screw hole 中文意思是什麼

screw hole 解釋
螺釘孔
  • screw : n 1 螺旋；螺釘。2 螺旋槳；暗輪。3 暗輪輪船。4 螺旋狀物。5 拔塞器；螺絲鉆子。6 螺旋的一擰；螺旋的...
  • hole : n 1 洞，穴，孔；（衣服等上的）破洞；傷口；漏洞；窩，坑；水流的深凹處，（河道的）緩流窪。2 （獸的...
  1. This article offers a method for solving the frictional drag, that is, according to the various buckled shapes of coiled tubing in different hole sections, working out the mean contact counterforce in a screw pitch in solving the radial contact counterforce

    求解摩阻力時，可針對連續油管在井身中不同結構段的不同變形形狀，採用求解徑向接觸反力時求一個螺距內平均接觸反力的方法加以解決。
  2. Compared with the mud on wall form hole technology, clash stake technology or vibration sink pipe technology used in complex foundation stake forming, it has advantages of no vibration, no pollution, and no noise. in addition, since the concrete pressed into the drill stem sent vibration free concrete to the pump, so it is eas y to ensure the quality of the stake body. compared with the mud on wall and dry work form hole technology, the side obstruction and end obstruction of screw drill press concrete stake have all been accordingly improved, the weight bearing is better, and the transmutation of the complex foundation is less

    其中，螺旋鉆孔壓灌混凝土成樁技術自研製以來，已在多項復合地基工程中進行了應用，較好地解決了軟弱地層成孔困難的問題，適應地質條件范圍廣，成樁速度較快，工期短、工效高；與復合地基成樁時的泥漿護壁成孔工藝、振沖樁工藝或振動沉管工藝施工比較，具有無振動、無污染、無噪音的優點；另外，壓入鉆桿內的混凝土為泵送免振混凝土，因此樁體質量易於保證；與泥漿護壁和干作業成孔工藝相比，螺旋鉆孔壓灌混凝土成樁的側阻和端阻都有相應的提高，樁的承載性能較好，復合地基的變形較小。
  3. The main popular theoretical method adopted to study end - plate connection is finite element technique under monotonic loading at present. this paper applies nonlinear ( material, geometry and contact ) finite element method to analyze the behaviors of connections under cyclic load at fist time. contact elements are set between end plate and column flange, screw cap and neighborhood plane, bolt bar and hole

    對于端板連接的理論分析，目前國內外的研究主要局限在單向加載有限元分析范疇，本文首次採用三維非線性（包括材料、幾何與狀態非線性）有限元對端板連接進行了循環加載分析，端板與柱翼緣間、螺栓頭（帽）與相鄰板件間、螺栓桿與孔壁間都設置了反映邊界狀態的接觸單元。
  4. Through - hole machine and hand taps of internal screw on light alloy for installing wire thread insert

    輕合金安裝鋼絲螺套用內螺紋通孔的機手用絲錐
  5. Pistol drilling, 6 - 8mm glass hole - maker, 6 - 8mm glue grain, level ruler or level pipe mainly for installation of suspended door, 68 expansion bolt, cross and subtraction sign screw driver etc

    手槍鉆6至8mm玻璃開孔器6至8mm膠粒水平尺或者平水管主要用在吊趟門安裝6x8膨脹螺絲十字批和一字批
  6. Sheet metal rim holes with screw thread ; prepunch hole diameters

    帶螺紋的金屬薄板凸緣孔.預沖孔直徑
  7. Hexagon head screw plugs - with retaining pin and bleeding hole

    帶臺階和外六角鎖緊螺釘.鎖緊頭和排放孔
  8. Insert special bolt into the preset hole of c form parts, where the bolt will be fixed into the threaded hole of wedge, then screw the bolt on with a socket spanner until the first nut drops

    將專用螺栓插入c形無件預留孔與楔塊的螺紋孔相連，用套筒扳手擰緊螺栓直到第一個螺帽自行斷落。
  9. The ascend and descend of work bench by screw pole and it can control the rough adjust effectively, and micro - adjust by screw cap of power head, the center hole of bench are coaxial with the spindle, and it put the holder available, and added the aerosol lubricate system in the air current it has the function of filter

    該機應用有國際先進的徑向鉚接技術外，同時採用絲桿升降式工作臺機頭部分固定，臺面具有夾具梯形槽，工作臺中心孔徑與主軸軸線同軸，可用於夾具定位。電控部分加裝數顯時間繼電器，數顯計數器，方便操控。
  10. This machine is a kind of radial riveting machine, the machine adopted the advanced radial technology, and its movement path likes the 11 pieces of plum blossom s shape, and using the screw pole to ascend and descend the work bench the head part is fixed, and the t - slot of bench can fix the clamping apparatus available, the center hole of bench and axis are coaxial, the one - way adjusting valve of liquid current is effectively controlled riveting speed

