pulse controller 中文意思是什麼

pulse controller 解釋
脈沖控制器
  • pulse : n 1 脈搏；有節奏的跳動；【動物；動物學】脈沖（波）；脈動。2 意向；傾向。3 【音樂】拍子，律動。vi ...
  • controller : n 1 管理人，主管人。2 （會計的）主計人，檢查員；〈英國〉（特指宮廷、海軍等的）出納官〈常作 comptr...
  1. In the positioning servo - system, which generally is configured by the d. c. pulse width modulator ( pwm ) velocity governing system and position servo - loop, the parameter perturbance of pwm velocity loop really exist by reason of such as the load behavior ; power voltage supply ; operating setting value, etc. 1, 2 ， and it cannot be ignored. by using the identification technique to form the mathematical model of the system, authors have confirmed the facts. therefore, to design the discrete sliding mode controller ( dsmc ) of the positioning servo - system, the perturbed parameters value bounds of the pwm velocity loop, which is as the controlled plant of position servo - loop, should be accounted. consequently, the design principle of dsmc for accounting system with parameter perturbance is proposed by the authors. the proposed method can ensure the stability of system with parameter perturbance and the behavior of non - overshoot, fast precise positioning. in order to reveal the effects of the design method, the comparative research work is done by the authors. also, it has been tested in an industrial experiment, the results proved it is satisfactory

    由直流脈寬調速系統（ pwm ）和位置環構成的定位系統中，速度環的參數隨負載特性；電網電壓；給定工況而攝動是不容忽視的.作者通過系統辨識建模也證實了這一事實1 ， 2 .因此在設計位置環的離散滑模控制時，必須針對速度環（即位置環的控制對象）的參數攝動范圍採用「對象參數攝動離散滑模控制器的設計方法」 ，以確保系統在參數攝動時的穩定性和快速、無超調、準確定位的優良動態品質.為剖析該設計方法的控制效果，本文作了對比性研究，並將該設計方法用於工業試驗中，取得了滿意的結果
  2. 2 、 metal halide lights start more difficult than other types of high - intensity gas discharge lights. the work circuit of the metal halide lights and the lc series resonance start controller are analyzed, and its shortcomings are noted. through the relations of breakdown voltage ? time, the thesis discusses a quick - start controller using pulse transformer

    2 .金屬鹵化物燈的啟動問題較其它類型的高強度氣體放電燈更為困難，作者對金屬鹵化物燈的工作電路進行了理論分析，對目前常用的lc串聯諧振啟動方式進行了較為詳細的理論研究，並指出了其存在的缺點。
  3. Development of the digital dc - speed controller of the pulse load

    脈動型負載的數字式直流調速器
  4. To realize nolinear excitation controller, it must be improved that the disposal speed of nolinear excitation control " s signal. with analyzing and comparing all kinds of microcomputer excitation controller, a new microcomputer excitation control scheme is offered that is based on dsp controller while the cpld chip is utilized for realizing the function of pulse trigger. it is described in detail that the method of realizing controllable silicon digital logic by verilog hardware describe language and the designed digital pulse trigger " s veracity was validated by digital simulation

    論文進一步針對非線性勵磁控制要求信號處理速度高、信息量大的特點，在對目前微機勵磁控制器分析基礎上，提出採用dsp控制器晶元作為核心處理器的微機勵磁控制器的解決方案，運用復雜可編程邏輯器件cpld晶元實現可控硅同步脈沖觸發單元，並簡要說明了verilog硬體描述語言和數字脈沖形成邏輯的方法，通過電路數字模擬對所設計的數字觸發單元進行了驗證。
  5. According to step - response experiment, math model of the hotplate was set up and the temperature of controlling system including temperature detection circuit, pd controller, voltage pulse - wide transforming circuit and executor was designed

    以階躍響應實驗為基礎，初步建立起控制系統的數學模型，設計了適用於該電熱板的閉環溫度控制系統。系統主要包括溫度檢測電路、 pd控制器、電壓-脈寬變換電路及執行元件。
  6. Our item choiced msp430f149, a sort of singlechip as controller, designed our hardware electrocircuit to get the pulse wave singnal, and used msp430f149 to continuously search and calculate the peak - peak value of the pulse wave, and compute oxygen saturaction. in our study, in order to hurdle the dirft of baseline caused by the physiological difference of human bodies. we designed one circuit which can automatically regulate of the baseline of signal

    本文以msp430f149晶元為控制器，設計硬體電路提取脈搏波信號，連續檢測脈搏波峰?峰值，計算氧飽合度。本課題採用了基線自動調節電路，以克服不同人體生理差異引起的基線漂移；設計了直流截取電路和可控積分放大電路，以滿足臨床連續監測的特殊需要，解決信號飽和問題。
  7. A pulse vacuum sterilization controller based on at89c55 is designed according to the requirements and the work characteristics of the medical treatment

