section curve 中文意思是什麼
section curve
解釋
截面曲線-
Fluid noise mainly comes from out put pulsation of rate of flow, the main reason of out put pulsation of rate of flow is the instant high pressure return flow that obturation cubage produced when the big round curve pressure transition. the v trough on the port plate can reduce the fluid noise. in this paper, the author based on the acting of dam a river and condensability of liquid and used matlab language as tool to calculate the v trough on the original port plate and drew out the p - t diagrammatic curve and analyzed its shortcoming and improved the design of original v trough and got that the best size of its angle was 12. 3 and its length was 5mm and the cross section was an equilateral triangle
流體噪聲主要來源於輸出流量脈動，造成輸出流量脈動的主要原因是閉死容積在大圓弧段壓力切換時產生的瞬時高壓迴流，在配流盤上開設v型尖槽可降低因高壓迴流而引起的流體噪聲，本文以截流作用和液體的可壓縮性為理論依據，以matlab語言為工具，對原配流盤上的v型尖槽進行了理論計算，繪制出p - t圖線，分析了它的不足，並對原有v型尖槽進行了優化設計，得出了v型尖槽的最佳幾何尺寸：配流盤平面上的v型尖槽的兩邊的夾角為12 . 3 ，槽長5mm ，槽的橫截面為等邊三角形。 -
Further more, this algorithm also provides the criterion distinguishing edge inflexion and sleek curve section and the method computing inaccurately curvature radius and approximate perimeter. the paper also introduces the use method with cell edge hollow repairing and overlap or conglutination cell segmentation. for example, this algorithm has proved high - speed and has a good effect of cell segmentation on more than twenty groups of conglutinate and absent cells which are gathered from three kinds of cells
同時給出了利用這些參數判別邊界角點，邊界光滑段的判據，以及估算曲率半徑，等效周長的方法;最後，以細胞邊界凹陷的修補和重疊細胞粘連的分割為例驗證了演算法的可行性，該演算法在採集到的30餘組粘連和缺損細胞上進行了驗證，結果表明，該演算法處理速度快，分割效果良好。 -
Firstly, simulate flow field of rear smoke channel, plot velocity magnitude and ash concentration distribution in section of entry of heat pipe air preheater, compare with data which were measured in guiyang power station, verify simulation to be reasonable and right. secondly, simulate all kinds of factors which affect flow field ' s uniformity such as length, thickness, location of diffluent board, ash concentration, ash diameter, and so on, find the chiefly factors. thirdly, install guide board in curve channel in rear smoke channel, then simulate its " flow field, plot velocity magnitude and ash concentration distribution
在此基礎上模擬在冬夏兩季不同情況下，不同流速對熱管空氣預熱器壁面溫度的影響；然後對影響整個流場分佈的各種因素：包括分流板長度、厚度、偏離中心流道位置的偏離度、飛灰濃度、飛灰粒徑等因素進行數值模擬；最後提出在分流煙道轉彎處加裝導流板，並模擬加裝導流板后的流場分佈，得到下級空氣預熱器出口、熱管空氣預熱器進口處的斷面速度場分佈、濃度場分佈，以論證加裝導流板能達到流場均勻化的作用。 -
Firstly, the status of our nation ' s water resources, flood and arid hazards is overviewed to illustrate the necessity for study on dynamic control of flood season limited water level. disadvantages in traditional limitsd water level design, static control of limited water level design, static control of limited water level and fuzzy limited water level curve are pointed out, and mending methods for these are introduced. dynamic control and its key problems are analyzed hi next section. the allowable range of limited water level is determined, so as the allowable extreme risk index. the definition of extreme risk is re - illustrated, risk analysis methods in reservoir operation is discussed either. according to the definition of extreme risk rate, the allowable extreme risk rate of reservoir is systematically demonstrated with variant extreme risk indexes and flood season limited water level
