selected axis 中文意思是什麼
selected axis
解釋
選定坐標軸-
A volume speed controlling system is selected on the fluid drive system of sugarcane mill, which consists of cam type axial piston variable pump and ram marathon fixed motor. an individual hydraulic system is adopted by the up - axis of the mill
甘蔗壓榨機液壓驅動系統採用斜盤式軸向柱塞變量泵與橫梁傳力內曲線馬拉松式定量液壓馬達組成容積調速閉式系統。 -
We had observed more than ten selected asteroids using 1 - meter telescope in yunnan observatory during 2000 to 2002. the observational data of seven asteroids had been reduced and analyzed. we have derived their synodic periods and estimated the shape and orientation of rotational axis for one asteroid
為此，我選定了一些直徑在125公里左右的小行星進行觀測和分析；一方面，測定它們的自轉周期，進行「角動量衰減」現象的研究，另一方面，對小行星形狀和自轉軸指向進行估算，為小行星碰撞演化研究提供更為有利的證據。 -
Finite difference time - domain method is used to calculate the reflection for these probes and absorbing boundary condition is used to deal with the singularity in the axis of the coaxial - line in the simulation. by comparing the reflection of different probes, the best probe has been selected according to sensitive requirement. the influence of parameters : such as thickness of protective film, length of protruding inner conductor of the coaxial - line probe to the measurement has been studied
通過時域有限差分法進行數值模擬分析，並採用吸收邊界處理同軸線軸心奇異點，計算出各種探頭測量相同溶液的反射系數，根據其測量的靈敏度，選出最優設計；並通過分析所選探頭的各種設計參數，如薄膜厚度、內導體伸出長度等的變化對測量結果的影響，找出該探頭各參數的最佳范圍，使其具有高度靈敏性，以適用於測量化學反應溶液的介電常數。 -
Then navigation asteroids are selected under a integral evaluation, the planning of the photoing sequence is handled with an improved genetic algorithm, along with a difference selection method which optimizes the ratio of navigation evaluation to resource consumption. a single axis randomized expanding algorithm is proposed to solve the large angle slew maneuvers planning problem. this algorithm randomly produces
對于自主探測器大角度機動規劃問題，本文提出單軸隨機擴展演算法，單軸隨機演算法在生成隨機節點過程中充分利用鄰近點的信息，把規劃問題構造空間的維數由3減少到2 ，從而減少問題求解的搜索空間，最後利用前向搜索的方法對規劃路徑進行優化。 -
Now move the selected cvs to 1. 433 of z axis ( fig 9 ), you can see the cvs ' axis value in the cvs panel ( right side )
將它們在z軸方向上移動約1 . 433的距離，你可以在右邊通道欄里看到數值 -
Capp is the important part in course of manufacturing layout. the paper adopts capp system in alternate style. according to characteristic of the prosthetic socket, the open loop control way is used in the servo system and the advantech 3 - axis high speed stepping motor control card is selected t o control three stepping motor ' s gain
針對假肢接受腔的製作特點，選擇數控機床伺服系統的控制方式為開環控制，並採用研華運動控制卡控制三個步進電機的進給，控制卡的庫文件可以實現三軸聯動功能。 -
Firstly in the paper the research of hydraulic characters and the optimize of structure have being carried out on the four bigger design schemes of permanent internal dissipation discharge tunnel reconstructed from the right bank ' s diversion tunnel of gongboxia power station with a method of theoretical analysis combined with test comparisons. on this basis, two form swirling flow internal dissipation schemes, vertical and horizontal axis are recommended to the construction unit of the station as the schemes to be selected next
本文採取理論分析與試驗比較相結合的方法，首先對黃河公伯峽水電站右岸導流洞改建為永久式內消能泄洪洞的四個較大設計方案進行了水力特性的試驗研究與體型優化，在此基礎上，向建設單位分別提供了豎井旋流內消能的推薦方案與水平旋流內消能的推薦方案。
分享友人