    摘要根據醫療行業對高溫滅菌的使用要求和工作特點，研製了基於at89c55單片機的脈動真空滅菌器。
  8. Step power is the key for step magnetic potential, the pulse width modulate technology that selects the triangle wave as the carrier and ladder sine wave as the modulate wave is researched, furthermore the design of the actuator drive adopts dsp as the digital controller is introduced

    步進電源是產生步進磁勢的關鍵，文章研究了三角波為載波，階梯正弦波為調制波的脈寬調制技術，進而介紹了採用dsp組成全數字控制器，完成步進電源觸發的執行器驅動器的設計。
  9. With the conduction property of the triggered thyristor and the intellective numerical controlled frequency reduction of the triggering pulse by mpu, we can divide alternating current into several complete sinusoidal waves to supply some loads. it can be made as a controller or a pcb ware, which is suitable for the air conditioning, machine tool and various instruments that require electric power or rotate speed adjustment

    利用晶閘管的觸發導通特性，用單片機對觸發信號進行智能數字降頻，可在交流電中切分出部分完整的正弦波形供負載使用，可以單獨做成一臺控制儀器或者作為一個控制電路板用於需要電功率和轉速調節的空調、機床以及各類儀器設備中。
  10. The range - finding and aiming device is an important component of the self - propelled gun fire - control system, which is consisted of pulse liquid lazer, an automatic mounting unit with step by step motor, and a master controller box specified for information control and management, etc. modern warfare requires a low rate of weapon malfunction and consequent stoppage

    自行火炮測瞄裝置是自行火炮火控系統的重要組成部分，它由脈沖固體激光器帶步進電機的自動裝表機構和一個以信息處理和控制為中心的主控箱等組成。現代戰爭要求武器裝備要有一個盡量小的故障發生率和故障停機率，一旦發生故障，要求維修人員能迅速準確地判斷故障單元和故障性質。
  11. In order to get data, the plane use the way of comparative between the black line and white line. the device is composed of the pulse producer, system controller, signal processor, logic analyzer, interface circuit and electrical machinery driver. this device could follow the tracks of the plane graphic border automatically

    跟蹤裝置運用黑白交界圖線比較法取得數據，由步進脈沖發生器，系統控制器，信號處理器，邏輯判別器，介面電路，電機驅動器等組成，可對平面圖形邊界進行自動跟蹤控制。
  12. Firstly, the basic theory of switch reluctance generator ( srg ) is discussed in detailed, based on the mechanism electric energy converting analysis, non - linear analysis and non - linear simulation. three control methods of srg ( angle position control method, current chopping control method, pulse width modulation control method ) are deeply studied and analyzed. the electronic controller, which controlled by dsp or by hardware circuit are developed for low - power switched reluctance generation system

    首先系統地研究了開關磁阻電機發電運行的基本理論，從機電能量變換的角度分析開關磁阻發電機的機電能量變化規律；通過非線性分析和非線性模擬方法，明晰開關磁阻電機發電本質，概括出開關磁阻電機發電運行的特點；系統、深入地研究了開關磁阻電機發電運行的控制方案（角度位置控制、電流斬波控制、脈寬調制控制） 。
  13. The paper analyses its key circuit and software program structure. this full - digital controller is made up of dsp and implements single neuron adaptive pid computation, current pi computation, logical determination, pulse - fire and procession of protective signal etc. it also improves the reliability and availability of this control system

    本課題對控制器主要的電路結構及程序結構進行了分析，以dsp為核心組成的全數字式控制器完成了電流pi演算法計算，單神經元自適應pid演算法計算、邏輯判斷、脈沖觸發以及系統保護信號的處理等，提高了控制器的可靠性和可操作性。
  14. Input pulse signal can be directly transformed into micro - step linear motion by use of linear pulse motor, which have found wide applications in the digital linear servo systems with high positional accuracy and high reliability. taking slpmu - 025a, a two - phase hybrid lpm manufacturing by shinko motor company ltd, as an specimen, the study on the drive control system is carried out in this thesis, which contains : ( l ) three kinds of drive circuits are designed and comparison analysis in theory is done ; ( 2 ) introduction to at89c51 microchip as controller and special micro - step constant current driver, a great variety of running modes driver control are developed ; ( 3 ) experimental testing and theoretical analysis of current waveforms and displacement graphs and velocity graphs are carried out in case of different micro - step constant current driver

