resistivity measurement 中文意思是什麼

resistivity measurement 解釋
電阻率測量
  • resistivity : n. 抵抗力；抵抗（性）；【電學】電阻率；電阻系數，比阻。
  • measurement : n. 1. 測量，計量，量度。2. 份量，尺寸，大小，寬度，厚度，深度（等）。3. 測量法。 measurement goods （按體積、容積計算的）體積貨物。
  1. Standard test method for measurement of soil resistivity using the two - electrode soil box method

    使用雙電極土壤箱法測量泥土電阻率的標準試驗方法
  2. Testing of semiconductor materials ; measurement of the resistivity of silicon or germanium single crystals by means of the four probe direct current method with collinear array

    半導體材料的試驗.用探針直線排列的四探針直流法測
  3. Tan insulating liquids - measurement of relative permittivity, dielectric dissipation factor and d. c. resistivity

    絕緣液體.相對電容率電介質損耗因數
  4. Tan insulating liquids - measurement of relative permittivity, dielectric dissipation factor tan delta and d. c. resistivity

    絕緣液體.相對電容率電介質損耗因數
  5. Eddy current decay method for measurement of resistivity and residual resistance ratio of pure metals

    純金屬電阻率與剩餘電阻比渦流衰減測量方法
  6. So in one hand it requires the wafer ' s diameter to be more large in order to enhance the productivity, and on the other hand it puts forward more strict requirement about the crystal perfection and electricity character. especially the electronic character and the equality of micro - area in the crystal wafer has become the key factor to determine whether the device can be made on it or not. so the resistivity measurement of micro - area become one most important procedure in the chip machining. to ensure the produce quality of chip and the perfect performance of final production, the four - probe testing technology need to be deeply studied

    圖形日益微細化，電路尺寸不斷縮小，目前ic製造以8英寸、 0 . 13 m為主，預計在2007年左右將以12英寸、 65nm為主，這一方面要求圓片直徑不斷增大以提高生產率，另一方面對晶體的完美性、機械及電特性也提出了更為嚴格的要求。特別是微區的電學特性及其均勻性已經成為決定將來器件性能優劣的關鍵因素。因此，微區電阻率的測試成為晶元加工之中的重要工序。
  7. Test methods for determining electrical properties of electric cables and wires. measurement of resistivity of metallic conductive materials

    電線電纜電性能試驗方法金屬導體材料電阻率試驗
  8. Measurement of electrical resistivity and thermopower of liquid metals

    液態金屬電阻率及熱電勢的測量
  9. Method of measurement of resistivity of metallic materials

    金屬材料電阻率測量方法
  10. The measurement of dielectric loss and volume resistivity is effective preventive tests to judge insulating oil isolation status of polluted and aging, and it ' s important method of ensuring the safe operation of transformer and oil - filled circuit breaker, etc. however, the measuring systems of insulating oil dielectric loss and volume resistivity used at present exist the shortcoming of low accuracy, weak repeatability, inconvenience, and its thermostatic control system ca n ' t meet the challenge

    絕緣油的介質損耗因數、體積電阻率測量，是判斷絕緣油的劣化與污染程度的有效預防性試驗，是保障變壓器、油斷路器等充油電力設備安全運行的重要手段。然而，目前所使用的絕緣油介質損耗因數、體積電阻率測試系統存在著測量精度低、測量結果重復性不好、控溫系統不能滿足控溫要求、操作不便等缺陷，針對這一現狀，本文對絕緣油介損及體積電阻率一體化測試系統進行了研究。
  11. Resistivity measurement for carbon fiber reinforced concrete

    碳纖維增強水泥的電阻測試
  12. In the measurement of the high density resistivity method, there is often some false data in the data section because of the influence of poor earth contact of electrodes and other interference factors etc., which can cause false abnormality of data section and make data interpretation difficult

    摘要針對在高密度電阻率法測量過程中，數據斷面易出現突變點，而造成電阻率擬斷面圖虛假異常，難以準確解釋的情況提出了一種快速、高效的剔除突變點的方法。
  13. A research scheme is carried out and cfrc bars are made to investigate the measurement, including loading method, electrode layout, electrical resistivity testing methods, signal collection and processing etc. the monitoring system of vehicle - speed, based on cfrc, is innovative obviously

    最後，提出了交通測速系統的工作原理，制定了實驗方案，製作實驗構件，進行了車速測量的模擬試驗。特別討論了加載方案、電極布置方案，電阻測試方法，信號採集和處理的方法等。
  14. Magnetic materials - methods of measurement of density, resistivity and stacking factor of electrical steel sheet and strip

    磁性材料.第13部分:電工鋼片和剛帶密度電阻率和疊層系數的測量方法
  15. Magnetic materials - part 13 : methods of measurement of density, resistivity and stacking factor of electrical steel sheet and strip

    磁性材料.第13部分:帶電的帶鋼和鋼板的密度電阻率和疊層系數的測量方法
  16. Standard test method for field measurement of soil resistivity using the wenner four - electrode method

    用溫納四電極法現場測量泥土電阻率的標準試驗方法
  17. Many important properties of semiconductor devices are relevant with their resistivity, which brings forward strict demands to the uniformity of the resistivity. especially micro - area ' s characteristics attract extensive attention. under this background, four - point probe measurement technique requires a new development

    許多器件的重要參數與電阻率有關，因此這對晶體電阻率的均勻性，電學特性提出了更為嚴格的要求，特別是微區的電特性和均勻性引起了人們的廣泛關注。
  18. Four - point probe measurement technique is one of the most extensive means for examining the resistivity in the semiconductor industry. with continuous progress, semiconductor industry develops at a very fast speed, the integration level of ic becomes higher and higher. presently, the ic production is entering into the age of ulsi, then testings are more and more important

    四探針測試技術是半導體工業檢測電阻率時採用最為廣泛的測試手段之一。隨著時代的不斷進步，半導體產業飛速發展，以單晶矽片為襯底的集成電路集成度越來越高，目前正進入甚大規模集成電路（ ulsi ）時代，測試在整個集成電路生產過程中的地位越來越重要。
  19. Metallic materials - resistivity measurement method

    金屬材料電阻系數測量方法
  20. On resistivity measurement of conductive sponge

    微波在靜電測試中的應用
分享友人
分享到 Line

分享到臉書