜及峰值頻率，通過goertzel演算法獲得分析頻帶的高解析度頻譜，然後通過能量重心校正演算法對細化后的頻譜進行高精度校正，這樣不僅保證了演算法的高效性，而且大大提高了分析的精度。 -
The thesis presents a expert system for identifies power quality disturbance signal, after compare the artificial neural network, nearest neighbors, fuzzy decision, and expert system. we bring forward the project flexible rule - based expert system, according to the characteristic inspection and measure system, and has a deep research on the problem of this system. this project for disturbance classifies has lower mistake ratio and facility maintenance
採用專家系統的方法進行模式識別，在對神經網路、最近鄰法、模糊邏輯和專家系統及一些交叉方法等模式識別方法進行比較分析的基礎上，根據電能質量信號故障分析的特點，提出了採用規則基專家系統的方法，該模式識別方法具有便於擴展、修改和識別率高等特點。 -
Based on an analysis of uhf ( ultra - high - frequency ) characteristic of pd ( partial discharge ) in power transformer, using mixing technique, a signal disposal cell has been devised for the sake of facilitating common data sampling card
摘要在分析了電力變壓器局部放電的超高頻特性的基礎上，利用混頻技術，設計了局部放電超高頻信號的信號調理單元，方便普通數字採集卡採集。 -
Expounds the five main aspect of risk in national commercial bank, i. e. signal liability structure, bad loan quality, low capital efficiency, imperfect restriction on interior power, thin consciousness on risk avoidance ; summarizes five characters of the bank risks, including risk concentration, moral risk, risks caused by system structure, inequi ty between bank risks and revenues, aggrandizement trend of bank risks ; analysis eight reasons for bank risks, including proprietary ownership voidance, macroeconomic fluctuation, ineffective capita ] buffer mechanism, enterprise reasons. no synchronous fiscal investment and financial reform, incompetence law and regulation enforcement. chapter4 argues the opportunities and challenges of the financial globalization and requirement for bank risk managem ent. chapters suggests the methods for the risk management of national commercial bank
緊接著在第三章闡述了我國國有商業銀行風險的「五大表現」 ，即負債結構單一、信貸資產質量差、資本充足率低、內部控制機制薄弱、防範風險的意識淡薄；總結了我國國有商業銀行風險的「五大特點」 ，即風險高度集中、風險人為匿藏、風險的體制性、風險與收益嚴重不對稱、風險呈繼續擴大態勢；剖析了我國國有商業銀行風險形成的「八大因素」 ，即金融產權「人格」虛設、宏觀經濟波動、資本金等緩沖機制不健全、財政、投資和金融的體制改革不配套、法律和法規不健全等。 -
Based on an amplified spontaneous emission ( ase ) source, a ring - cavity fiber laser, in which sensor element acted as the reflector of the cavity, was achieved with high - signal noise ratio ( snr ) and high - power. it was demonstrated that the output power was maximum, when output coupler ratio of the coupler was seventy percent
實驗證實耦合器的輸出耦合比選為某一個最佳值70 ，當980nm泵光工作電流為50ma時，其輸出功率達3 . 5mw ，且輸出激光波長與作為反射鏡的光纖光柵中心波長相同。 -
When blanket jamming is used, the more the ratio between the power of jamming and the power of signal, the less detection probability of the radar is. the effect of distributed jamming mainly depends on the total power. after distributed, the randomicity of distance and phase of jamming source bring difficulties to analysis
對壓制式干擾來講，干信比越大，雷達的發現目標的概率就越小，由於分散式干擾的干擾效能在於其合成功率，在分散式干擾單元分佈之後，各個干擾源與被干擾對象之間的距離的不確定性，帶來了干擾信號相位的不確定性，增加了分析干擾效能的復雜度。 -
Secondly, the paper researches blind estimation of signals parameters, including the carrier frequency, signal to noise ratio and symbol rate of digital modulations. thirdly, with the combination of parameters from early studies on the decision theory, a set of robust feature parameters are extracted from signal power spectrum and the power spectrum of the second and fourth power of signal. based on these parameters, the proposed scheme is able to recognize 12 types of common used modulations, namely ask 、 2fsk 、 msk 、 4fsk 、 psk 、 qpsk 、 / 4qpsk 、 8psk 、 am 、 dsb 、 ssb 、 fm
接著，對信號功率譜、平方譜及四次方譜進行研究，針對通信中常用的調制方式，結合前人提出的基於決策理論中的特徵參數，設計了一組對信噪比和信號調制參數不敏感的分類特徵參數，利用上述參數完成了一種基於信號頻域的識別方法，可以對ask 、 2fsk 、 msk 、 4fsk 、 psk 、 qpsk 、 / 4qpsk 、 8psk 、 am 、 dsb 、 ssb和fm這12種常用調制方式進行識別。 -
By applying dwt and mallat in wavelet analysis, the oscillation signal of active power on transmission line is decomposed and reconstructed ; the strategy of upfc ' s secondary control based on wavelet is proposed by using the reconstructed active power as input signal. simulation results verify the efficiency of damping subsequent swing quickly under serious power oscillation circumstance that is hard to damp by ordinary upfc controller. the system dynamic stability is apparently enhanced
針對系統功率波動頻率較高情況下upfc對系統后續擺穩定的控製作用難以得到充分發揮的情況，採用小波分析的mallat塔式演算法對系統功率波動信號進行分解，並基於mallat塔式重構演算法的思想濾除了信號的冗餘擾動成份，尋找到一個高壓縮比、低相對誤差的重構功率信號，從而使其能夠符合upfc實際控制需要。 -