    本文以日本神鋼電機株式會社生產的兩相混合式直線脈沖電機slpmu - 025a為樣機，對直線脈沖電機的驅動控制系統進行了研究，內容包括： （ 1 ）設計了幾種直線脈沖電機驅動器電路，從理論上進行了對比分析研究； （ 2 ）用at89c51單片機作為控制器，採用專用的恆流細分驅動器sh ? 2h057m ，實現了開環控制方式下對slpmu ? 025a樣機各種運行方式的驅動控制； （ 3 ）對不同細分數下恆流驅動的電流波形以及各種運行方式下的位移圖、速度圖進行了實驗測試和理論分析研究。
  15. The proposed control system includes the attitude controller acting on the rigid hub, designed by using pulse - width pulse - frequency ( pwpf ) modulation integrated with command shaping technique based on csvs method, and the piezoelectric material elements as sensors / actuators bonded on the surface of the beam appendages, designed by the optimal positive position feedback ( oppf ) control technique, in which the selection of ppf gains is determined via introducing a cost function to be minimized by feedback gains which are subject to the stability criterion at the

    設計的控制器僅利用輸出信息，從而避免設計撓性模態狀態觀測器以及引入狀態觀測器誤差;在此基礎上，採用分力合成方法設計命令成形控制器來抑制撓性附件的振動，設計的優化命令成形控制信號在理論上可以對系統的各階撓性模態完全抑制。但考慮到模型不確定性和外部擾動，在內迴路又設計了最優正位置反饋（ oppf ）補償器以增加撓性結構的阻尼，使撓性結構的振動能夠很快衰減。
  16. A development and updating solution for the controlling system of a high - power special pulse power supply as used in the process of potting in magnesium and aluminium ect light - alloy surface is discussed. the power supply controller adopts intel 16 bit signal chip employing the core of controller, full - bridge controlled rectifying and reversing technique in its main circuit, pulse width modulation technique is adopted in controlling circuit

    控制器採用intel16位單片機80c196kc為核心，電源主電路採用全控整流技術和逆變技術，控制電路採用pwm （脈寬調制）控制方式，電源實現了雙向不對稱脈沖輸出和在大電流、高電壓工況下主要技術參數的大范圍連續可調。
  17. In this thesis, assembler language was applied to program to realize dsp algorithm controller, which can perform such main computing as data collecting, self - adaptable distortion current detecting based on linear nerve cell, capacity voltage controlling in the side of direct current based on fuzzy control, pwm pulse width computing based on unsymmetrical rule sampling, etc. quick control speed ( one work period is 50 s ) and high accurateness feature largely in the controller

    本文採用匯編語言編程實現了dsp演算法控制器，它完成了數據採集、基於線性神經元的自適應畸變電流檢測、基於模糊控制的直流側電容電壓控制、基於非對稱規則采樣的pwm脈寬計算等主要演算法的運算。該控制器具有控制速度快（一個工作周期為50 ） ，精度高等特點。
  18. According to the principle of lower cost, higher reliability, the design completes much work. the contents of project are as follows : ( 1 ) pic micro - controller which is lower - power and lower price is the core of control device. the whole circuit realizes the functions of collecting pulse, keeping data, driving electric machinery valve, reading and writing ic, detecting power supply, sound alarm and liquid crystal display

    設計依據低成本，高可靠性的原則完成了以下工作： （ 1 ）用功耗低、價格便宜的pic系列單片機作為控制裝置的核心，控制裝置的硬體電路實現了脈沖採集、數據存儲、電機閥驅動控制、 ic卡讀寫、電源檢測以及聲音報警和icd液晶顯示等功能。
  19. The specetrum data - collecting subsystem is controlled by a single - chip micro - controller at89c52, including 1024 - channel pulse - height analyzer and rs232c serial communication interface

    譜數據採集子系統由單片微控制器at89c52控制，包括1024道脈沖幅度分析器和rs232c串列通訊介面。
  20. The controller takes full advantage of the features of ti tms3201f240xa processor, such as high performance processing capabilities, plenty of peripherals on chip and high real time control. by the vital of these features the fast ac sampling, synchronic pulse, digital shift phase trigger pulse, can bus communication, pid control method and excitation limitations are realized. the pretreatment of the switch signals and the test of the shift phase trigger pulses are realized by using the complex programmable device ( cpld )

    該勵磁控制器充分發揮了tms3201f240xadsp處理器的強大的數據運算能力、豐富的片內外設資源和較強實時控制能力，用單片系統結構實現了快速交流采樣，數字同步脈沖形成， can現場總線網路、以及pid控制演算法和各種勵磁限制等功能；用cpld器件實現了開關量抖動預處理和可控硅觸發脈沖遺漏的檢測，減輕了dsp處理器負擔，提高了勵磁控制器可靠性、抗干擾能力和控制能力；使用vc + + 6 . 0開發的基於windows操作系統的勵磁系統調試軟體，人機界面簡潔友好，使用操作靈活方便。
分享友人
分享到 Line

分享到臉書