pulse-power output 中文意思是什麼
pulse-power output
解釋
脈沖功率輸出-
Second, the results of theory analysis and simulation research show that the output of one cycle controlled bridge switching power amplifier have dc offset because of the nonideal characteristic of reset signal. the magnitude of output dc offset voltage is proportional to width of reset pulse. a voltage compensation technique is used to solve this question, and the computation formula of compensation voltage is gived. the circuit compensated and not are researched through simulation and experiment, which results show that compensated circuit solve the output dc offset effectively
其次，理論分析和模擬研究結果表明，由於復位脈沖的非理想特性，單周控制的全橋開關功率放大器輸出端存在直流偏置問題，其大小與復位脈沖的寬度成正比。針對輸出直流偏置問題，提出了電壓補償的改進方案，給出了補償電壓的具體計算公式。對補償前和補償后的方案進行了對比模擬研究和實驗研究。 -
We apply the agrawal ' s theory model of soa, and study the temporal characteristics of the output pulse for input picosecond optical pulses with different sharpness edges passing through a semiconductor optical amplifier, and find that the peak power and the pulse width of the output pulse depend on the input pulse peak power, the sharpness degree of the input pulse edge and the bias current of soa
本文應用agrawal的關于soa理論模型，詳細研究了具有不同陡峭邊沿的皮秒超高斯光脈沖經soa后的時域特性的變化，發現輸出脈沖的峰值功率、脈沖寬度與輸入脈沖的峰值功率、輸入脈沖邊沿的陡峭程度以及soa的偏置電流密切相關。 -
Traditional laser iff has poor security because of low frequency of laser beam coded pulse. this can be greatly improved when the pulses are modulated by continuous wave laser, but the power of this laser beam output is so low that it ’ s difficult to be detected and received by laser warning subsystem
傳統的激光敵我識別器激光編碼脈沖頻率低，通信保密性差，使用連續波激光器經調制后激光編碼脈沖頻率高，保密性好，但輸出激光功率較低，難以達到激光告警分機探測接收的要求。 -
Combining high voltage new technology and power electronics technology, this paper developed a controllable steep pulse generator ( cspg ) that can control the energy of output pulse accurately. applied with this generator, a lot of cell experiments and animal experiments were carried out. based on these works, it ' s easier to research mechanism of irreversible electrical breakdown ( ireb ) of malignant tumor cell under steep pulse, and it may be helpful to generalize energy controllable steep pulse therapy ( ecspt ) on cancer treatment
為了研究能量可控陡脈沖對惡性腫瘤細胞不可逆性電擊穿的機理，並將能量可控陡脈沖療法應用於惡性腫瘤的臨床治療，本論文研製出了一套能對輸出陡脈沖的能量進行精確控制的陡脈沖發生裝置，並應用該裝置進行了大量的醫學細胞實驗和動物實驗。 -
The main circuit is consisted of 18 thyristors circuit and protection circuit. with the help of control subsystem, it can get the output of low frequency voltage ( current ) with the shape of sine wave ; the core of the control subsystem is the cpu of 87c196kc, and the synchronization circuit, the pulse - widen circuit, and the power - enlarged circuit form the accessorial subsystem of the control system. it possesses all the functions of digital triggering, digital tuning, analog / digital conversion ; the input transfer can isolate the input and output ; and the circumfluence reactor can reduce the circumfluence
主迴路採用由18個晶閘管組成的三相零式電路，並輔以晶閘管的保護電路，通過控制可以得到低頻正弦波的電壓（電流）輸出；控制迴路主要以87c196kccpu為核心，其外圍電路包括同步電路，脈沖拓寬電路，功率放大驅動電路等，完成了數字觸發、數字調節、模數轉換等功能；進線電源變壓器具有變壓和隔離作用；環流電抗器則實現了有效抑制主迴路瞬時脈動環流的功能。 -
The nonuseful loss of cavity were got by measuring the threshold of laser under the different output mirrors. the loss was caused by prague angle unmatching. 3. the pulse train with minor pulse width 22ns and frequency 23khz, peak power 3. 5kw were obtained in cr4 " : yag passively q - switch experience. the stability of pulse is 6 %
（ 3 ）實現了在大功率泵浦、無水冷的情況下cr ~ （ 4 + ） : yag飽和吸收體被動調q ，得到了最小脈寬為22ns 、重復頻率為23khz 、峰值功率為3 . 5kw的激光脈沖輸出，脈沖的穩定性為6 。 -
Power balance is necessary to icf, including the energy balance and pulse shape uniformity at the target. 90 percent of the output energy of " sg - ii " comes from its double - pass coaxial array main amplifiers, and pulse shape distortion caused by gain saturation also occurs mostly in there. therefore precise control of gain performance of the main amplifiers by avm ( angular variable mirror ) is the key to the precise power balance of " shenguang - ii "
