push valve 中文意思是什麼
push valve
解釋
底閥-
Insert a soft, blunt instrument into the valve end marked with the flow arrow and push the ball out of the valve end marked with the adj. arrow
用一個柔軟的、無稜角的工具插入閥門上標記flow (流向)箭頭的埠,將球體從閥門上標記adj (調整)箭頭的埠推出。 -
The valve can not bear the push, pull and torsion action generated by the heat - expansion and cold - contraction of pipe or other reason
盲板閥不得承受管道熱脹冷縮或其他原因發生的外力對其產生推拉、扭曲作用。 -
When the electrohydraulic push rod works, if the external force suffered by the piston rod is more than the setting output torque, the piston moves to the end ; oil pressure in the oil pipeline increases rapidly to the setting value, the safety valve overflows rapidly, to achieve overload protection
電液推桿工作時,當活塞桿所受外力超過調定的輸出力距活塞運動到終點;油路中的油壓迅速增高至調定值,安全閥迅速溢流,實現過載保護。 -
When the temperature to gas pipelines, temperature packets of material expansion, the pressure rise, inflation pressures are rising corrugated box, corrugated promote the expansion thrust to overcome the spring - loaded pole resistance, the ball - type valve opened for big change ; when the gas pipeline to reduce the temperature, temperature of the material swelling up, the pressure lowered inflation corrugated box pressure also reduced, spring - loaded pole compressed corrugated of resistance to thrust, spherical valves open for smaller ; this constant push and pull adjustment for the balance, as long as refrigeration cycle continue
當回氣管道溫度升高,感溫包內的物質膨脹,壓力升高,膨脹波紋箱內壓力也升高,波紋腔膨脹推動推力桿克服彈簧阻力,球型閥開度變大;當回氣管道溫度減低,感溫包內的物質膨脹,壓力降低,膨脹波紋箱內壓力也降低,彈簧阻力推動推力桿壓縮波紋腔,球型閥開度變小;如此不斷的進行推拉調整平衡,只要製冷循環繼續下去。 -
Instead, the motor rotate reversely, push rod ( piston rod ) push out, the valve plate closes, stops discharging
反之,電機反轉,推桿(活塞桿)推出,閥板關閉,停止卸料。 -
The check valve and relief valve seats shall be push - in type
這種止回閥和安全閥閥座應該是推入式的。 -
Using the centerline access bar, spin the check assembly from the 9 o ' clock position to the 12 o ' clock position, then ( without letting go of the access bar ) push the cam assembly slightly downstream so that the clapper is now parallel to the valve body
用中心線接近棒將止回閥總成從時鐘指針9點的位置旋轉到12點的位置,然後(不要松開接近棒)將凸輪總成稍微往下游推使得閥瓣與閥體平行。 -
Insert a soft, blunt instrument into the downstream end of the valve and push the ball and seal carrier out of the upstream end of the valve
將柔軟的、鈍的工具插入閥門的下游埠,將球體和密封托架從閥門的上游埠推出。 -
When discharging, the motor operates, hydraulic cylinder charges pressure, push rod ( piston rod ) draw back, the valve plate connected with push rod opens, the materials are discharged
當需要卸料時,電機運轉,液壓缸增壓,推桿(活塞桿)收回,和推桿連接的閥板開啟,物料卸下。 -
The groove around the seat permits the gate to push particles aside and prevents clogging. when the valve is open the flow cleans the groove
閥座周圍的槽使得閘板能夠把顆粒推到旁邊,避免產生堵塞。當閥門開啟時,通過的流體對槽進行清洗。 -
Electrohydraulic push rod drives the two - way pump to output pressure oil with rotation of motor clockwise and counter - clockwise, by control of hydraulic valve, send to the hydraulic cylinder, to achieve the reciprocating movement of the piston rod
電液推桿以電動機正反轉,帶動雙向泵輸出壓力油,經液壓閥控制,送至液壓缸,實現活塞桿的往復運動。
分享友人