pull-out resistance 中文意思是什麼
pull-out resistance
解釋
拔拉阻力- pull : vt 1 拉,拖,牽,曳 (opp push); 勒(馬)。2 拽住;扯破,扯開。3 拔去(雞等的)毛;拔(牙齒、瓶...
- out : adv 1 〈位置及運動的方向〉向外,向外部;在外,在外部;出去,出外,離開;離岸,向海面;(船等)開...
- resistance : n. 1. 抵抗,反抗,抗拒,抵禦;敵對,抵抗力,反抗力,阻力,【生物學】抗病性。2. 【電學】電阻;阻抗;電阻器。
-
At last, according to the comparison and analysis of the model fea results, model experiment data and the { specifications for design of highway reinforced earth engineering } ( jtj015 - 91 ) that is put into practice at present, we suggest that the polymer - geogrid reinforced earth walls in this area, which earthquake intensity is greater than 7 degreefincluding 7 degree ), must be analysed and designed with the earthquake fatalness, must be carried on with the checking computations of the reinforced material ' s intension and stabilization safety factor of the resistance against pull out
最後,根據有限元計算結果和試驗數據對比現行的《公路加筋土工程設計規范》 ( jtj015 - 91 ) ,建議地震烈度在7度以上(包括7度)的地區應對加筋土擋墻結構採取地震危險性分析設計,應對加筋土擋墻進行筋材抗震強度和筋材抗拔穩定安全系數的驗算。 -
Roofing. fasteners. determination of the characteristic resistance of the assembly. test method to determine the pull - out load of fixings out of insulating material or sealing coating from the frame
屋面.緊固件.組件抗性的測定.測定嵌固件從框架絕緣材料或密封塗層拉拔力載荷的試驗方法 -
Based on the pull - out tests data between geogrids and expansive soil / sands arranged by the orthogonal table l9 ( 34 ), the following conclusions are reached : 1 ) the displacement - properties of pullout tests depend on the pullout speed. the law of factors " affecting degree, which influences the parameters between geogrids and soils in the pulling - out procedure, is obtained. with the concept of " equivalent pull - out displacement ( x ) " brought forward, the whole process of pull out tests is divided into two process - " main process ( when x 1. 0 ) " and " residual process ( when x 1. 0 ) ", and three stages - static friction resistance stage, slip friction resistance stage, and residual friction resistance stage
基於正交設計表l9 ( 3 ~ 4 )分別安排了影響因素與土工格柵膨脹土或砂土界面相互作用參數的拉拔試驗數據,獲悉: 1 )拉拔試驗位移特性主要取決于影響因素中拉拔速率;通過分析並獲取影響因素對筋土界面相互作用參數的影響程度及其在拉拔試驗過程中的變化規律,提出了當量拉拔位移( x )的概念,並據此將拉拔試驗全過程劃分成「主過程( x 1 . 0 ) 」和「殘余過程( x 1 . 0 ) 」 ;且將影響因素對拉拔力或摩擦阻力系數的影響程度分成三階段(靜摩擦阻力階段、滑動摩擦阻力階段,殘余摩擦阻力階段) ; 2 )不同(規范)定義的筋土界面摩擦阻力系數數值相差較大,但影響因素對摩擦阻力系數影響程度及其變化規律不會因不同(規范)定義而受到影響。 -
Roofing - determination of the characteristic resistance of the assembly - test method to determine the pull - out load of fixings out of insulating material or sealing coating from the frame
屋頂.耐安裝特性的測定.框架絕緣材料或封裝塗層外的部件拉出力測定的試驗方法 -
Roofing and wall cladding - determination of the characteristic resistance of the assembly - test method to determine pull - out load of fasteners in crown or valley fixing out of their subconstruction
屋頂和墻面覆蓋層.耐安裝特性的測定.固定在拱頂或屋谷下層結構之外的緊固件的拉出力測定的試驗方法 -
Roofing and wall cladding - determination of the characteristic resistance of the assembly - test method to determine the pull - out load of the plates assembly from the subconstruction for plates made from steel or aluminium
屋頂和墻面覆蓋層.耐安裝特性的測定.鋼制或鋁制板材用的板材組件從下層結構中抽出的負載測定的試驗方法 -
Roofing and wall cladding. fasteners. determination of the characteristic resistance of the assembly. test method to determine the pull - out load of the plates assembly from the subconstruction for plates made from steel or aluminium
屋面和墻壁覆面.緊固件.組件抗性的測定.測定部件結構平板組件拉拔載荷的試驗方法用於鋼或鋁制平板 -
Thermoplastics piping systems - end - load bearing mechanical joints between pressure pipes and fittings - test method for resistance to pull - out under constant longitudinal force
熱塑管道系統.壓力管和配件之間端部承載的機械接合.在恆定徑向力下抗拔出性能的試驗方法
分享友人