resin wear 中文意思是什麼
resin wear
解釋
樹脂脫落-
Effect of antifriction on friction and wear properties of resin - based composite
減摩組元對樹脂基閘片摩擦磨損性能的影響 -
It is showed that by using the phenolic resin and the fiber, the clutch friction materials could be manufactured with good properties such as stable friction coefficient, low wear rate, high fade resistance at 350, and suitable porosity
結果表明，採用三組份酚醛樹脂和混雜纖維可以制備出摩擦性能良好， 350不發生熱衰退的離合器摩擦材料，且材料具有合適的孔隙率。 -
And another brake material formula also can be achieved in which the carbon fiber was replaced by the wood fiber based on the researching of the effect of fibre, resin and filler in multi - fibres hybrid composite test result shows that the formula material have a relatively suitable friction coefficient ( ranging around 0. 35 ), good fade resistance and recovery as well as low wear ratio. by comparing the formula material with the product of national and abroad sold in the market, its low cost and excellent properties make a bright prospect
在研究各種纖維、樹脂和填料對混雜纖維復合摩擦材料摩擦學性能影響的基礎上，本文研製開發出分別適用於中重型車與中小型車用的剎車摩擦材料的最佳配方和一種含木纖維的多種纖維混雜復合摩擦材料的最佳配方。將所選配方的剎車材料與市售的國內外品牌剎車片進行對比，結果表明本課題所開發研製的摩擦材料的摩擦系數都在0 . 35左右，具有很好的摩擦系數穩定性和抗熱衰退性，磨損率也較小，綜合考慮到配方試樣原料成本較低，在性價比上具有一定的優勢。 -
The tlow distance and gelating time of the nanocomposites were shorter than that of the pure pf, which meet the standard of the pf used in frictional materials. compared to the pure pf, the silica7pf nanocomposites exhibited excellent heat stability only in nitrogen atmosphere, however, so do vermiculite / pf nanocomposites in both nitrogen and air atmospheres. compared to the brake pad based pf resin, the wear rate of the present one based with silica / pf nanocomposite decreased obviously, especially in high temperature
用烷基銨ctab和kh - 560對蛭石進行有機化處理，通過原位聚合法制備了酚醛樹脂接枝改性sio _ 2納米復合材料、酚醛樹脂kh - 560改性sio _ 2納米復合材料、酚醛樹脂ctab改性蛭石納米復合材料、酚醛樹脂/ kh . 560改性蛭石納米復合材料，採用ftir 、 xrd 、 afm和tg分析與流動距離、凝膠化時間的測試，研究了所制備的酚醛樹酯納米復合材料的結構、固化行為和熱穩定性能，並研究了以酚醛樹酯納米復合材料為基體的剎車片摩擦磨損性能。 -
Remove paint, sealing layer ( protection layer ), resin emulsion cement ( wear - resisting flooring ), protruding part, rain trace, trowel mark, rough surface, uneven joint etc
去除油漆、密封層（保護層） 、膠脂水泥（耐磨地坪） 、高出部分、雨跡、鏝刀痕、粗糙表面、不平接縫等。 -
Some problems in development and application of novel epoxy resin - based lubricative and wear - resistant coatings
新一代環氧潤滑耐磨塗層研製與應用中需解決的若干問題 -
406 is non - asbestos clutch facing which adopts refined glass fiber, high - temperature resistance composite fiber materials, high quality metals such as soft copper and so on, uses imported wear and lubrication materials, high grade heat resistance resin binder through special process
406無石棉離合器面片，採用精製玻纖，耐高溫復合化纖材料，優質軟金屬銅等，選用進口耐磨材料，潤滑材料，高檔耐溫樹脂經過特殊工藝復合粘結而成 -
405 is non - asbestos clutch facing which adopts refined glass fiber, high - temperature resistance composite fiber materials, high quality metals such as soft copper and so on, uses imported wear and lubrication materials, high grade heat resistance resin binder through special process
405無石棉離合器面片，採用精製玻纖，耐高溫復合化纖材料，優質軟金屬銅等，選用進口耐磨材料，潤滑材料，高檔耐溫樹脂經過特殊工藝復合粘結而成 -
With strong ability on the r d, the company owns three patents : the production technology of color quartz sand, the production technology of glass marble, an installation method of a new type decoration board and a special technique : the production technology of microcrystalized wear - resisting miniball. bonanas main products include : color quatrz sand for epoxy flooring system, grinded quartz sand powder, high - grade artificial color quartz sand for wall decoration, various natural and artificial cobblestone, super fine quartz powder, grinding medium of quartz miniball, color quartz sand paint or sand wall paint, color sand lacquer, transparent epoxy resin paint especially for color quartz sand floor and self - leveling epoxy paint for color quartz sand
新材料技術有限公司位於北京市通州區張家灣鎮，是一家集產品開發生產銷售於一體的高新技術企業，擁有博士碩士等高級人才，具有強勁的產品研發和生產開發能力，目前，公司擁有： 「彩色石英砂生產工藝技術」已申請國家專利「微晶化處理耐磨微球生產工藝」 「玻璃大理石製造工藝」已申請國家專利「一種新型裝飾板材安裝工藝」已申請國家專利等多項國家專利和自主開發的生產工藝技術。
分享友人