scuffing 中文意思是什麼

scuffing 解釋
紙張起毛
  1. The maximum load on a bearing should always be smaller than the relief load in order to avoid scuffing.

    為了避免劃傷，軸承上的最大負荷應該總是小於其卸載負荷。
  2. Standard test method for scuffing load capacity of gears

    齒輪膠合承載能力試驗方法
  3. The loca | n320gear oil used in gearbox of coal mill, the gears appeared pitting and scuffing, meanwhile shocking and noise increased, the oil oxidized and sludge formed

    磨煤機齒輪箱使用n320齒輪油，造成齒輪點蝕，齒面嚴重磨損，振動及噪音增大，油質氧化，產生油泥。
  4. Scuffing failure of piston ring - cylinder liner in liquid - solid lubrication

    自潤滑軸承在煉鐵廠托輥中應用的試驗研究
  5. The development of scuffing-type damage is illustrated in fig. 1. 11.

    膠合形式損壞的發展情況示于圖111中。
  6. This paper mainly discussed the optimization design of two - stage star - type gear transmission system. it covered the two sides : one - stage gear transmission and two - stage gear transmission. on the basis of their analysis and research, the mathematic models are created which include the objective functions of minimum volume and minimum center distance, the constraints of contact strength, bend strength and scuffing strength

    本文主要研究了航空發動機星型齒輪傳動系統的優化設計，對單級齒輪傳動和兩級星型傳動都進行了深入的分析和探討，分別以系統體積最小和中心距最小為目標函數，以齒輪的接觸強度、彎曲強度、膠合強度等為約束條件，建立了完整的數學模型。
  7. Slbocle test method for evaluating lubricity of diesel fuels by the scuffing load ball - on - cylinder lubricity evaluator slbocle

    通過磨損負載下氣缸上球潤滑性鑒定器
  8. Standard test method for evaluating lubricity of diesel fuels by the scuffing load ball - on - cylinder lubricity evaluator slbocle

    通過磨損負載下氣缸上球潤滑性鑒定器評價柴油燃料潤滑性的標準試驗方法
  9. Standard test method for evaluating the scuffing load capacity of oils fzg visual method

    評定油磨損荷載能力的標準試驗方法
  10. For the first time, it puts forward a conception of. thermal dynamic simulation and sets up a supposed analytical theory for scuffing failure and cylinder scoring of piston assembly and cylinder liner. that is followed with the simulation of scuffing failure and cylinder scoring of internal combustion engine under the condition of stopping cooling water supply and over loading

    首次提出了熱動態模擬的概念，第一次大膽假設了活塞組、缸套擦傷、拉缸時的分析理論，模擬出了在中斷冷卻水和超負荷狀態下柴油機的擦傷、拉缸。
  11. Mechanism analysis and betterment measure on scuffing of hydraulic pressure equipment

    液壓升降裝置拉缸機理分析和改進措施
  12. The signal processing software was developed by vc + + tools. the modules of the software including board controlling, signal input, data saving, figure display, statistic computing, filter design, spectrum analysis, etc. based on the experiment performed on the piston ring - cylinder bore wear tester, the friction force and max scuffing load under different liquid - solid lubrication ( the solid concentrations are 0 %, 0. 02 % and 0. 1 % by weight, the type of particles are mos2 and udp ) is investigated in this thesis

    然後，以內燃機中的活塞環-缸套摩擦副為目標，在活塞環-缸套摩擦副實驗臺架上進行模擬實驗，考察在不同二相流潤滑（潤滑油分別為純潤滑油、含納米級金剛石粉（ udp ） 、二硫化鉬粉（ mos _ 2 ）的濃度為0 . 02和0 . 1的液-固二相潤滑油）條件下摩擦副的摩擦力及極限擦傷載荷的變化。
  13. The method can meet fully the need of the evaluation of the scuffing load capacity to all kinds of worm gear oil. the different kind of additives and varied contents of additive have obvious influence on the scuffing load capacity of worm gear oil. for mixing worm gear oil, the additives that suitable for worm gear oil should be made of anti - wear additive which is the mainly component and a little extreme pressure additive which has a gentle performance

    試驗研究結果表明：本文研究開發的蝸輪蝸桿油膠合承載能力臺架評定方法具有較好的重復性和區分性，能夠滿足評定各種蝸輪蝸桿油膠合承載能力的需要；添加劑的不同類型及不同復配形式對蝸輪油的膠合承載能力有著較明顯的影響；在調制蝸輪蝸桿油時，適用於蝸輪蝸桿油的添加刑，應以油性劑為主劑，復加少量的性能較溫和的極壓抗磨劑。
  14. Based on the tribology theory, the experiment method of the scuffing load capacity of worm gear oil was studied in this paper by means of the large number of groping evaluation experiments, and based on the test results of worm gear drive lubricated by 15 types oils and the surface analysis of worm gear after the experiments, the effect of oils and additives on anti - scuffing load capacity of worm gear pair was studied. the results show that the experimental method of the scuffing load capacity of worm gear oil has a good repeatability and distinguishability

    本文運用摩擦學理論，通過進行大量的臺架評定探索性試驗，研究開發出蝸輪蝸桿油膠合承載能力臺架評定試驗方法，並在此基礎上進行15種不同配方的蝸輪蝸桿油的膠合承載能力臺架評定試驗和試驗后蝸輪齒面的表面能譜分析，以考察潤滑油、添加劑對蝸桿傳動膠合承載能力的影響結果。
  15. Testing coated fabrics - method 34 - method for determination of resistance to scuffing and snagging

    塗覆織物試驗方法.第31部分:方法34 :耐劃痕性和粗擦損性測定方法
  16. Calculation of scuffing load capacity of cylindrical, bevel and hypoid gears - part 1 : flash temperature method

    圓柱齒輪錐齒輪和準雙曲面齒輪膠合承載能力計算方法第1部分:閃溫法
  17. Calculation of scuffing load capacity of cylindrical, bevel and hypoid gears - part 2 : integral temperature method

    圓柱齒輪錐齒輪和準雙曲面齒輪膠合承載能力計算方法第2部分:積分溫度法
  18. Especially the work for evaluating the scuffing load capacity of worm gear oil is just been carrying out abroad but not at home

    尤其是在蝸輪蝸桿油膠合承載能力試驗研究方面，國外才剛剛起步，國內還是空白。
  19. Gears - fzg test procedures - fzg test method a 2, 8 50 for relative scuffing load - carrying capacity and wear characteristics of semifluid gear greases

    齒輪. fzg試驗規程.有關半流質齒輪潤滑油的刮磨承載能力和磨損特性的fzg試驗方法a 2 8 50
  20. Calculation of load capacity of bevel gears without pinion offset ; calculation of scuffing load capacity

    非偏軸傘齒輪承載能力計算.第4部分:磨損載荷計算
分享友人
分享到 Line

分享到臉書