    Jm12 - c是液壓類中重型徑向鉚接機，除應用有第五代徑向鉚接技術外，該機加長了鉚接行程，該項參數由普通機型的30mm加至60mm ，可滿足長行程深孔內鉚釘鉚接的要求。工作臺，並具有夾具梯形槽，工作臺中心孔徑與主軸軸線同軸，可用於夾具定位。氣路加裝雙向調節閥，有效控制鉚接速度。
  11. This special heat - treatment ensures full bearing performance and prevents the set screws from loosening during operation as the set screws can be tightened hard enough without causing broken inner ring set screw hole

    內圈螺釘孔周圍經局部高溫回火后，軸承獲得更好的性能，可防止螺釘在軸承工作期間松脫，同時螺釘擰得緊也不會導致內圈爆裂。
  12. Thereby the simulation of machining screw and hole has been perfected

    進一步完善車削中螺紋加工、孔加工和圓弧曲面加工的模擬。
  13. According to the theory of developing viscous crude with screw pump and combined with the reservoir characteristic and oil property, fault block 70 is developed reasonably and effectively through a series of corollary technique including chemical pre - processing in the formation, viscosity decrease in the well bore, down - hole anchoring of screw pump, optimized design of screw pump, reasonable determination of the turning rate of screw pump, frequency alternating control, heat exchange and viscosity decrease in well head, monitoring of screw pump

    依據螺桿泵開采重油的理論，結合澤70斷塊稠油油藏的特點和原油物性，通過實施地層化學預處理、井筒降粘、螺桿泵井下錨定、螺桿泵優化設計、螺桿泵合理轉速的確定、變頻控制、井口換熱降粘、螺桿泵監測等一系列螺桿泵配套工藝技術，使澤70斷塊得以合理有效的開發。
  14. Through - hole machine and hand taps of internal screw on common stees for installing wire thread insert

    普通鋼安裝鋼絲螺套用內螺紋通孔的機手用絲錐
  15. Non through - hole machine and hand taps of internal screw on common stees for installing wire thread insert

    普通鋼安裝鋼絲螺套用內螺紋不通孔的機手用絲錐
  16. Bm12 t is a kind of medium sized orbital riveting machine and driving by hydraulic. its adopted the advanced orbital technology, process by cold rolling. the ascend and descend of power by screw pole and it can control the rough adjust effectively, and micro - adjust by screw cap of power head, the center hole of bench are coaxial with the spindle, and it put the holder available

    Bm12t是液壓類中型徑向鉚接機，該機應用有第五代擺輾鉚接技術外，同時採用絲桿升降式動力頭機頭部分不固定，臺面具有夾具梯形槽，工作臺中心孔徑與主軸軸線同軸，可用於夾具定位。
  17. As shown in the figure left, the inner ring of the self - contained bearing is hardened in the race - way and surroundings part where hardening is necessary, the area of set screw hole of the inner ring has been templed by high temperature after hardened, it has higher toughness and impact clasticity

    如左圖所示，內圈溝道及其周圍需要淬硬的部分已經過正常淬火，裝配緊定鏍釘的內圈伸長端則經過高溫局部回火而保持韌性及抗沖擊性。
  18. Measurement of screw thread hole position

    螺紋孔系位置度的測量
  19. Its adopted the advanced radial technology, the motion path of riveting - head resembles 11 pieces plum blossom s shapes. the ascend and descend of power by screw pole and it can control the rough adjust effectively, and micro - adjust by screw cap of power head, the center hole of bench are coaxial with the spindle, and it put the holder available

    Jm9t是液壓類中型徑向鉚接機，除應用有國際先進的11瓣梅花徑向鉚接技術外，該機加大了工作臺面，並具有夾具梯形槽，工作臺中心孔徑與主軸軸線同軸，可用於夾具定位。
  20. Jm6tq is developed in foundation of jm6t, its adopted the advanced radial technology, the motion path of riveting - head resembles 11 pieces plum blossom s shapes. the ascend and descend of power head by screw pole and it can control the rough adjust effectively, and micro - adjust by screw cap of power head, the center hole of bench are coaxial with the spindle, and it put the holder available, and added the aerosol lubricate system in the air current it has the function of filter

    Jm6tq氣動是在jm6t基礎上發展而來的氣動z中小型徑向臺式鉚接機，除應用有國際先進的11瓣梅花徑向鉚接技術外，該機應用有國際先進的徑向鉚接技術外，同時採用絲桿升降式工作頭，臺面具有夾具梯形槽，工作臺中心孔徑與主軸軸線同軸，可用於夾具定位。
分享友人
分享到 Line

分享到臉書