reset switch 中文意思是什麼
reset switch
解釋
復位電門-
If this output does not switch between h and l anymore a hard-ware reset is produced and the processor is initialized again.
如這個輸出不再在高電平和低電平間作切換，硬體復位就會產生，並將處理器再次初始化。 -
Sole - switch 2. dual - switch 3. completely opening or closing types by leftward and rightward roating, all are able to auto matically reset
1 .單開關2 .雙開關3 .左轉右轉均可完全斷開或閉合 -
In the hardware design, the paper completes modules ’ design like outside memory, patulous a / d, patulous d / a, rs232 communication, ecan communication, led control, keyboard control, distant control, emulation, reset, logic voltage switch, dsp supply power regulate and ac - dc power circuit, as well as room layout design like anterior panel, back panel etc. and dsp transfers data with peripheral equipments except outside memory using serial ports. besides, the whole circuit is configured in interrupt response. thus, it can meet system demand as well as take full advantage of tms320f2812 ’ s hardware resource. in the software design, the paper finishs programs like the interface programms intercommunicates with people, the distant control program, ad and da modules ’ control program, in addition, the paper select the velocity and acceleration state - feedback algorithm and is written in the program. the software design uses dsp integrate exploiting environment named ccs2. 2 of ti inc. as software instrument, and programs with the combination of c language and assembly language. moreover, in order to maintenance or modify the software expediently and shorten software ’ s exploitation time, the design adopt software modularization technique. finally, some air cylinder experiments are carried out to proved that the pneumatic controller is very practical
在硬體設計中，本文完成了片外存儲器擴展、 a / d擴展、 d / a擴展、 rs232通信介面、 ecan通信總線介面、液晶顯示控制、鍵盤控制、遠程控制、模擬、復位、邏輯電平轉換、 dsp工作電源校正電路和ac - dc電源等模塊設計以及控制器前面板、後面板等的空間布局設計。其中dsp與除外部存儲器的外圍設備之間的數據傳送全部採用串口通信，同時系統電路配置成中斷響應方式，這樣既滿足了系統要求，又充分利用了tms320f2812的硬體資源。在軟體設計中，本文完成了人機界面功能模塊、遠程控制模塊、 ad擴展模塊、 da擴展模塊、速度和加速度狀態反饋的控制演算法的程序設計。 -
The cutting machine does not reset when turning on the switch
打開電源開關切割機不復位 -
It has a reset button, a switch which i think turns the ethernet port into an uplink port, and a power button in front
它有一個重置按鈕，一個開關（我認為它將以太網埠轉換為上行埠） ，以及一個電源按鈕（在正面） 。 -
Cv - 05 reset function instead of. power switch on - off, or short mother board
碰觸主機板上的reset pin -
Mode switch ： peak is the peak value of load ; can cleard by reset button. track reads changes corresponding to load variations. canceled by releasing the load
方式開關：峰值檢測（ peak ） （由復位按鈕清除保持的測量峰值）和跟蹤檢測（ track ） 。 -
The detector head to adjust the operation distance from80to 120 i. e. 0. 8mm to 1. 2mm. after the setting is completed, press the set switch to reset
也就是0 . 8mm至1 . 2mm ，設定完成後再按設定開關復原。 -
These studies in the thesis have been done as follows : it is proved that if the three - phase single - switch boost type power - factor - correction can work in continuous - current - mode, its power factor can not reach unity. therefore, it is not qualified for high power and high requirement application. according to the ac side equivalent circuit of the three - phase three - switch boost type power - factor - correction, the equations to realize unity power factor have been deduced and realized by integrate - reset - control circuit
本論文把積分復位控製成功應用於三相功率因數校正技術中，作了以下幾方面的研究： 1 .從理論上證明了三相單開關boost型pfc即使工作在ccm ，其功率因數也不能達到1 ，在大功率和對功率因數校正能力要求較高的場合，三相單開關boost型pfc達不到要求， 2 .根據三相三開關boost型功率因數校正交流側的等效電路，推導出實現單位功率因數所需的控制方程，並用積分復位控制電路進行實現，在理論研究的基礎上進行了模擬研究。 -
The apfs using according detection method are investigated and developed by simulating and experimenting to demonstrate the performance of the proposed detection method and apf. secondly, a nonlinear, large signal control theory - one cycle control, which was presented in the 90 ' s and suitable especially for switch power converter ， was investigated. the integration reset control and extension applications ， which was < wp = 7 > developed based on one cycle control theory, was emphatically studied
本文深入分析了90年代初發展起來的一種適合開關變換器的大信號非線性控制理論? ?單周控制（ onecyclecontrol ）理論，以及在此理論基礎上發展起來的常頻積分復位控制技術和它的最新應用，首次成功地將單周控制理論應用於apf的檢測和控制中，提出並實現了一種通用常頻積分復位控制有源電力濾波器，從而簡化了apf的工作原理和結構。
分享友人