servo loop model 中文意思是什麼

servo loop model 解釋
伺服迴路模型
  • servo : n. 〈用作定語或前綴〉1. 【自動化】伺服。2. 伺服系統；隨動系統；伺服機械；從動系統。3. 【航空】舵機〈自動駕駛儀附件〉。
  • loop : n 1 （用線、帶等打成的）圈，環，匝，框，環孔，線圈；【醫學】（常 the loop）宮內避孕環。2 環狀物，...
  • model : n 1 模型，雛型；原型；設計圖；模範；（畫家、雕刻家的）模特兒；樣板。2 典型，模範。3 （女服裝店僱...
  1. In the positioning servo - system, which generally is configured by the d. c. pulse width modulator ( pwm ) velocity governing system and position servo - loop, the parameter perturbance of pwm velocity loop really exist by reason of such as the load behavior ; power voltage supply ; operating setting value, etc. 1, 2 ， and it cannot be ignored. by using the identification technique to form the mathematical model of the system, authors have confirmed the facts. therefore, to design the discrete sliding mode controller ( dsmc ) of the positioning servo - system, the perturbed parameters value bounds of the pwm velocity loop, which is as the controlled plant of position servo - loop, should be accounted. consequently, the design principle of dsmc for accounting system with parameter perturbance is proposed by the authors. the proposed method can ensure the stability of system with parameter perturbance and the behavior of non - overshoot, fast precise positioning. in order to reveal the effects of the design method, the comparative research work is done by the authors. also, it has been tested in an industrial experiment, the results proved it is satisfactory

    由直流脈寬調速系統（ pwm ）和位置環構成的定位系統中，速度環的參數隨負載特性；電網電壓；給定工況而攝動是不容忽視的.作者通過系統辨識建模也證實了這一事實1 ， 2 .因此在設計位置環的離散滑模控制時，必須針對速度環（即位置環的控制對象）的參數攝動范圍採用「對象參數攝動離散滑模控制器的設計方法」 ，以確保系統在參數攝動時的穩定性和快速、無超調、準確定位的優良動態品質.為剖析該設計方法的控制效果，本文作了對比性研究，並將該設計方法用於工業試驗中，取得了滿意的結果
  2. The paper makes a systematic study on frictional torque model for hydraulic system, after the analysis of the ultra ? low speed principle of closed - loop system, it can be concluded that the existence of the difference between static frictional and dynamic frictional torque, and the periodic saltation of the dynamic frictional torque, are the main reasons of the low speed stick - skip to the electrohydraulic position servo system

    針對伺服馬達的低速性能，進行了低速實驗研究，併兼顧快速性能進行了階躍響應和正弦響應實驗研究，對實驗結果進行了分析，得出了一些有價值的結論，提出下一階段進行實驗的建議。
  3. Comparing and analyzing the synchronous control strategy, which brings up the new method to control the double un - symmetry jars proceed synchronously with the combination of proportional valve and servo valve, which forms closed loop control ; basing on the above methods, models are made to get mathematics models of position control system and to analyze system model theoretically by using pid controller, we can realize regulating parameters, minimizing synchronous errors and enhancing the dynamic performances ; the simulink tool box in matlab software is used to imitate the system according to the model, which not only makes the result visual and easy to adjust the parameters in interactive way but also lets us understand the effects of different parameters and optimizes the dynamic properties. the theory of plc control in dshp is discussed after advanced understanding of the system movements. hardware design and general regulation are given on the base of siemens company products s7 - 200 plc

    本文根據大量的國內外文獻，對研配液壓機的工作原理及設計結構進行了簡介；對位置同步的控制方法進行了比較分析，提出比例閥和伺服閥復合控制的閉環結構來對非對稱雙缸進行同步控制電液比例同步控制方案；在此基礎上著重對比例閥控非對稱缸建模，最後得到位置控制系統的總體數學模型，從理論上對同步系統動態特性進行了分析，並用pid控制器進行參數整定，減小雙缸同步誤差、提高系統的動態響應性能；其中控制性能的分析藉助于matlab軟體中的simulink工具箱，由已建立的數學模型形成模擬模型，得到可視化的模擬結果，從而利於交互方式下調整參數，了解不同的參數對系統的影響，優化同步系統的動態性能；在深入了解系統的動作特性后，對plc控制研配液壓機的原理進行了探討，針對siemens公司s7 ? 200型plc給出了硬體設計的總體規劃，編制出研配液壓機動作控製程序，在編程中著重研究位移傳感器與plc的通訊、雙缸同步運行的pid控制在plc上的實現及bcd碼撥盤輸入程序的植入問題。
  4. Piston ring is the important accessory of the engine and turning its contour is the key procedure to ensure the performance of piston ring it has great value in economy and society that we develop the nc machining system for outer circle of piston ring to manufacture the high quality piston ring and to replace the import machine according to piston ring contour data provlded by the cad system ， it can turn the piston ring contour by controlling the displacement of servomechanism which is controlled by the angle of servo motor it uses the theories of velocity closed loop 、 dlsplacement closed loop and feed forward control to improve the control precision of system on the basis of theories of elastic mechanics and mathematics ， the cad system can provide the accurate data required by the nc machine system according to the calculation model and the parameters of piston ring this system integrates the cad cam technology

    系統根據活塞環cad系統生成的介面數據，通過伺服電機的轉角位置控制自主研製的高性能微位移進給機構產生給定的位移，以完成活塞環輪廓的仿型加工。系統採用速度、位置閉環控制及前饋控制理論，以提高系統的控制精度。活塞環cad系統以彈性力學和數學方法為基礎，根據常用的計算模型與活塞環參數自動生成數控加工系統所需的精確的介面數據，實現cad / cam一體化。
分享友人
分享到 Line

分享到臉書