本文首先闡述了我國水資源狀況和水旱災害、說明水庫汛期限制水位動態控制研究的必要性；介紹了傳統汛限水位設計、汛限水位靜態控制、模糊汛限水位過程線存在的問題及其初步改進方法；分析汛期限制水位動態控制的方法及關鍵問題；進一步闡述了水庫極限風險率的定義；根據極限風險率定義，詳細敘述了不同極限風險指標時、不同汛期限制水位下起調，水庫所能承受的極限風險率計算方法。然後，基於極限風險率計算方法，以白石水庫為背景，研究「考慮壩體自身安全、考慮壩體安全與下游防護對象控制下泄流量的汛限水位動態控制的極限風險率」 。 -
Curve of area of midship section
船體中段剖面面積曲線 -
The equations of workspace boundary surfaces for double - octahedron variable geometry truss pmts are derived based on surface analysis method. the projection and section curve grapha of workspace boundary surfaces for double - octahe
推導出了zrps ztps型及m 3tps型並聯機床運動學分析的一階和二階影響系數矩陣，得到了其運動學模型。 -
The article is directed by the modern structural geology, seismic stratigraphy and petroleum geology. in the study of works, geology, seismic and logging data are used. with the computer ' s ( workstation ) help, adopted many methods which are the technology of balanced section, calculation of the structural movement rate, the renewal of the erosion thickness, renewal of the ancient thickness, the protraction of the cover history curve and the " pagoda " figure, and based on the previous research achievement, this article studies the characteristic of rupture and fold, the degree of structural movement and the fashion of structural movement and brings forward that ludong area has experienced three big phases of structural evolvement
以現代構造地質學、地震地層學和石油地質學為指導，全面利用各種地質、物探、測井資料，藉助先進的計算機（工作站） ，採用多種方法（平衡剖面技術、構造活動速率計算、剝蝕厚度恢復、古厚度恢復、埋藏史曲線製作、寶塔圖製作等） ，並結合前人的研究成果，研究了陸東地區斷裂和褶皺的特徵、構造運動的期次以及構造運動的方式，提出了陸東地區經歷了三個大的構造演化階段。 -
The section plane display algorithm is studied in the thesis, and the interaction section and curve section display is achieved, which can provide the aids for observation and analysis of organs. also, it is very helpful for the dose distribution analysis
本文研究了顯示任意剖面的演算法原理，並實現了互動式的任意剖面顯示和曲線剖面顯示，這不僅能為器官的觀察、分析提供幫助，同時能為在組織器官受到射線照射后定量、定位地分析劑量分佈提供很好的手段。 -
In this paper, the finite - element numerical analysis calculation is applied to the foundation of high - rise and multi - floor building and the evolvement law of stress and displacement of tunnel used by urban traffic to explore the mutual influence between the wall rock of underground space and high - rise building foundation, taking account of the specific construction situation in the " sanmu garden " project in dadukou district in chongqing, from the perspective of underground space static - force structure stability analysis to open a underground tunnel with 6m in span and 7. 5m in height for track traffic 20m below the surface. this paper, taking considerations of three different states, i. e. the natural state without any artificial interference, the state of high - rise buildings on the surface, and the underground tunnel state with excavation for track traffic, and four plane lines and four vertical lines, analyzes and studies the distributing law of stress and displacement of calculation section from the following aspects : ( 1 ) the main stress vectorgraph, displacement distribution graph ( ux, uy ) and chromatogram graph of stress isoline ( 1, 2, xy ) of section under different states ; ( 2 ) the contrastive distribution curve of stress ( 1, 2, xy ) of different plane and vertical lines under the same state ; ( 3 ) the contrastive distribution curve of stress ( 1, 2, xy ) of the same plane and vertical lines under different states, wishing to provide references for underground space utilization and project designing and construction of the tunnel under high - rise buildings in the future