「神光? 」裝置90的激光能量由同軸雙程主放大器提供，同時增益飽和效應產生脈沖波形畸變也主要發生在主放大器階段，因此應用組合式角變反鏡（ avm ， angularvariablemirror ）獨立精密控制主放大器各路的增益性能是實現「神光? 」裝置精密化功率平衡的關鍵。 -
Lastly, many experiments are done on the base of simulation. output power, frequency, mode and pulse shortening phenomena of the microwave radiated from the device are analyzed during the experiment. the energy of microwave radiated from the device is calculated
最後在模擬的基礎上對該器件進行了詳細的實驗研究，分析了器件輸出信號的功率、頻率、輻射模式以及脈沖縮短的現象，同時還從能量的角度對器件輻射信號進行了分析。 -
The hardware circuit design include : industrial control computer configuration, selection of industrial control board type, design of the power supply and monitoring interface circuit, design of signal processing interface circuit ( the constant current source circuit, the time base signal processing circuit, the processing circuit for the signal to be measured ), design of panel control circuit, design of the system self - checking circuit, and etc. the program flow hart include : main program flow chart, system boot - strap self - checking program flow chart, manual static testing program flow chart, semiautomatic static testing program flow chart, automatic static testing program flow chart, dynamic testing program flow chart, transient testing program flow chart, source voltage and current monitor program flow chart, investigate function testing program flow chart, and etc. the measure system offers six working power supplies, the signal of time base, the signal of constant current source, sine wave signal and step to leap signal, and measures the frequency of the output pulse signal of the wide range pulse convert circuit accurately under three kinds of different test state ( static form, dynamic form and transient form )
硬體電路設計包括：工控機配置、工控板卡選型、產品電源及監控介面電路設計、信號處理介面電路（恆流源電路、時基信號處理電路、被測信號處理電路）設計、面板控制電路設計、系統自檢電路設計等。程序流程圖包括：主程序流程圖、系統開機自檢程序流程圖、手動靜態測試程序流程圖、半自動靜態測試程序流程圖、自動靜態測試程序流程圖、動態測試程序流程圖、暫態測試程序流程圖、電源電壓和電流監控程序流程圖、研究功能測試程序流程圖等。測試系統提供六路工作電源、時基信號、恆流源信號、正弦波信號和階躍信號，並對三種不同測試狀態（靜態、動態、暫態）下大量程脈沖變換電路輸出脈沖信號的頻率進行精確測量。 -
It is found from the experiment that under the conditions of peak magnetic field of 0. 57t, beam pulse fwhm ( full width of half maximum ) of 44ns, a microwave radiation pulse with fwhm 25ns and whole width of 35ns is produced, when the intensity of the guiding magnetic field rises, the peak microwave power changes little but the width of the pulse reduces. the a - k gap also has obvious influence on the microwave radiation, the stable and higher microwave output is obtained under suitable gap
實驗中還發現，在峰值磁場0 . 57t和束流半高寬44ns情況下，得到了25ns半高寬和35ns底寬的微波脈沖信號，隨著導引磁場增加，微波信號幅值基本不變，但國防科學技術大學研究生院學位論文是微波脈沖寬度會逐步減少;實驗中還發現磁場線圈位置有一定的軸向調節范圍，說明在磁場軸向分佈的一定變化范圍內，器件都可以正常工作，這對以後的永磁場系統導引的微波實驗有利。 -
（ 2 ） the major circuit has been established, composed of rectifier 、 buck - chopper 、 push - pull inverter and matching network, which realizes high - power supersonic ac output. to achieve maximal output power, the pulse frequency modulation ( pfm ) has been applied to auto - adjustment of output frequency, which corresponds to the load ' s resonant frequency
（ 2 ）建立了超聲電源主電路，其中包括：整流、直流斬波、推挽逆變器和匹配網路等部分，實現了大功率超聲頻交流電的輸出，輸出頻率的脈頻調制（ pfm ）和輸出功率的脈寬調制（ pwm ） 。 -
After the collection of experiment data, the model, whose input was pulse width and output was power, was identified in armax model type
採集實驗數據，以armax為模型類進行辨識，獲取了蹬踏運動時，以脈沖寬度為輸入、曲柄處功率為輸出的人機模型。 -
The design of excitation power source based on principle of three phase step motor and pulse width modulation ( pwm ) technology, intelligent power model ( ipm ) is used for inverter switches, the output ac pulse used as excitation signals. the speed of rotation and magnetic intensity can be changed by regulate the exciting converted frequency and magnitude of exciting current. constant current is achieved by closed loop feed back
勵磁電源結合步進電機原理與脈寬調制技術，選用智能功率模塊ipm作為逆變開關器件，輸出交流脈沖勵磁信號，以調節勵磁轉換頻率和勵磁電流大小為手段，實現對磁場旋轉頻率和磁場強度大小的有效調節，並通過閉環反饋實現閉環恆流控制。 -
