protective concrete layer 中文意思是什麼

protective concrete layer 解釋
保護混凝土層
  • protective : adj. 1. 保護的，防護的。2. 保護貿易的。adv. -ly ,-ness n.
  • concrete : adj 1 具體的，有形的；實在的，實際的。2 固結成的，混凝土製的。3 圖案詩歌的（參閱concrete poetry）...
  • layer : n 1 放置者，鋪設者，計劃者。2 【賽馬】（一般）賭客。3 產卵的雞。4 【軍事】瞄準手。5 層；階層；地...
  1. Fabrication of the box beam is divided into such parts as reinforcement, formwork, concreting, prestressing, moving and storing of beam, pipe grouting under pressure, end sealing of the beam, water - proof layer on the bridge surface system, protective coating etc. the paper makes description of effective box beam construction technology and workmanship which can be adopted in other projects, such technologies as : manufacturing and fixing of reinforcement, steel reinforcement fixing baseplate, web plate and top plate respectively and lifting the steel skeleton into form, requirements of design and manufacturing and way of utilization for dismantling - erection type formwork and hydraulic formwork, optimization of concrete ratio, concrete pouring process of two ends of beam in priority over the middle, in sequence of first baseplate followed by web plate and top plate at last, concrete pouring in inclined section and in horizontal layer, concrete vibration mainly by external vibrator in assistance with internal vibrator, methods and regulation for steam curing of concrete, dual controls over stress and strain to ensure quality of prestressing workmanship, construction method of effective beam moving by heavy - weight special moving facility, some regulations and key notes about construction of grouting under pressure, beam ends sealing, water - proof layer on the bridge surface system, protective coating

    箱梁製造由鋼筋工程、模板工程、混凝土工程、預應力工程、移存梁工程、孔道壓漿工程、梁體封端工程、橋面防水層和保護層工程等施工環節組成。文中介紹的採用胎具製作和綁扎鋼筋，分底腹板和頂板分別綁扎並吊裝鋼筋骨架入模；拆裝式和液壓式兩種模板的設計、製作要求和使用方法；綜合考慮、優化混凝土配合比，混凝土灌注從兩端至中間、先底板、后腹板、再頂板的施工順序和斜向分段、腹板水平分層、附著式振搗為主、插入式搗固為輔的施工工藝，蒸汽養護的方法和規定；應力應變雙控制確保預應力施工質量的施工技術；採用重物移運器有效移梁的施工方法；壓漿、封端、橋面防水層和保護層施工的一些規定和注意事項等都是對箱梁製造行之有效的施工技術和施工方法，並可為以後類似施工作借鑒。
  2. Reasons : firstly, sectional dimension is so little that torsional stiffness of single - beam is n ' t enough. secondly, protective layer thickness is too thin to protect concrete reinforced bar and reduce durability. lastly, each main beam is joined by cross girder and the more rigid of cross girder the more entirety of bridge

    橋梁局部損壞較嚴重，主要原因是主梁截面尺寸過小、肋板過于薄弱，造成單梁抗扭剛度不足；保護層厚度不夠導致鋼筋外露引起銹蝕，降低了橋梁的耐久性；各主梁採用橫隔梁連接成整體，橫隔梁的剛度越大，橋梁的整體性越好，但調查結果顯示，實際情況中並不能達到理想的整體剛度。
  3. Protective layer of concrete

    對混凝土保護層的認識
  4. The calculation results show that the value of crack width obtained from the new and old hydraulic design specification is different, especially, the member with thicker concrete protective layer, and that the value obtained from industrical and civil building design specification is larger than that from hydraulic design specification, so its design result is safe than hydraulic design

    實例表明新、舊規范的裂縫寬度值計算差異較大，特別是混凝土保護層厚度較大時，同時工民建規范計算公式的計算值較水工規范計算公式的值大，故偏於安全。
  5. Analysis of protective layer thickness for bar in concrete as well as the control

    混凝土結構鋼筋保護層厚度的分析與控制
分享友人
分享到 Line

分享到臉書