real radius 中文意思是什麼
real radius
解釋
（齒輪）實際半徑-
In the non - coaxial bwo of l - band, the radius of the slow - wave structure is very large, and the volume and weight of the guiding - magnetic system are also very large. thus, the non - coaxial bwo of l - band is bulky and lumbersome and is inconvenient for real application
若採用非同軸相對論返波振蕩器實現l波段的微波輸出，則要求慢波結構的平均半徑很大，導引磁場系統的體積和重量會變得較大，這給器件的小型化帶來了很大的困難。 -
Based on in - depth analysis on characteristic and function principles of psd, combined with characteristic of measured object, this article presents an new real - time measurement for symmetrical degree, guiding - groove, twining angle, inside radius of long direction pipe ; completes designing work for hardware of function module and application software ; and gives analysis and computation on error sources and uncertain - degree of measure result. based on above work, this article develops a parameter - auto - chosen, integrated and automatic measurement device for beeline degree, guiding - groove symmetrical degree, twining angle and inside radius of long direction pipe
本文在深入分析研究psd的特點和工作原理的基礎上，結合被測量對象的特點，首次提出了長定向管導槽對稱度、纏角、內徑等實時自動化測量的一種新方法；完成了硬體功能模塊及應用軟體的設計工作；並對測量結果的誤差源及不確定度進行了分析和計算；在此基礎上研製了長定向管的直線度、導槽對稱度、纏角及內徑等參數自動、實時綜合測量設備。 -
Precision measurement method for spatial cams and probe - radius compensation method are presented in this paper according to spatial cam characteristics, and a specified measure program that can realize real - time probe - radius compensation is programmed
摘要根據空間凸輪的特點，給出了空間凸輪精密測量及剛球半徑補償方法，並編制了可實現實時測球半徑補償的空間凸輪專用測量程序。 -
At the same time, for the equidistant surface in practical measurement, special search method is applied for automatic segmentation, so the normal vector of the data at arbitrary position of the space is solved, then radius compensation of probe is implement. so the return is realized from equidistant surface to real measurement surface
針對實際測量中得到的等距曲面，採用空間搜索的方法對數據點分塊，求取了任意測量點法矢，提出了測頭半徑的補償方案，從而實現了由空間等距曲面到被測曲面的復原。 -
According to the rheological properties of melted abs filament during extrusion from fdm ' s nozzle, on the basis of research on extruded filament section shape, the compensation model of ideal contour line is established, and a new technique for compensating inner or outer contour line of workpiece is put forward, which should depend on the real width of extruded filament ( instead of nozzle radius ) and the real dimensional shrinkage of workpiece
根據abs絲從噴頭擠出過程中的流變性能，在研究fdm工藝噴頭擠出絲截面形狀的基礎上，建立了理想輪廓線的補償模型，並提出了根據擠出絲實際寬度（而非噴嘴孔直徑）和零件尺寸實際收縮量補償零件內、外輪廓的新方法，驗證試驗結果表明該補償模型和補償方法正確可行。
分享友人