pulse-switching circuit 中文意思是什麼
pulse-switching circuit
解釋
脈沖開關電路-
Second, the results of theory analysis and simulation research show that the output of one cycle controlled bridge switching power amplifier have dc offset because of the nonideal characteristic of reset signal. the magnitude of output dc offset voltage is proportional to width of reset pulse. a voltage compensation technique is used to solve this question, and the computation formula of compensation voltage is gived. the circuit compensated and not are researched through simulation and experiment, which results show that compensated circuit solve the output dc offset effectively
其次，理論分析和模擬研究結果表明，由於復位脈沖的非理想特性，單周控制的全橋開關功率放大器輸出端存在直流偏置問題，其大小與復位脈沖的寬度成正比。針對輸出直流偏置問題，提出了電壓補償的改進方案，給出了補償電壓的具體計算公式。對補償前和補償后的方案進行了對比模擬研究和實驗研究。 -
There are five parts are as follows : in part one, the concept of switching function is introduced first to establish the nonlinear mathematical model of the induction motor variable frequency speed adjustment system which is fed by a sine pulse width modulated ( spwm ) inverter and takes the effect of the main magnetic circuit saturation into consideration, then the low frequency oscillation of the system is simulated according to the model. next, from the view point of energy conversion of the inverter - induction system, a criterion for the low frequency oscillation is proposed to determine whether the system is in low frequency oscillation which is judged by whether the interval of the negative current component of the inverter input current is more than 1 / fc ( fc is the carrier wave frequency of the inverter ) or not
首先引入開關函數概念，建立了正弦脈寬調制（ spwm ）逆變器供電異步電動機，考慮主磁路飽和時的變頻調速系統整體數學模型，模擬系統的低頻振蕩；其次從逆變器-異步電動機系統能量轉換角度出發，提出通過檢測逆變器輸入電流中負電流的間隔時間是否大於1 / f _ c （ f _ c為逆變器載波頻率）來判定系統是否出現低頻振蕩；最後的實驗結果驗證了系統低頻振蕩建模和判據的實用性和正確性。 -
For the inverter control circuit, the simulation model of 74hc4046 is established. two pulse signals can be obtained by forming dead time, which are used to drive the switching devices
對于逆變控制電路，本文建立了基於74hc4046的模擬模型，通過死區形成環節得到兩路觸發信號，去驅動主電路的開關器件。 -
Computer control unit produces the trigger pulses for the fast switching thyristors. fast switching thyristors are connected in parallels in order to meet the capacitance requirement of the circuit. trigger pulses produced by computer are amplified and isolated by three pulse transformers
設計三級脈沖變壓器來隔離和放大計算機產生的觸發脈沖，得到強觸發信號滿足了多個快速晶閘管並聯觸發的功率要求以及系統的抗反擊電壓的要求。 -
The main works are listed as follows : ( 1 ) based on the excitation of bi - directional current pulse technique, a new measuring circuit for weak variation of resistance was proposed for electrical resistance tomography. traditional ac current source is n ' t adopted as the exciting source. through fast bi - directional current switching, the polarization effects are eliminated
該電路主要優點如下：該電路沒有採用傳統的交流電流激勵法作為系統的設計原理，而是通過快速的正負極性電流切換來削弱直流電流激勵時激勵電極的極化效應，使通過直流法來測量氣液兩相流的電阻微弱變化成為可能。 -
At first, the development and fundamental of monolithic switching power supply are presented in this thesis. then a novel monolithic switching power supply circuit only with four terminals is analyzed at detail. it uses pulse skip modulation and current - mode topology
論文研究了一種作為psoc原型電路的四端單片開關電源電路，此電路採用新型的跨周期調制模式，與傳統的脈寬調制模式相比，提高了輕負載下的工作效率;整體控制迴路採用電流峰值控制模式。 -
The main circuit of the design in this article we used is fb zvs pwm dc / dc converter, full bridge zero voltage switching pulse width modulation dc / dc converter, which is a full bridge circuit composed of four power switches using resonance to implement zero voltage when turning - on or turning - off
本文設計的通信電源充電模塊的主電路採用的是fbzvspwmdc dc變換器，即全橋零電壓開關脈沖寬度調制的直流變換器，它是由4個功率開關管組成的全橋電路，利用諧振使每個開關管在零電壓的條件下完成導通和關斷。 -
High amplitude trigger pulse meets the power requirements of many thyristors connected in parallels. the voltage peak emerged in switching off inductance circuit is amortized by resistor and capacitor absorbed circuit
選取r = 54 ， c = 0 . 22 f的阻容緩沖吸收電路有效降低了快速晶閘管關斷感性負載產生的過電壓。 -
In the design of real - time control system, the paper takes three - phase full - bridge mosfet inverter as the real - time control main circuit, and adopts a control scheme with 120 ? switching mode combined with half - bridge pulse width modulation ( pwm ), which would avoid straightthrough short of a certain bridge. phase current is detected by single current sensor ; three - phase position signals generated by position sensors could not only supply commutation information for inverter, but also be used for speed detecting based on signals " period measurement, which makes the speed sensor unnecessary. the whole control system adopts speed and current dual closed - loop control strategy in order to construct a high performance rare - earth permanent magnetic brushless dc motor ( repm bldcm ) full - digital real - time control system
在實時控制系統的設計中，本文以三相全橋mosfet逆變電路作為實時控制主電路，採用120導通方式結合半橋pwm調制的控制方案，從而有效地避免了橋臂的直通短路；本文用單電流傳感器實現對相電流的檢測，來自位置傳感器的三相位置信號不僅為逆變電路提供換相信息，而且也用於基於信號周期測量的轉速檢測，這樣就省去了速度傳感器；系統採用的是速度、電流雙閉環控制策略，力求構建高性能的稀土永磁無刷直流電動機全數字實時控制系統。 -
First, this paper analyzes the principle of the snubber circuit of igbt inverter in detail, and the parameter of the snubber circuit components are derived. it also analyzes the twice voltage peak of the snubber circuit during the period of turnoff and discusses the impact of the parameter of the snubber circuit components on the waveform of turnoff. the reference materials for the snubber circuit design are proivided theoretically in this paper. futhermore. it analyzes a soft switching circuit that suits pulse power supply
本文首先從理論上詳細分析了igbt逆變橋緩沖電路的工作原理，推導出緩沖電路各元件的參數計算公式，分析了緩沖電路在關斷過程中的兩次電壓尖峰，討論了緩沖電路各元件參數對關斷電壓波形的影響，為緩沖電路的設計提供了理論上的依據。
分享友人