round die 中文意思是什麼
round die
解釋
圓板牙-
Nana described her own great happiness. her baby, the little louis, she said, was now at the house of her aunt, who brought him round to her every morning at eleven o clock, when she would take him into her bed, where he played with her griffon dog lulu. it was enough to make one die of laughing to see them both burying themselves under the clothes at the bottom of the bed
娜娜說孩子是她的最大快樂：他的寶貝小路易現在放在她的姑媽家裡，每天上午快到十一點鐘時，姑媽就把他帶來，她把他抱到床上，讓他在上面與她的捲毛狗呂呂一起玩，看見他們兩個鉆在被窩里的樣子，簡直笑死人了。 -
( 6 ) in this paper. adopting fea software ansys to simulation and analysis the al ecap process. in order to spread out studying of ecap in the future. the results show : die comer angle, the radius of round angle, the friction coffience of workpiece and die, the properties of die ( elastic modulus, possion ratio ) et al, have some degree impact on the deformation of materials
（ 6 ）採用有限元（ fea ）分析軟體ansys對al的擠壓過程進行ecap模擬與分析，為后續研究工作做好鋪墊，分析結果表明：外切角、圓角半徑、試樣與凹模之間的摩擦系數、凹模本身的特性（如彈性模量、泊松比等）等等，對材料的變形量都由不同程度的影響。 -
Plates of fine blanking die. round backing plates
精沖模模板.圓形墊板 -
The springback angle increases with the increase of the punch round radius and clearances between the punch and the die while decreases with increase of the blank holder force, sheet thickness, friction coefficient and material hardening exponent
回彈角隨凸模圓角半徑和凸凹模間隙的增大而增大，隨壓邊力、板料厚度、摩擦系數和材料硬化指數的增大而減小。 -
Die - casting die components - part 2 : round insert block
壓鑄模零件第2部分:圓形鑲塊 -
Hard alloy die is made y taking high - quality hard alloy as its nips and fastening with steel die case. it is characterized by high hardness, good thermal conductivity, brasive coefficient and strong resistant to corrosion. it is suitable for drawn metal wire, bar and pipes. the types of dies includes rectangle, hecagon, octagon, diamond, trapezoid, basin and knob, u - shaped and half round types
硬質合金模具採用優質合金作模芯，並用鋼質模套緊固，具有硬度高，導熱性能好，磨擦系數小，抗腐蝕性等特點，適用於拉制金屬線材，棒材，管材等，另外，模具的類型有矩型、六角型、八角型、菱型、梯型、凹型凸型、馬蹄型、半圓型等各種異形模。 -
I feel certain you will die in your bed when you're a hundred and two, with a crowd of descendants weeping round you.
我拿準了你會以102歲的高齡死在床上，有成群的兒孫聚在你身邊。 -
We all have to die in the end, and a sudden smoking - related heart attack is a cheap way to go compared with 30 years of state pension or round - the - clock nursing care for someone with alzheimer ' s disease
我們最終都會死，與支付30年國家養老金或者對一位患有老年癡呆癥的人進行24小時護理相比，由吸煙導致心臟病猝死是一種廉價的死亡方式。 -
A third part of thee shall die with the pestilence, and with famine shall they be consumed in the midst of thee : and a third part shall fall by the sword round about thee and i will scatter a third part into all the winds, and i will draw out a sword after them
結5 : 12你的民三分之一、必遭瘟疫而死、在你中間必因饑荒消滅三分之一、必在你四圍倒在刀下我必將三分之一分散四方、方原文作風並要拔刀追趕他們。 -
Plates of fine blanking die. round retaining plates
精沖模模板.圓形固定板 -
Abstract : this paper analyses the drawing technology of canopy, gives outthe gradual forming methods for inner ? concave round part, designs rational die structure, and introduces work principle of the die, the design and parameters of the main parts
文摘:分析了燈座的拉深工藝，提出了凹形球環部分的逐段成形方法，設計了合理的模具結構，介紹了模具的工作原理、主要工作零件的設計和參數。 -
Edward cole : we live, we die, and the wheels on the bus go round and round
愛德華?科爾：我們活著，我們死了，就好像公車上的輪子一樣，一圈一圈地旋轉前進。 -
Die throat radial stress was analyzed during every phase of drawing when the round draw bead be used, the formula of even stress intension in every region are deduced, this work establish the theory base of software programming about drawing the curved surface part
摘要以半圓筋為例，分析得到了使用拉深筋拉深曲面零件時，拉深各階段凹模入口的徑向應力公式，並且對拉深各位置段的平均應力強度進行了求解，為開發曲面零件拉深應用軟體奠定了理論基礎。 -
I think i would die ! as it is, i ' m already so shy in front of a camera. i would probably get kicked out in the second round
我想我會死!現在來說?在鏡頭前我已經很害羞。我想我會在第二圈就被淘汰。 -
Then the screen round her bed for her to die
然後周圍屏遮起她的床，等著她咽氣。
分享友人