sensitive axis 中文意思是什麼
sensitive axis
解釋
測量軸-
Finite difference time - domain method is used to calculate the reflection for these probes and absorbing boundary condition is used to deal with the singularity in the axis of the coaxial - line in the simulation. by comparing the reflection of different probes, the best probe has been selected according to sensitive requirement. the influence of parameters : such as thickness of protective film, length of protruding inner conductor of the coaxial - line probe to the measurement has been studied
通過時域有限差分法進行數值模擬分析，並採用吸收邊界處理同軸線軸心奇異點，計算出各種探頭測量相同溶液的反射系數，根據其測量的靈敏度，選出最優設計；並通過分析所選探頭的各種設計參數，如薄膜厚度、內導體伸出長度等的變化對測量結果的影響，找出該探頭各參數的最佳范圍，使其具有高度靈敏性，以適用於測量化學反應溶液的介電常數。 -
By means of temporary stability of combining drift coefficient of angle sensor and through missile rotating two - position measurement, measuring rotating angle between the two positions by vertical sensitive axis x, and sensing the changes of ground velocity component between the two positions by horizontal sensitive axis and z, the position of the component is determined to realize the azimuth alignment before launch of tactical missile
角敏感元件漂移系數具有短期穩定性，通過轉彈前後兩位置對組合的測試，垂直敏感軸計測轉彈過程中兩位置之間的轉角，兩水平敏感軸敏感計測地速分量在前後兩位置的變化，由此計算出部件當前所在方位，從而實現戰術彈射前的方位對準。 -
The outcome suggest that, firstly, the change of light transmission with the continuous change of parameters is periodic ; secondly, as far as the degree of effect is concerned, the light transmission of air - spaced prisms is much more sensitive to the change of the parameters than that of the glue spaced ones ; thirdly, as to the prisms glued with the same dielectric, the effect of prisms whose optical axis parallels to the glued layer is intense than those whose optical axis parallels to the plane determines by the normal of incident face and that of the cut face
研究認為，激光偏光棱鏡的光強透射比隨各參量的連續變化都呈現出一定的周期性；各參量對空氣隙型偏光棱鏡的影響要比對膠合型棱鏡的影響大的多；同種介質膠合的棱鏡，各參量對光軸平行於切割斜面的設計類型比光軸平行於切割面的法線和入射端面的法線所組成的平面的設計類型的影響要大。 -
Utilizing the design of external shell, dual axis capacitive accelerometer was succeeded, and the sensitive properties were characterized and analyzed. with the assistance of signal processing circuit consisted of amplifier circuit and filter circuit, the signal from the sensitive chip is converted into the voltage signal that meets the product performance requirement. moreover, we employed micromechanical technique to fabricate the
後端信號處理電路通過放大電路及濾波電路，將敏感晶元輸出的電壓信號轉換成符合產品性能指標的電壓信號，經過電路模擬及實驗驗證了電路的可行性;利用精密機械加工技術製作的外殼使得傳感器整體化、小型化;對產品實際性能測試和環境試驗后表明，該傳感器主要技術指標滿足設計要求。 -
In this thesis, we focus on dual axis capacitance vibration transducer, which was fabricated by micro - electromechanical systems ( mems ). the operation mechanism of this kind of accelerometer was analyzed. under external acceleration, the space between sensitive quality mass and detecting electrode will change, which causes the variation of equivalent capacitance
本論文研究了採用微機械加工技術（ mems ）製作的雙軸電容式振動傳感器，其基本工作原理是利用慣性質量塊在外界加速度的作用下與檢測電極間的空隙發生改變，從而引起等效電容的變化來測定振動加速度的。 -
The exclusive konica minolta anti - shake system uses an extremely sensitive angle - speed sensor and a smooth impact drive mechanism ( sidm ) to precisely shift the ccd to compensate for camera movement on both the vertical and horizontal axis. unlike after - the - fact, digital correction systems, it does not degrade image quality. and unlike lens - mounted optical systems, it provides effective camera - shake protection with a wide range of telephoto, wide - angle, macro and standard lenses
Dynax7d的ccd移位機制有別於一般只能在拍攝后才作出補償的數碼修正系統，它並不會降低影像質素；且能兼容任何的dynax鏡頭，包括遠攝鏡、廣角鏡、微距鏡及標準鏡頭，比只安裝在鏡頭光學系統的防手震功能提供更全面的保護。 -
The optimization design of the crank - connect rod mechanism was carried out. collocating the mass reasonably, adjusting the ratio ( ( 1 - f ) / f ) of the long axis to the short axis of the ellipse track, adjusting the direction of long axis to the direction where the internal - combustion engine was not sensitive to the stimulating force. all the above contribute to the max reduction of the vibration
對單缸內燃機的曲柄滑塊機構進行優化設計，合理的布置加配質量的大小和方向，對軌跡橢圓的長短軸比率（ 1 - f ） / f進行調整，將長軸方向調整到內燃機對激振力不敏感的方向，從而使不平衡力對內燃機所產生的振動最小，以某一具體的單缸內燃機為例進行了計算分析。
分享友人