put on pump 中文意思是什麼
put on pump
解釋
在井口裝泵；使油井開始用泵產油-
C put the pump - set on to the base, between the soleplate and the base placed binate cuneal mat, pass adjusting cuneal mat to find the level of pump accurately
3將機組放在基礎上，在底板和基礎之間放成對楔墊，通過調整楔墊，找正泵的水平。 -
It ’ s a medical treatment equipment of high capability but low price. this thesis chooses a discal peristaltic pump and put forward amelioration schemes based on analysis of trait of transfer pump in common use presently and selects stepper motor as drive motor. in order to reduce the whole volume, the pcb board integrates stepper motor drive circuit, keyset, alarm circuit and lcd
本文在分析目前常用輸液泵的優缺點的基礎上，選擇dg - 1盤狀蠕動泵，並進行了結構改進;選擇步進電機作為輸液泵的驅動電機，為縮小整體的體積，將步進電機的驅動電路、按鍵、 lcd和報警電路集成到單板上。 -
For example, a batch of large and medium - sized key projects such as the yamzhog yumco pump storage power station and the norbusa chromite mine in shannan are put under strict supervision and management in accordance with the law on environmental protection ; the garbage dump located close to the lhasa river was moved to another place to minimize water pollution, and polluted water treatment centers were set up
為保護生態環境，環境保護部門採取了一系列措施，如對正在興建的羊卓雍湖電站、山南羅布薩鉻鐵礦等一批大中型重點工程，嚴格依照環境保護法進行監督和管理；搬遷距拉薩河不遠的垃圾場，以減輕對拉薩河的污染；建立污水處理場等。 -
( 2 ) in this paper, the author summarized the working principle, the superiority and the limitations of a few main kinds of classical sprinkler systems ; put emphasis on the importance of a few key points which is relevant to the function of the system, such as the choosing of sprinkler and it ' s fixing, the automatic checking function of water pump, the layout of alarm valve, especially the choosing of sprinkler and it ' s fixing ; looked through the feasibility of which we used water instead of gas by water mist especially finely divided water mist fire - extinguishing technique
展望了水噴霧技術特別是細水霧技術進行以水代氣滅火的可行性。 （ 3 ）針對工程設計中最復雜，工作量最大的部分-系統水力計算部分，在規范的基礎上，基於excel電子表格，提出了經濟流速的范圍，提供了一套行之有效的設計計算方法，同時，對屋頂水箱和增壓泵的設置這一難以解決的問題發表了見解，既確保了自動噴水滅火系統初期快速滅火、控火的性能，又節省了大量的設計工作時間。 -
It is pointed out that passage hydraulic loss is related to the flow circulation, the influence of flow deviation on passage hydraulic loss and pump assembly efficiency is analyzed, the forming mechanism of flow deviation is investigated, and the method of eliminating flow deviation is put forward
指出流道水力損失與水流環量有關，分析偏流對流道水力損失和泵裝置效率的影響，研究偏流形成機理，提出消除偏流的方法。 -
Through the statistic analysis on the change of the melt gear pump working condition pre - and post - pet plant capacity increasing and concatenate direct spinning process, the reasons for the unsteady running were studied, the modification measures such as lubricating the oil groove with sliding bearing, mechanical sealing of the gear pump, decreasing the gear pump outlet pressure, changing the automatic speed increasing to hand speed increasing were put forward
摘要通過對聚酯裝置增容和後接直紡長絲前後熔體齒輪泵工況變化的統計分析，研究其運行不穩定的原因，提出改造措施，包括滑動軸承潤滑油槽，齒輪泵的機械密封，降低齒輪泵出口壓力，改自動提速為手動提速等等。 -
From the viewpoint of the characteristics of two - phase liquid sand slurry wear, combined with the examination and study on easily damaged workpieces, the wear failure ' s basic rules are pointed out, of the pump shell and the cutter - piece on service, and the general principles of material wear - resistant designs put forward. the sand slurry abrasion tester has been designed and developed which can simulate general dredging conditions. summarized and presented are the position - exchange measuring method of sand slurry abrasion test and the experiment specification of sand slurry wear test of dredging conditions
