resul 中文意思是什麼

resul 解釋
雷蘇爾
  1. This article is based on the general rule of teachin g, and resul ts from six year ' s research in the civilian - run school. during the six y ears, i ' ve done much research work in many areas, such as the relationship between tea ching quality and students resourses, curriculum and teaching aims, texts and stud ents, overall attendence and individualized instruction, the reforming of tea ching and instruction of learrning, the effect of subject and object, the element of intelligence and non - intelligence, the knowledge instruction and the competen ce training, the knowledge in and out of the classroom, the classroom - teaching an d the after - class coach, etc. the purpose of what i have done is to seek for a ki nd of teaching principal which is fit for the rule of the economic market and mi ght be the best way for the education

    文章以教學的一般規律為據，結合作者在民辦學校的教學中進行的近六年的跟蹤調查和深入考察，就民辦學校的教學質量與生源市場、課程設置與培養目標、教材內容與學生實際、面向全體與因材施教、教法改革與學法指導、主導作用與主體作用、智力因素與非智力因素、知識傳授與能力訓練、課內知識與課外知識、課堂教學與課外輔導等十個方面的關系作了初步探討，尋找既合乎市場經濟規律，又符合教育規律的最佳結合點，以期為民辦學校總結行之有效的教學原則，提供可資鑒戒的參考。
  2. In the design of hardware, frequency sweep signal is based on dds + pll. by the control the singlechip c8051f060, ad9852, the dds chip, can achieve stepped frequency signal. with amplifying and detector circuits, the instrument can achieve the measurement and receiving of amplitude frequency characteristic result. by means of pdiusbd12 finish the usb1. 1 protocol conversion, communicate with usb interface of pc, the instrument give the measurement resul of amplitude - frequency characteristic in lcd of pc

    硬體方面，掃頻信號源基於dds + pll的技術，由c8051f060單片機控制dds晶元ad9852實現頻率步進。再加上外圍放大、檢波等電路，測量和接收幅頻特性。並藉助于pdiusbd12完成測量數據usb1 . 1協議轉換，實現與pc機的usb介面通信，將幅頻特性測量結果在pc機的液晶顯示屏上表達出來。
  3. In these paper we use the following rule to determine the width - to - thickness ratio : if the local buckling has visible effect on the overall buckling capacity, then this width - to thickness ratio should not be exceeded based on the resul ts obtained, we proposed a new formula for the limitation of the ratio of h / tw of the t - section columns " webs

    根據局部失穩對整體失穩不應該有顯著影響的原則，最後得到t形截面壓桿腹板的寬厚比限值計算公式。本文對規范修訂和工程應用有一定的參考作用。
  4. The resul showed that technology analysis was important for die designing and manufacturing

    表明了工藝分析對模具設計與製造的重要性。
  5. At the same time some regularity resul ts on minimisers of such free discontinuity problems have been obtained

    與此同時我們還得到解的若干正則性結果
  6. The resul ts indicated that there exists obvious gas gap in molten iron flowing front, and the pressure in gas gap with eps pattern during vacuum pouring is less than 1 a tm

    試驗結果表明，鑄鐵件流動前沿不僅存在明顯的氣隙，而且採用聚苯乙烯模樣材料，負壓下澆注時，其氣隙壓力低於1個大氣壓。
  7. Finally, we applied our optimal scheduling algorithm in the zircotube productive system of northwest zircotube co. ltd., which has a hybrid production system, and we achieved satisfactory resul ts

    最後，將優化調度演算法應用到屬于混合流程的錯管軋制生產系統中進行模擬，得到了滿意的結果。
  8. As a resul t, the electric construction companies must intensi fy the management and improve the ability, put more emphasis on the research and the management of the project contracts and especially on the claim for compensation to meet the need of the international market

    因此，我國電力施工企業必須加強管理、提升素質，加強對工程項目承包合同的研究與管理，尤其是要加強對施工索賠問題的研究，以適應將來市場化與國際化的需要。
  9. Effect of dehydration procedure beads of pavlova viridis were desiccated with four different procedures. two dehydration rates were used, which are 0. 9 % water content / h ( slow ) and 10 % water content / h ( rapid ). resul - ts showed that slow dehydration is the best. a dehydration combination of rapid dehydration to 70 % water content, followed by slow dehydration to the optimum water content is a better procedure. rapid dehydration is the worst

    （ 3 ）脫水程序的影響以綠色巴夫藻為研究對象，選擇0 . 9 %含水量/ h （慢）和10 %含水量/ h （快）兩種脫水速度，分兩步脫水，先脫水至70 %含水量再脫水至最佳含水量。結果慢-慢程序脫水，存活率最高；快-慢程序其次；快-快程序最低。
  10. 21a / w, and a1so get some other significative resul t. mair1 works and resu1t inc1ude : ( l ) by ana1yzing the the working pril1ci p1es of gan - - based msm ph ( ) to - detectors, we designed the two ki11ds of di fferent structure parameter of device. the electrode fingers are 2 p m wide, and l00 ll nl long, the gap.

    本文的主要工作和結果有： （ 1 ）通過對gan的msm結構探測器的工作原理的分析，我們設計了兩種尺寸的器件結構參數，確定了器件的金屬電極條寬為2 m ，長為100 m ，電極間距分別為6 m 、 10 m兩種，器件有效面積分別為104 m 155 m 、 150 m 155 m 。
分享友人
分享到 Line

分享到臉書