Then, a power - combiner has an output power over 1watt and a power - combining efficiency of 83 % at 34. 2 - 35. 5ghz was realized. small - signal gain and saturated output power were measured under both continuous wave and pulse wave
利用小功率晶元設計8路開槽波導功率合成器，給出了連續波工作狀態與脈沖工作狀態的測試結果，包括通帶內小信號增益及飽和輸出功率。 -
In succession, the theory of chirped - pulse amplifier system is given in detail, firstly, studying from designing experimental light road and optical components to theoretical analysis, we par ' tly finished the system by ourselves. about ultr a - shoft pulse with a pulse - width of 9. 8f s and output power of 650mw and band - width of about l 20nm is output from oscillator source, secondiy, the stretching capacity of single grating four - pass stretcher is measured using abcd matrix combining collins function, and the effect of relativ e parameters to the streching ratio is also simulated. thirdly, a new type of disjunctional frequency moduiating function is provided according to the gain - narrowing and gain - saturation which are appeared in the co urse of amplification, under modulating the two effects are both controlled on some e xtent, fourthiy, the effect of ase that is often ignored by people is analyzed and the resolving methods are also given
從光路、光學元件的自行設計到理論分析計算，初步建立了一臺實驗系統；採用abcd矩陣法結合collins公式計算了四通式單光柵展寬器的展寬量，並模擬了相關參數對展寬比的影響，對實驗具有指導意義；評價了再生放大器和多通放大器的優缺點，對放大過程中通常忽略的放大自發輻射現象（ ase ）進行了分析，並提出了相應的解決方法；針對放大過程中出現的增益窄化和增益飽和現象，對輸入種子脈沖提出了一種新的分段頻率調制函數，實現了對增益窄化效應和增益飽和效應的共同抑制；提出了系統的材料（包括放大介質和光路中的普通介質）正是融合高階色散的來源。 -
Combined with electromagnetic and heat transfer, fem ( finite element method ) are used to analysis the temperature distribution in the output window result from pulse microwave and consecutive microwave of high power
用有限差分法對迴旋管輸出窗在連續波功率、脈沖功率條件下的溫度分佈進行了計算和分析。四 -
However, to suppress high order modes, bending multimode fiber will bring additional power wastage, which will affect the output characteristics of fiber amplifiers and fiber lasers, such as the gain and pulse energy
對多模光纖採取彎曲來抑制高階模的方法帶來了額外的功率損耗，這個額外的損耗對光纖放大器的增益以及輸出的激光脈沖能量都會造成影響。 -
A diode pumped cr4 +, nd3 + : yag crystal self - q - switched laser is demonstrated with fiber coupled ld and the imaging system. the pulse laser with 1064 nm wavelength is obtained. the maximum average output power is 3. 36 w, and the pulse duration is 65 ns, and the repetition rate is 87 khz, the opto - optical efficiency is 15. 3 %, the slope efficiency is 23. 8 %
用光纖耦合輸出的ld ，通過成像系統會聚，對二極體泵浦的自調q激光器進行了實驗研究，得到了平均功率3 . 36w ，脈沖寬度65ns ，重復頻率87khz的1064nm脈沖激光。 -
Among them, phase shifted ( ps ) full bridge ( fb ) zero - voltage - switched ( zvs ) pulse - width - modulated ( pwm ) dc / dc converter has strong competitive power in big power capacity fields. but it has some limitations such as smaller load range with zvs and larger circulation energy. the ps - fb - zvs - pwm dc / dc converter with a saturable inductor utilizes saturable inductor s critical saturable current characteristic and storage energy, to enlarge load range with zvs and improve output efficiency under light load
其中，移相控制零電壓開關脈寬調制dc / dc全橋變換器在大容量領域很有競爭力，但它具有實現零電壓開關負載范圍小，循環能量大等限制，帶飽和電感的移相控制零電壓開關全橋變換器利用飽和電感的臨界飽和電流特性及儲能，來擴大零電壓開關（ zvs ）的負載范圍，提高輕載時的輸出效率，具有非常重要的研究價值。 -
The paper describes a cw, non - cooling, digital all - solid - stated ld pumped nd : yvo4 driver which adopts microprocessor control, stability power of laser feedback and laser output power about 10mw. the system is composed of constant current source, soft diagram, protection, pulse schematic and laser power feedback loop. by combining appropriate hardware and software, we achieved, in our driver, a variety of protection features including the ability to suppress transients and reduce noise, relay soft and hardware over - current protection and overvoltage shut - off, we have obtained a continuously adjustable laser power output with high accuracy and stability
介紹一種採用單片機控制的連續運轉無製冷、數字式光反饋穩功率全固態激光器驅動電源，其輸出激光功率在10mw左右，系統包括恆流源、保護電路、脈沖驅動控制、光反饋穩功率控制等部分，結合硬體及軟體實現了激光二極體的可靠保護以及光功率穩定、準確輸出及在穩光輸出情況下，實現激光器的內外調制，並取得了一些有價值的研究成果。
分享友人