文中系統論述了作者在疏浚工況泥沙磨損機理及其耐磨新材料課題研究中的工作成果，主要研究內容和創新點如下：總結分析了磨損研究動態和提高材料耐磨性的方法；從兩相流泥沙磨損的特點出發，結合對失效易損件的考察研究，分析指出了現役泥泵殼和絞刀片磨損失效的基本規律，提出了材料耐磨損設計的基本思想；設計研製了能模擬疏浚工況的泥沙磨損試驗機，總結提出了泥沙磨損試驗換位測試法和疏浚工況泥沙磨損試驗規范。 -
Based on the technical requirements of manufacture, application and repair of the pump shell and cutter piece of the cutterhead pipeline dredge, put forward are the re - manufacture three principles on easily damaged workpieces of dredge engineering. with the inter - clamped structures on the pump liners, the gradient wear - resisting design on the cutter piece, and the new techniques in the process of re - manufacture, new wear - resistant materials, including high - cr alloy, overlaying and brazing deposits, and polymer adhesive coatings have been successfully applied to the re - manufacture dredge pump shell and cutter piece. the application results show that their wear - resistant lifetimes and the dredging profits have been increased remarkably
根據絞吸挖泥船泥泵絞刀的製造、使用和修復性能要求，提出了疏浚工程易損件再製造三原則；採用泥泵內襯互鎖結構、絞刀梯度化耐磨設計和工藝再製造新技術，將高鉻合金耐磨材料、熔敷耐磨材料及其復合材料和高分子耐磨膠粘塗層材料成功地應用於再製造泥泵殼和絞刀片上，顯著提高了泥泵殼和絞刀的耐磨壽命和挖泥船的疏浚效益。 -
We have successfully developed, researched and produced concrete expansion agent, high performance water - reducing agent, pump - sending agent, quick - coagulating water - reducing agent, high performance concrete mixing material, green environmental senior inner wall putty, pcc spring concrete waterproof coating and so on. our series products have gained high fame among our clients after being put into market
幾年來，經過我們的共同努力，我公司成功地開發研製生產了混凝土膨脹劑，高效減水劑緩凝減水劑泵送劑早強減水劑高性能混凝土摻合料綠色環保型高級內墻膩子粉和pcc彈性水泥防水塗料等20多個品種。 -
Abstract : conventional ship propulsion methods meet some limitations in ship development towards high - speed, large - scale and high - power. a new ship propulsion method, integrated hydraulic propulsion ( ihp ), was put forward to solve the problem. then further research work was done on the principle of ihp method. working condition - matching characteristic was discussed through the working condition matching characteristic chart. after that, the advantages and disadvantages of ihp method were given. and the pump and motor, important parts of ihp, was designed through physical analytical method. ihp method can be used extensively in some special kinds of ship for its own characteristics. to a certain extent, the limitation problem of ship propulsion method can be solved. ihp method diversifies the existing ship propulsion methods
文摘:為解決船舶在向大型化、高速化方向發展時船舶主機設計困難，機艙布置不合理以及機動性能差等問題，提出了一種新型船舶推進方式，即船舶綜合液壓推進.給出了該推進方式的推進原理，通過工況配合特性曲線圖，對其工況配合特性進行分析，對該推進方式的優缺點進行討論並對其重要組件液壓泵以及馬達進行設計計算.結果表明船舶綜合液壓推進具有其獨特的優點，是對現有船舶推進方式的有益補充 -
Conventional ship propulsion methods meet some limitations in ship development towards high - speed, large - scale and high - power. a new ship propulsion method, integrated hydraulic propulsion ( ihp ), was put forward to solve the problem. then further research work was done on the principle of ihp method. working condition - matching characteristic was discussed through the working condition matching characteristic chart. after that, the advantages and disadvantages of ihp method were given. and the pump and motor, important parts of ihp, was designed through physical analytical method. ihp method can be used extensively in some special kinds of ship for its own characteristics. to a certain extent, the limitation problem of ship propulsion method can be solved. ihp method diversifies the existing ship propulsion methods
為解決船舶在向大型化、高速化方向發展時船舶主機設計困難，機艙布置不合理以及機動性能差等問題，提出了一種新型船舶推進方式，即船舶綜合液壓推進.給出了該推進方式的推進原理，通過工況配合特性曲線圖，對其工況配合特性進行分析，對該推進方式的優缺點進行討論並對其重要組件液壓泵以及馬達進行設計計算.結果表明船舶綜合液壓推進具有其獨特的優點，是對現有船舶推進方式的有益補充 -
