rotation controller 中文意思是什麼

rotation controller 解釋
旋轉控制器
  • rotation : n. 1. 旋轉；輪轉；循環。2. 【天文學】自轉。3. 【物理學】旋度。4. 輪流，輪換；交替。5. 【農業】輪作；【林業】輪伐（期）。
  • controller : n 1 管理人，主管人。2 （會計的）主計人，檢查員；〈英國〉（特指宮廷、海軍等的）出納官〈常作 comptr...
  1. Equipped with electronic controller fini tronic and preset for remote control for two or more compressors. it offers working pressure and oil mist separator tank inner pressure indication, separator filter clogging lashing alarm before overpressure e - stop, electric motor temperature control, maximum screw assembly temperature control, air temperature on pressure end indication, electric motor direction of rotation check, time to scheduled maintenance term, total operating hours and operating hours under load, alarm log of last five failure events

    並預設為丙臺以上空壓機聯機遠程控制，有工作壓力和油氣分離器罐內壓指示，分離器過濾器阻塞報警，電機溫控，螺桿總成溫控，壓力端空氣溫度指示，電機轉向檢查，維護周期油，油過濾器，空氣過濾器，分離器過濾器，總運行時間和負載運行時間，記錄上五個報警故障等。
  2. Because the controller is easy to get the position of rotor by the encoder, we can continuously rotate the flux of the armature rotor by applying spwm method to the control system. the continuous rotation of the flux of armature make the output torque of motor has no ripple

    由於通過編碼盤可以輕易獲得精確的電機轉子位置信號，故運用spwm調制方法可以使得無刷機的電樞磁場按照圓形軌道連續旋轉，從而實現輸出轉距無脈動。
  3. The rotation control technology in the laser gyro strapdown inertial navigation system was studied. the method of realizing closed - loop digital control with rlg located in the strapdown inertial navigation system was discussed. the structure of rotation servo system was introduced. the designing method and process of the digital controller were given. the method of implementing digital controllers by means of computer and software flow were demonstrated. the result of simulation and debugging of this system showed that it fullfills the requirment of the strapdown inertial navigation system. it assures the stability of rotation and solves the problem of striking without increasing the volume and cost of the system

    研究激光捷聯慣導系統中的轉位控制技術.採用捷聯慣導系統本身的rlg實現轉位系統的閉環數字控制，給出了轉位伺服系統的結構組成以及數字控制器的設計方法和設計過程，給出了數字控制器的計算機實現方法和軟體流程.模擬及調試結果表明，所設計的轉位伺服系統滿足捷聯慣導系統的要求，既保證了轉動的平穩性，克服了到位撞擊問題，又不增大體積、增加成本
  4. In this paper, the design of electric forklift driving controller is demonstrated. otherwise, can is added into this controller, so as to build up can networks with other modules equipped with can controllers. this paper is composed of 7 chapters : in the first chapter, the background of the paper is introduced ; in the second chapter, the structure of electric forklift is demonstrated ; in the third chapter, first the math model of series motor is found, then the motor is controlled as improved p1d control rule ; in the fourth chapter, the principle and realization method of forward and reverse rotation and back - feed brake are explained ; in the fifth chapter, the principle of can and design of application layer in can are illuminated ; in the sixth chapter, the principle of e2prom is clarified ; in the last chapter, summary of the whole paper is given, and prospect in this field is made

    全文共分七章：第一章緒論，介紹了論文背景；第二章，系統綜述，介紹了電動叉車的整車結構；第三章，串勵電機的建模、改進的pid演算法及其軟硬體實現，首先根據串勵電機的機電特性推導出數學模型，然後在此基礎上結合pid控制規律對電機進行控制；第四章，串勵電機的正反轉及回饋制動，介紹了實現電機正反轉及回饋制動的原理及方法；第五章， can網路實現模塊間通訊，介紹了can總線原理及can總線應用層設計；第六章，用串列e ~ 2prom實現參數設定，介紹了串列e ~ 2prom的原理；結束語，對本論文進行了總結，並對該領域的發展進行了展望。
  5. In the part of the experimental designs, a experimental configuration of an unstable cavity by use of two bbo crystals compensating the walkoff effect and pumped by reflection is presented, and two set of controlling systems designs of open and closed loop are also presented ; we realized closed loop controlling system of bbo optical parametric oscillator tuning system, by using american general scanning inc. ' s controller to control bbo crystal ' s rotation, and scaled the output wavelength with charge coupled device

    在實驗設計上給出了利用兩塊bbo晶體補償走離效應返回式泵浦非穩腔的實驗設計，設計了開環和閉環兩套控制系統。通過使用美國通用掃描公司的掃描頭控制bbo晶體的轉動，用ccd對bbo - opo輸出波長進行標定，實現了bbo - opo調諧系統的閉環控制，相對波長調諧誤差小於0 . 04 ，並給出了354 . 7nm泵浦的類相位匹配bbo - opo輸出波長隨晶體轉角變化的理論和實驗曲線。
  6. Depending on the optimized model of thermal torpedo ' s power & propelling system, the method of rotation rate close - circuit control is used in rotation rate controller, which is based on variable structure control for nonlinear systems. finally, the rotation rate controller is designed and passed through the debugging

    針對魚雷熱動力推進系統的非線性特點，研發出基於非線性變結構控制的轉速控制規律，並成功研製了動力推進系統控制系統的核心部件? ?轉速控制器。經模擬和調試驗證，所搭建的測控系統結構合理、性能完備；轉速控制器滿足使用要求。
分享友人
分享到 Line

分享到臉書