shaft alignment 中文意思是什麼
shaft alignment
解釋
樞軸對準-
Bushings ( 4 ) : furnishes shaft support at three locations for positive shaft alignment and actuator support
襯套（ 4 ） ：在三個位置上配置軸支撐，有利於軸校直和執行機構的支撐。 -
During the shipbuilding in major shipyards worldwide, plenty of problems are generated out of shaft alignment, which results in the over - tolerance of main engine crank shaft, high temperature of bearing and excessive vibration
在船舶的建造過程中，世界各大船廠，都多次出現過軸系校中的問題，導致主機拐檔差超差，軸承高溫或造成振動過大等。 -
The quality of shaft alignment, is of vital importance in ensuring the long term appropriate running of shafting system and shortening the construction period of shipbuilding, also crucial in keeping the sailing vessel in the set course
船舶軸系校中的質量，對于確保軸系長期正常地運轉和縮短船舶修造周期都非常重要，也是船舶正常航行的關鍵。 -
It introduces a precision and quick way to check proper alignment of rotating reel shaft in ship unloader with the gearbox output shaft
摘要介紹1種可以高精度、快速測量碼頭卸船機捲筒旋轉軸與齒輪箱輸出軸對中的方法。 -
A common recognized method for the shaft alignment, is to set up a physical model, and appropriately locate each bearing in compliance with the required bearing load, stress and shear force and slop etc, so as to fix the shaft with the curve line as required and obtain a right distribution of bearing load
對于軸系校中計算，國內外比較通用的方法是對軸系相關的要素進行處理，建立物理模型，按照規定的軸承負荷、應力，轉角等限制條件，確定各軸承的合理位置，將軸系安裝成規定的曲線狀態，以達到使各個軸承上的負荷合理分配。 -
The single coil - spring and flexible bellows design provides self - alignment which automatically adjusts to compensate for shaft endplay, run out, primary sealing ring wear, reverse pressure and equipment tolerances
單螺旋彈簧和柔性波紋管用於自排列，能夠自動調節補償軸所受到的排擠，溢出，主密封環磨損，反壓力和設備公差。 -
Has the shaft alignment been finished
軸的對中任務完成了嗎？ -
This article states the applicable method for the shaft alignment calculation and rationale in element process, setup of model and alignment calculation
本文闡述了軸系校中計算的方法及計算過程中，要素的處理，模型的建立，校中計算的基本方法。 -
No need of alignment when employing a torque arm ( optional part ). installation can be compelted only by inserting a driven shaft to the hollow output shaft of the gearmotor
在使用反扭矩桿（可選部件）時無需定位調整，只要將從動插入齒輪減速機的空心輸出軸即可完成安裝。 -
Stuffing box is integral with agitator housing for positive alignment of shaft
依據混合器軸的實際安裝情況，一個完整的填料箱。 -
Stuffing box is integral with agitator base for positive alignment of shaft
依據混合器軸的實際安裝情況，設計一個完整的填料箱。 -
Alignment inspection installation of shaft generator and gear box
軸帶發電機及齒輪箱安裝檢查。 -
Severe protests from local residents living along mrt routes during the route alignment coordination caused a two - year delay to the proposed schedule for the hsingchuang line. therefore, to reduce the extent of tunneling is a key consideration in the long - term planning of mrt routes. other downsides to the single tunneling method are that it requires longer construction time, and that two break throughs from the tunnel to the work shaft involve a higher construction risk
另因採用單孔潛盾隧道須鉆掘上、下行隧道，除施工時程較長外，且兩次破鏡將增加施工之風險，故有鑒于潛盾機之技術日新月異，國外已有採用多圓形潛盾工法（ mf工法）之成功案例，此除可減少用地徵收補償之困擾外，且可減少隧道開挖面積進而減少棄土所造成之問題。
分享友人