本文結合重慶市大渡口區「三木花園」開發建設項目，從地下空間靜力結構穩定性分析角度出發，針對在該項目中涉及的高層和多層建築物以及在其地下20米處開挖了一個用於軌道交通的跨度6米，高7 . 5米的地下隧道這一具體工程情況，採用2d - 3d -有限元結構分析程序對高層與多層建築物的地基基礎及其與城市軌道交通使用的地下隧道圍巖的應力與位移演變規律進行了有限元數值分析計算，探索了地下空間圍巖與高層或多層建築物地基基礎之間的相互影響，通過考慮未受到任何人為擾動影響的天然狀態、地表存在多層或高層建築物狀態和地下開挖用於軌道交通的地下隧道狀態等三種不同狀態以及4個水平剖線和4個垂直剖線等不同情況，從以下幾個方面具體分析研究了計算斷面的應力與位移分佈規律： （ 1 ）在各種不同狀態下計算斷面的主應力矢量圖、位移分布圖（ ux 、 uy ）以及應力等值線色譜圖（ _ 1 、 _ 2 、 _ （ xy ） ）等； （ 2 ）相同狀態下不同水平與垂直剖線的應力_ 1 、 _ 2和_ （ xy ）對比分佈曲線； （ 3 ）不同狀態下相同水平或垂直剖線的應力_ 1 、 _ 2和_ （ xy ）的對比分佈曲線等，為今後在對地下空間的開發利用以及在高層建築物地下開挖硐室時的工程設計和工程施工提供參考依據。 -
It is determined that with accurate knowledge of the complete stress - strain curve of concrete in compression, steel in tension, and with an iterative computerized non ? linear method, it is possible to predict the entire moment - curvature, moment - flexural rigidity and axial rigidity relation ship of a cross - section of a structure member
可以確定，只要知道混凝土受壓和鋼筋受拉的完整的應力應變關系，採用選代的非線性計算方法，就有可能預測結構截面彎矩一曲率、彎矩一彎曲剛度和軸向剛度的關系。 -
By this solution, a balde body model can be created by the optimization of the parametric grid of the blade body surface. some key techniques used in the solution, such as the computation of the data points on the meanline, the technology of cotinuty between the leading line and the outline of the blade body and the technology of the cross - section curve discretization, are disserated, and corresponding algorithm are presented in this paper
在進行參數網格優化的過程中，需要進行中弧線數據點求解、緣頭拼接和截面線離散，本文對以上三個問題進行了深入研究，並在此基礎上提出了中弧線數據點求解演算法，緣頭拼接演算法和截面線離散演算法等研究成果。 -
Based on the experiment results, the damage form of abnormal exterior joint are summarized, characteristics of hysteresis curve are studied, the effect of stirrup ratio and height of column section and beam section on anti - shear property of abnormal joint are discussed, working mechanism of abnormal exterior joint is researched, the conclusion that the anti - crack and bearing capacity of abnormal joint are studied by analyzing the minor core of abnormal exterior joint is proposed, the basic data is provided for the design formula of abnormal joints
根據試驗結果，總結了異型邊節點的破壞形態，研究了節點滯回曲線的特徵，討論了節點核芯配箍率、樑柱截面高度變化對異型邊節點抗剪性能的影響，分析了異型邊節點的受力機理，提出應以「小核芯」為分析單元來研究此類節點抗裂和承載力的建議，為異型節點設計公式的建立提供了基礎數據。 -
First, using strip - partitoning method and programming in matlab language, the numerical caculations of the relation curve between moment and curvature are done for the beams strengthened with non - prestressed and pretressed cfrp sheets, base on the assumption of plane section, non - bonding slip and non - peeled destroy. secondly, nolinear finite elemeant analysis by ansys are done for the beams strengthened with prestressed cfrp sheets base on the three assumptions before mentioned, the analysis are all done for the relation curve between load and displacement, the distribution of material stress, the distribution of cracks. lastly, calculation formula of flexural capacity and deflection are proposed