To accelerate the development of next generation high dwdm system, the pape r also researches the property of gain. based on optical wave nonlinear transmission equation, the gain model of fra is established. by the way of numerical analysis, it is obtained that the gain of fra has relation with pump power, input signal wave power, the effective area and absorption of fiber. the obtained conclusion has definite instruction to the design of fra
為了促進下一代超高速dwdm密集波分復用技術的發展，本文還研究了光纖喇曼放大器的增益特性，根據光波非線性傳輸方程建立光纖喇曼放大器增益模型，通過數值模擬分析了泵浦波功率、信號輸入光功率、以及光纖有效面積和損耗對光纖喇曼放大器增益的影響，得出了一些對光纖喇曼放大器的設計有一定的指導意義的結論。 -
Current voltage isolated conversion module is a kind of miniaturization insert type construction conversion module, between its supply power input signal and output signal are isolated each other, its input ac voltage or ac current can be transformed into ma or v standard signal output. it has accuracy high, linearity good, debug simple, work stable and reliable and so on features, apply to electricity parameter display, record and monitor of the dcs system fields
電流電壓隔離轉換模塊是一種小型化插裝式結構的轉換模塊，其具有工作電源輸入信號輸出信號三者相互隔離，能將輸入的交流電壓或交流電流轉換成420 ma或15 v標準信號輸出，具有精度高，線性好，調試簡單工作穩定可靠等特點，適用於電量參數的顯示記錄dcs系統的監控等場合。 -
Guide to methods of measurement of short duration transients on low voltage power and signal lines
低壓電源和信號線路的短時間瞬態測量方法指南 -
Guide on methods of measurement of short duration transients on low voltage power and signal lines
在低電壓和單線上短期持續瞬態的測量指南 -
The purpose of the subject is to design a monitoring system which is small, reliable, low price and complete function for railway signal power, the signal system ' s heart. the system is suitable to the unwatched power room of the locality, while the work such as collecting, communication, alarm and so on is accomplished by the way of long - range control
本課題研究的目的是為鐵路信號系統設備的心臟?鐵路信號電源設計一個體積小、安全可靠、價格低、功能完備的監控系統，使之適用在當地無人執守的電源室里，而一切諸如採集、通訊、報警等工作都可以通過遠程監控的方式來實現。 -
Is a kind of miniaturization insert type construction conversion module, between its supply power input signal and output signal are isolated each other, its input ac voltage or ac current can be transformed into ma or v standard signal output. it has accuracy high, linearity good, debug simple, work stable and reliable and so on features, apply to electricity parameter display, record and monitor of the dcs system fields
是一種小型化插裝式結構的轉換模塊，其具有工作電源輸入信號輸出信號三者相互隔離，能將輸入的交流電壓或交流電流轉換成420 ma或15 v標準信號輸出，具有精度高，線性好，調試簡單工作穩定可靠等特點，適用於電量參數的顯示記錄dcs系統的監控等場合。 -
While in this mode a signal is input to the subwoofer, the subwoofer automatically turns on ( auto power on / off function )
在此模式時，如果有信號輸入到副低音揚聲器，副低音揚聲器便可自動地打開電源（自動電源開關功能） 。 -
On the designed system, make experiments on calculating the harmonics of rectangular wave and power supply signal. the correctness of design is proved by experiments
在研製的系統上，進行了計算輸入信號為方波和動力電源信號時的諧波大小的實驗，實驗結果表明了研製成果的正確性。 -
This thesis designs automobile braking performance inspecting and control system. this thesis consists of three main parts. something about automobile braking system design has been discussed in the first part according to the main requirement of gb7258 - 2004 《 the requirement for motor vehicle, running safely 》. the hardware has been designed according to the characteristic of the parameter afer establish the whole plan for inspecting it. and then working principle of each part has been introduced. and at last, we designed software depending on the require to inspection and function. we can educe the braking power of both wheels, braking moment retardarce power and other parameters. we designed sensor signal processing circuit which including power sensor signal processing circuit and speed signal measure circuit according to the require of designing parameter. ad620 is used as power sensor. in order to measure the power of the automobile braking and protect the electromotor. so we must measure both
由汽車制動測試原理以及制動性參量檢測的技術指標可知，檢測數據準確性、控制可靠性、實時性和抗干擾能力是系統設計的關鍵。本文在掌握汽車性能檢測系統結構和原理的基礎上，根據國家有關標準和汽車制動性檢測系統的控制邏輯提出了採用單片機為控制器的總體方案，設計了各部分硬體電路，並根據所要實現的功能用c51語言設計了軟體。由於檢測現場存在各種干擾噪聲，為了保證系統運行的穩定性和可靠性以及測量精度的要求，分別從硬體和軟體的角度出發，介紹了常用的硬體抗干擾措施以及軟體數字濾波的原理和方法。 -
At using the meters, customers can get signal samples through enlargement, multiplication, integral, v / f exchange and divided frequent power on the divided current and divided voltage meters to drive stepping motors and counters add up energy degrees
用戶使用電表時，對分流分壓器上進行信號取樣，經放大、乘法、積分、 v / f變換、分頻、功率驅動等電路的處理，驅動步進馬達帶動計度器累計電能度數。 -
Secure communications method for higher power information signal based on chaotic masking is proposed
摘要提出了一種適合較大功率信息信號的混沌掩蓋通信方法。 -
The paper analyses the signal processing with emphasis on signal to noise ratio ( snr ) in output of correlator and snr in signal power spectral density
並對演算法處理中相關器輸出中的信噪比（ snr ）和功率譜密度中的snr進行了重點分析。
分享友人