pulse signal source 中文意思是什麼
pulse signal source
解釋
脈沖信號源-
Advantages, disadvantages and limits of arm are thoroughly examined using signal processing methods. based on the above, incoherent and coherent two - point - source decoy methods and modified coherent two - point - source decoy methods to deflect arm are brought forward. arm ’ s homing heads are generally of mono - pulse structure, so coherent two - point - source ’ s interference resembles that to mono - pulse radar except that interference to radar belongs to far field scope, but interference to arm varies from far field to near field because relative distance drastically changes between the homing head and the two - point - source with missile ’ s homing head continually approaching the target
Arm的導引頭一般為單脈沖體制，因此，相干兩點源對導引頭的干擾類同於對單脈沖雷達的干擾，不同的是:對雷達的干擾都是遠場，而導引頭隨著導彈不斷接近目標，兩點源與導引頭的相對位置發生劇烈變化，由遠場變化到近場;導引頭天線口面上的合成場也發生了大的變化，相位波前的畸變產生干擾，這就是相干兩點源誘偏的基本思想。 -
The hardware circuit design include : industrial control computer configuration, selection of industrial control board type, design of the power supply and monitoring interface circuit, design of signal processing interface circuit ( the constant current source circuit, the time base signal processing circuit, the processing circuit for the signal to be measured ), design of panel control circuit, design of the system self - checking circuit, and etc. the program flow hart include : main program flow chart, system boot - strap self - checking program flow chart, manual static testing program flow chart, semiautomatic static testing program flow chart, automatic static testing program flow chart, dynamic testing program flow chart, transient testing program flow chart, source voltage and current monitor program flow chart, investigate function testing program flow chart, and etc. the measure system offers six working power supplies, the signal of time base, the signal of constant current source, sine wave signal and step to leap signal, and measures the frequency of the output pulse signal of the wide range pulse convert circuit accurately under three kinds of different test state ( static form, dynamic form and transient form )
硬體電路設計包括：工控機配置、工控板卡選型、產品電源及監控介面電路設計、信號處理介面電路（恆流源電路、時基信號處理電路、被測信號處理電路）設計、面板控制電路設計、系統自檢電路設計等。程序流程圖包括：主程序流程圖、系統開機自檢程序流程圖、手動靜態測試程序流程圖、半自動靜態測試程序流程圖、自動靜態測試程序流程圖、動態測試程序流程圖、暫態測試程序流程圖、電源電壓和電流監控程序流程圖、研究功能測試程序流程圖等。測試系統提供六路工作電源、時基信號、恆流源信號、正弦波信號和階躍信號，並對三種不同測試狀態（靜態、動態、暫態）下大量程脈沖變換電路輸出脈沖信號的頻率進行精確測量。 -
In this system, cpld controls semiconductor laser, the fet controls surface light source by the way of changing input voltage to control current, and the pulse signal of 1khz produced by at89c2051mcu controls yag laser
系統中使用cpld控制半導體激光器，使用場效應管通過改變輸入電壓控制電流的方法來控制面光源，通過at89c2051單片機產生1khz的脈沖信號來控制yag激光器。 -
According to the carrier wave leakage and mirror wave interference in the signal generation, this paper analyzes the source of waveform distortion and its influence to signal spectrum and pulse compression result
針對生成信號中存在的載漏和鏡像等失真，本文對波形失真來源及其對信號頻譜及脈壓結果的影響進行了全面分析與模擬。 -
Summarizing the development statement of monitoring technology for bridge, based on principle of pulse laser ranger detection and fiber - optic strain measurement, in view of the problem affected by single - chip inherent feature, integrating the goodness of cpld device and single - chip, using a / d converter to measure the count quantization error, a strain measurement system is worked out. the above system chiefly consists of light source, optic fiber sensor, photo detector and signal processing circuit
本文綜述了國內外橋梁監測技術的發展概況，在深入研究脈沖激光測距和光纖應變測試原理的基礎上，針對單片機固有計數頻率低、計數量化誤差大和延時不固定等不足，結合cpld計數頻率高、延時小而固定和單片機控制功能強的優勢，並採用模數轉換技術設計計數量化誤差測量電路，提出了基於激光脈沖時間測量法的光纖應變測量的方案。 -
The mixed control chip sg3525a combined with hardware pi controller generates the high - frequency pwm pulse for the first inverter. the digital control block tms320lf2407a mainly provides current preset for constant - current source through the outer filter, pwm pulse for the second inverter and drive signal for the high - frequency pulse power supply
其中變極性電源的一次逆變pwm信號由pwm發生晶元sg3525a ，配以外部硬體電路pi調節器產生;一次逆變閉環控制迴路的電流給定（配以外部濾波） 、二次逆變pwm驅動以及高頻脈沖電源的控制則由tms320lf2407a數字控制器實現。 -
A system for the weld power source was established with digital signal processor ( dsp ), and variable polarity power supply output, high - frequency pulse current, protection and process control were fulfilled with the software all, and modulate low frequency pulse current by means of amplitude modulation, through which it could also control the shape of weld seam like the low frequency pulse current welding
在模擬控制器基礎上引入了dsp數字控制技術，用軟體編程實現了電源的變極性輸出、高頻脈沖電流的疊加及保護和電源的時序控制，使之能夠在大尺度上調制出低頻脈沖，控制焊縫成形。
分享友人