remaining error 中文意思是什麼
remaining error
解釋
剩餘誤差-
When the instruction is to exit, the server terminates the execution of the remaining requests as soon as an error is encountered, and all the requests that do not execute are marked as failed
如果要求退出，一旦遇到錯誤，服務器就終止剩餘請求的處理，所有未執行的請求都標記為失敗。 -
The fem model was accurate and effective by using submodel and error estimation technique that ensured the reliability of calculation and analysis. the thesis got the measure of critical flaw and designing life of the girder. in addition, the thesis calculated the remaining life of the girder while the flaw reaching 150mm
結合有限元分析結果和損傷容限設計方法，本文計算了馬鋼第三煉鋼廠4 # 125t鑄造起重機主梁下蓋板的臨界裂紋尺寸，及初始裂紋為0 . 5mm時主梁的設計壽命，並估算了在裂紋尺寸達到150mm時主梁的剩餘壽命。 -
A new lom process, in which the slice sheet is cut along the tangent of normal section line in z - axis direction, is proposed to reduce the theoretical manufacturing error and remaining material quantity
為減小造型誤差，提出了新lom方法，即沿過分層板中點造型曲面z向法截線的切線切割分層板。 -
This algorithm improves confidence in se by estimating parameters and states at the same time. simulation results on test power systems which range in size from 4 to 118 buses, have shown the virtues as follows : getting unbiased estimation without detecting and identifying bad data in measurements ; solving state and parameter estimation for power system with good convergence and excellent robust property ; increasing the numbers of iterations a little bit with the test systems expanded ; estimating many transformer taps simultaneously and remaining the main state estimation ; keeping the estimated relative error within + 0. 1 % and processing efficiently equality constraints and ill condition with polynomial complexity
對ieee ? 4 118節點系統和廣西主網進行的模擬結果表明： l1范數估計具有不良數據拒絕特性，當量測量中存在不良數據時，該演算法在不經檢測和辨識不良數據情況下仍是無偏估計，具有良好收斂性，所需迭代次數隨著問題規模擴大而增長極小；能夠同時估計多個變壓器抽頭，並保持狀態估計主體；在滿足可觀測性條件下，估計的相對誤差保證在0 . 1以內；能夠有效處理等式約束和病態條件，並具有多項式時間性。 -
Modeling surface is approached by stair up of lines in the current lom process, so theoretical manufacturing error and remaining material quantity are greater. the higher precision and lower remaining material quantity are ensured by using the thinner slicing thickness
本文指出現有lom方法由於用直線臺階逼近造型曲面，因而原理加工誤差大，殘留加工量多，必須使用較薄的分層厚度來保證較高的造型精度和較小的殘留光整加工量。 -
The effects of new lom process can increase the thickness of the laminating layer from 0. 05 - 0. 10mm to 1. 0mm grade, almost same or lower theoretical manufacturing error and remaining material quantity than current lom process can also be gotten
在理論造型精度和殘留加工量相近或更佳精度的條件下可以將分層厚度從現有的0 . 05 - 0 . 10mm提高到1 . 0mm數量級。
分享友人