）的全過程關系曲線。其次基於上面的三個假定，選擇合理的本構關系，利用ansys通用有限元分析程序對預應力碳纖維布加固梁進行非線性有限元分析，分析了加固梁的荷載-撓度關系、材料的應力情況、裂縫的分佈情況等。最後提出了承載力計算公式和正常使用狀態下撓度計算公式。 -
This thesis gives a brief account of the basic theories of software engineering and computer graphics, of the data structure of individual component modeling, of the design of the software structure and of the method of realizing software. meanwhile, this thesis put more emphasis on the exploration of the arithmetic of the delaunay triangle network, nurbs curve integration, the filling - in arithmetic of triple - tree, and the arithmetic based on the scan - line arithmetic and the filling - in of complex section
文章介紹了關于軟體工程學與計算機圖形學的基本理論及其各組件模型的數據結構、軟體結構設計與軟體實現的技術方法，並重點討論了基於約束條件的delaunay三角網格化演算法、 nurbs （非均勻有理b樣條）曲面擬合、三叉樹等值線填充演算法和基於掃描線的復雜剖面填充演算法。 -
According to differences of construction process, boundary condition, temperature and stress of two schemes extending 3m deep short seam on upstream face in the middle of rcc overflow section and no short seam are calculated, what " s more, in this paper the equivalent line drawing of stable temperature field and unstable temperature field during construction and operation period and the duration curve drawing of typical points " s temperature and stress are plotted, and the results of peak and minimum on temperature in every month and maximum on tensile stress are attained
根據施工過程和邊界條件，對溢流壩段中間上游面增設3m深短縫和不設短縫兩個方案進行了溫度和應力計算，並繪制出穩定溫度場等值線圖及施工期、運行期非穩定溫度場等值線圖，典型點溫度和應力歷時曲線圖，逐月最高、最低溫度和最大拉應力及相應位置等成果。 -
Then making use of the theory, we got the rightful scale of hubei highway net. the 4th section firstly summed up the development course of hubei ' s highway, and then utilized the growth function curve to fit it
然後結合理論，對湖北省公路網的合理規模進行了探討；第4章對湖北省公路的發展歷程進行了總結，在此基礎上利用生長函數曲線對其發展軌跡進行了擬合和預測。 -
Experiment results prove that this algorithm is a practical and effective method, with which the ideal cross - section curve can be acquired. the result is coincidence to the standard iri ( the international roughness index ) and meets the necessity
實驗結論：基於陣列信號處理和小波降噪的演算法應用於路面平整度檢測可以得到較理想的斷面曲線，換算國際平整度指標iri與標定較吻合，符合處理要求。 -
Original surface is formed from boundary curve and section curve using the redevelopement interface of ug
初始曲面擬合是利用ug的二次開發功能，將截面線與邊界曲線擬合成一張初始曲面。 -
The projection and section curve graphs of workspace boundary surfaces for 6 - sps type pmts are drawn. results of analysis show that the theoretic workspace of 6 - sps trpe pmts is enveloped by 30 surface patchs. input and output ewtons of displacement analysis for double - octahedron variable geometry miss pmts are established, analytical expressions for determining singuledty configuration are derived
分別推導出了znys ztps型、 ips 3tps型和ipt ztps型並聯機床奇異倉形判別的解析表達式，得到了奇異曲面方程，並由邊界曲面分析方法得到了lps 3tps型和ipt ztps型並聯機床的工作空間，文中給出了以上混聯結構並聯機床奇異位形與工作空間分析的數值實例。 -
In chapter 3, we discuss surface restoring method based on ct data which uses the intersection algorithm between spline curve and radial to resample the section curve, then works out surface controlling point array ; take opengl to display the surface with reality and the lighting, coloring effect
第三章討論了基於ct數據的曲面重構方法，利用樣條曲線與射線的求交演算法對截面曲線進行重新采樣，並反算曲面控制點陣；在其後的顯示過程中，利用opengl實現曲面的真實感顯示，包括顏色、光照的變化等。
分享友人