The flow of every pump is inclined to be different in the same side - inlet sump and the poor flow pattern, and then the inlet condition of the pump is not good, which makes the efficiency of the pump drop and causes vibration etc. based on the theses on the hydraulic characteristic of the wenshui road pumping station in the third period shanghai disposal sewage project, the methods were discussed to improve the flow pattern of side - inlet sump, and the measures were put forward to ameliorate the flow pattern in the paper
對側向進水集水池，一般會出現同池各水泵配水不均勻，池內流態紊亂、水泵吸水條件差，繼而導致水泵效率下降、機組振動等問題。本文結合上海市污水治理三期工程汶水路泵站水力特性研究課題，探討了改善側向進水集水池水力特性的途徑與方法，提出了有效的整流、均流措施。 -
Several transient simulation programs have been developed based on the models above, and were put into practice of the transient simulations of following : ( 1 ) autoregulation on water height of the fore bay in single pump station, and the influence of governor parameters ; ( 2 ) autoregulation on output of adjustable - blade pump in single pump station, and the influence of governor parameters ; ( 3 ) on - line autoregulation on flow equation of multilevel pump stations system
本文應用上述方法編制了過渡過程模擬程序， （ 1 ）進行了單級泵站中轉槳泵在線自動調節泵站前池水位的動態模擬計算，並對調節參數的影響做了比較研究； （ 2 ）進行了單級泵站中轉槳泵在線自動調節泵輸出流量的動態模擬計算，並對調節參數的影響做了比較研究； （ 3 ）進行了多級泵站中轉槳泵在線自動調節輸水系統流量平衡的動態模擬計算。 -
A new type of double - acting contactless sliding - vane pump was put forward to the defect analyzed on sliding - vane, which uses roller to control the locus of sliding vane to insure the minute gap between the stator and sliding vane
摘要通過分析滑片泵存在的缺陷，提出了一種利用滾柱控制滑片運動軌跡，使滑片與定子內表面保持微小間隙的新型雙作用無接觸滑片泵。 -
Because reciprocating pump has complicated structure and more exciters, so its signal is a strong non - stationary signal, and carrying out fault feature extraction and diagnosis is very difficult to it, this text mainly researches on featute extraction of reciprocating pump ’ s valve vibration signal. this text introduces hht that huang put forward, it is a kind of signal processing method that suits for dealing with the stationary signal, and suits for non - stationary signal also. although the hilbert - huang transform ( hht ) is an effective tool processing the non - stationary signal, the hht based on emperical mode decomposition ( abbreviated as emd ) algorithm which adopts the cubic spline interpolation could n ' t acquire accurate characteristics for the strong non - stationary signals in that the spline produces an accurate result only under the condition that the data consists of values of a smooth function
本文引入了huang等人提出的hht ， hht是一種既適合於處理平穩信號也是一種適合於處理非平穩信號的信號處理方法。盡管希爾伯特-黃變換（ hht ）是處理非平穩信號的有效工具，但基於經驗模態分解（簡稱emd ）的hht由於採用三次樣條插值而不能準確提取強非平穩信號的特徵，因為三次樣條插值只有在數據由光滑函數值構成的情況下才能產生精確的結果。為了解決這個問題，本文提出了基於改進的emd演算法，即採用分段三次hermite插值多項式（ pchip ）作為極值包絡的方法。 -
According to the supply system composed by parallel connection water pump, many kinds of operation proposals in a single pump were put forward to provide the greatest possible flow on both sides of the demarcation point in the scope of the flux changes ; identified the system of pumps, electromotor, speed governor imitate method of characteristics curve of the power device and its rotating speed, efficiency, energy consumption calculation under different condition ; the analytical methods used for the operational plan for comprehensive evaluation of the economic and safety and optimal results
摘要針對由並聯水泵組成的供水系統，提出了在以單泵可能提供最大流量為分界點的兩側流量變化范圍內具有多種運行方案；確定了在不同工況下，該系統中水泵、電機、調速器特性曲線的擬合方法及其各動力裝置中轉速、效率、能耗的計算式；採用解析的方法對各種運行方案進行了經濟性和安全性綜合評價，並給出最優結果。 -
The paper employs the method of three stage design to make analysis on the pneumatic turbine system of the mine pneumatic pump in theory and put it into experiment on the base of the kfb30 - 18 mine pneumatic pump
本課題採用三次設計方法，以kfb30 - 18型礦用風動水泵為基礎，對該產品的風動渦輪系統進行了理論分析和實驗研究。
分享友人