roller way 中文意思是什麼
roller way
解釋
輥道-
After designing oil ditches on the surface of its arc - block, increase friction factor and make sure self - lock which solves above problem. do qualitative analysis to lower pair and one - way overrunning clutch and inner star - wheel - roller overrunning clutch by using self - made lever loader. the experiment shows : on the same condition, the deformation of new overrunning clutch ’ s surface contact with lower pair is smaller than the deformation of roller overrunning clutch ’ s line contact with higher pair and new overrunning clutch ’ s skid angle is smaller
對低副單向超越離合器的部件進行了加工製造，在超越離合器弧塊表面創新設計加工排油溝，增大摩擦系數，保證實現自鎖，解決了很多離合器工作過程中容易出現無法自鎖的問題;對低副單向超越離合器和內星輪滾柱超越離合器用自製杠桿加載器做了定性分析，實驗表明:相同條件下，新型離合器低副面接觸比滾柱離合器高副線接觸變形小、溜滑角小。 -
When extracting the rollers from the kiln during working temperature, the rollers should be quickly rotated, the best way is put the roller in the special wheels moving shelf, keep it moving when the temperature is under 600 c, or warp the rollers with ceramic fiber to make it cool down
在高溫下抽棒時，應快捷並旋轉輥棒，最好放置在墊有耐火棉的專用旋轉支架上保持旋轉狀態直到溫度降到600度以下，或蓋上保溫棉使其緩慢冷卻。 -
Proceeding with the support " s force condition is analysed in the static and revolve state, the stress distributions in the contact areas of support and roller are researched by way of hertz theory, the tow - dimensional elastic movement of the contact area is studied by contact mechanics, and the formula and curve of movement regulation are deduced
從回轉窯靜止與運轉時支承的受力情況分析著手，依據赫茲接觸理論對托輪與滾圈接觸區的壓力分佈進行了分析，並用接觸力學方法研究了接觸區的二維彈性滑動，推導出回轉窯軸向下滑計算公式，從而得出回轉窯軸向下滑特性曲線。 -
Furthermore, it is easily arrived by air, by sea, by railway or by motor way. originated in 1990, our company specialises in producing concrete road construction equipment and small road roller equipment
年，是生產水泥混凝土路面施工設備及小型壓實設備的專業公司，擁有各種剪折沖車刨銑鋸磨床高頻焊等多種加工設備和冷噴熱熔劃線機。 -
Abstract : this article is based on the theory of fuzzy optimization design. the running speed and width and initialtensileforce and interval distance of roller are its design variable. the objective function is the minimum power loss of the traction motor. it constructs the fuzzy optimization mathematical model of the two - way running belt conveyer ' s main parameters
文摘:以模糊優化設計理論為基礎，以雙運帶式輸送機輸送帶的運行速度、寬度、初張力及托輥間距為設計變量；以牽引電機運行的最小功率消耗為目標函數，構造出了雙運帶式輸送機主參數的模糊優化數學模型。 -
Based on the theory of reliability design, combined with the conventional design code and the way of roller chain drive, the author discusses the reliability design of roller chain drive and provides some design examples
摘要根據可靠性設計理論，結合套筒滾子鏈傳動的傳統設計準則和方法，研討了套筒滾子鏈傳動的可靠性設計方法，並列舉了設計實例。 -
The paper designs a lower pair and one - way overrunning clutch. because its arc - block, outer ring, roller, slide - block and output shaft contact by lower pairs, they overcome higher pairs ’ shortcomings such as wearing easily, bad resistance to impact, bad bearing capacity and so on
本文創新設計了一種低副單向超越離合器，其弧塊與外環，弧塊與滾柱，滾柱與滑塊以及滑塊與輸出軸之間都是以低副聯接，克服了高副易磨損、耐沖擊性差，承載力低等缺點。 -
This machine has great feeding ability, easy to be regulated, can be fed with fixed quantity under control of time delay relay ; it is divided into one - way feeding and bidirectional feeding in terms of feeding direction, suspending type and seating type in terms of installation ; in order to assure precision of feeding, roller encapsulation is equipped to increase frictional coefficient between adhesive belt and rollers ; the rectangle discharging mouth has large dimension which can prevent humping up materials ; this machine has close structure, reliable application and can be easily repaired because it has many similar parts with belt type conveyor
該機給料能力大，調節給料量方便，又可在時間繼電器的控制下定量給料按給料方向該機可分為單項給料和雙向給料，按安裝方式又分為吊掛式和座式為了保證給料的精度，主動滾筒包膠，以增加膠帶與主動滾筒的摩擦系數料倉矩形卸料口的尺寸大，物料不易起拱該機結構緊湊，使用可靠，它與帶式輸送機有許多通用部件，故維修方便。 -
The cross short rollers guide way and servo feed - system are the most important parts of 3mz204cnc bearing internal grinding machine made by luoyany bearing research institute. - we have analysised firstly the factor of influence with roller guide way rigid, and we have obtained a load - distortion curve. we also have analysised the dominating factors influence with distinguish ratio of guide way, and we have obtained a solution about pre - tighted load which were tested by experiments
本文對洛陽軸承研究所研製的3mz204cnc全自動內圓磨床的核心部件：十字交叉滾子導軌和數控進給系統展開研究，首先對影響滾動導軌剛度的因素進行分析，得出載荷?變形曲線，對影響導軌解析度的各因素進行分析，得出預緊力大小與分佈對解析度和起動力的影響，並通過實驗驗證。 -
The structure is same as the one way clutch. it can precisely control the lower roller which will not reverse even for long time used as it is high in
1構造和單向裝置一樣，能相當精確地控制下輪，長時間使用亦不會使下輪有絲毫的倒退現象， -
Nanfang bearing co., ltd located in changzhou city jiangsu province, established on the basis of nanfang needle bearing factory, possessing two plants and four sales agencies in shanghai chongqing guangzhou zhejiang, is a specialized enterprise in producing various types of needle roller bearing and three type one way clutches
南方軸承有限公司座落在江蘇武進市高新技術開發區，在南方滾針軸承廠的基礎上組建而成，在牛塘鎮及上述開發區設有2家生產工廠，上海、重慶、江門、溫嶺設有辦事處，專業生產各類滾針軸承及超越離合器。 -
Simultaneously, the quality control method for the compaction, the construction technologies and measures and the roller - compacted parameters are studied and optimized, in this way the investment is saved at last
同時，制訂了壓實質量控制方法，研究和改進了填築的施工工藝和措施，優化了大壩體型及施工碾壓參數，節約了投資。 -
In this way, the new - type measurement, different from the traditional roller method, can carry out measuring the figure errors and can determine the diametet, the perimeter and the figure errore at one time besides, the paper also brings forward the detailed data processing method
使一次測量就可以同時測出工件的周長直徑和形狀誤差，解決傳統滾輪法無法測量工件形狀誤差的問題，同時還提出具體的數據處理方法。
分享友人